@article { author = {Shafaee, Mahdis and افرا, الیاس and Ghasemiyan, Ali and Dhghani Firozabadi, Mohammad reza and Ebrahimi, Poneh}, title = {Comparative study on antimicrobial property of cellulose-silver nanocomposite and cellulose film coved by Ag nanoparticles}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {31}, number = {4}, pages = {541-556}, year = {2016}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2016.106597}, abstract = {In recent years, there has been a lot of attention in producing and using of renewable and environmental friendly cellulose film and coverage. Regarding to the application of these films and coverages in different industries such as food, packaging and medical industries, their antimicrobial property is apparent. The purpose of this research is producing cellulose antibacterial film. At first, long fibr pulp convert to NFC using a supergrinder and then nanosilver treated films prepared applying silver nitrate through two different ways. In the first method, silver nanoparticles with considerations of 5 and 10 ppm reduced on NFC particles’ surface using retention aid. In second methods the prepared NFC film has been immersed in solution of Ag nanoparticle in concentration levels of 5 and 10 ppm. On higher concentration of used nanosilver solution, the amount of retained Ag nanoparticle in the first method was higher than the second one whereas, on lower concentration one, the differences of retained nanosilver values between two methods was a little. It has worth of mentioning that immerging method has the benefit of avoiding Ag nanoparticle wasting during pulp draining and nanosilver solutions could be reused simply.}, keywords = {Nano composite,Immersion,Nano Fibrillated cellulose,Nanosilver,Antibactrial}, title_fa = {بررسی مقایسه‌ایی خواص ضد‌میکروبی نانو‌کامپوزیت سلولز- نقره و فیلم نانو‌سلولز پوشش‌دهی شده با نانو‌نقره}, abstract_fa = {در سال‌های اخیر تولید فیلم و به‌کارگیری پوشش‌های سلولزی زیست‌تخریب‌پذیر و دوستدار محیط‌زیست به ویژه از نانو‌ذرات سلولزی توجهات زیادی را به خود جلب کرده است. متناسب با کاربرد این محصولات در صنایع مختلفی چون صنایع غذایی، دارویی و بسته‌بندی، اهمیت بهبود ویژگی ضد‌باکتری این محصولات را پیش از پیش آشکار می‌سازد. در این تحقیق با هدف تولید پوشش‌های سلولزی ضد‌باکتری، ابتدا سلولز نانو‌فیبریله‌شده از خمیر الیاف بلند به شیوه مکانیکی آسیاب کردن تولید شده و سپس به کمک ذرات نانو‌نقره (به‌کارگیری نیترات‌نقره و احیاء با سدیم‌بورهیدرید)، با دو روش، تولید فیلم صورت پذیرفت. در روش اول با کمک پلی‌دادمک، ذرات نانو‌نقره در دو سطح 5 و 10 ppm بر روی NFC احیاء وسپس از نانو‌کامپوزیت NFC/نانو‌نقره فیلم تولید گردید. در روش دوم ابتدا فیلم NFC تولیدگردیده وسپس به ‌وسیله غوطه‌وری آن در محلول نانو‌نقره در دو سطح 5 و10 ppm، فیلم‌های ضد‌باکتری به دست آمد. میزان ماندگاری نانو‌نقره در روش اول در غلظت‌های بالاتر بیشتر از شیوه غوطه‌وری به‌دست آمد. اما در غلظت‌های کم‌تر( ppm5) اختلاف ماندگاری نانو‌نقره در دو شیوه اندک بوده است. لازم به ذکر است که شیوه غوطه‌وری مزیت بزرگ عدم هدر رفت نانو‌نقره و ورود آن به طبیعت در طی آبگیری که در شیوه اول متعارف است را ندارد ومحلول نانو‌نقره با افزایش غلظت قابل استفاده مجدد می‌باشد.}, keywords_fa = {نانو‌کامپوزیت,غوطه‌وری,سلولز نانو‌فیبریله‌شده,نانو‌نقره,ضد‌میکروبی}, url = {https://ijwpr.areeo.ac.ir/article_106597.html}, eprint = {https://ijwpr.areeo.ac.ir/article_106597_e64acf97cdebbf2a6c3e901e23d839a5.pdf} } @article { author = {Kargarfard, Abolfazl and nourbakhsh, Amir and Golbabaei, Fardad}, title = {Utilization of Recycled Polyethylene For Physical & Mechanical Properties Modification of Particleboard}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {31}, number = {4}, pages = {557-568}, year = {2016}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2016.101480}, abstract = {The aim of this study has been utilization of recycled polyethylene in modification of physical and mechanical properties of particleboard. Therefore, three levels of resin consumption content ( 10, 7 and 4% ) and three levels of recycled polyethylene consumption content 5, 10 and 15% in surface layer of mat, particleboards produced. Also in order to influence of these variables on physical and mechanical properties of produced boards, 3 particleboards with 10% resin content in surface layer and without polyethylene as control samples produced. The physical and mechanical properties of boards measured and analyzed. The results of this study indicated that with increasing of the recycled polyethylene consumption content, the MOR, MOE and thickness swelling of boards improved significantly and the produced boards with 15% recycled polyethylene in compare with control boards increased 59 and 53% respectively. Also the results revealed that the water absorption of boards decreased with increasing of increasing of recycled polyethylene consumption content, and the minimum of water absorption of boards observed in the produced boards with 15% recycled polyethylene. Based on the results of this research and with increasing of polymeric residues in the envirement , we conclude that the utilization of recycled polyethylene in particleboard production has different advantages.}, keywords = {Recycled Polyethylene,Particleboard,Thickness swelling,Water Absorbtion}, title_fa = {استفاده از پلی اتیلن بازیافتی برای بهبود ویژگیهای فیزیکی و مکانیکی تخته خرده چوب}, abstract_fa = {هدف از این بررسی استفاده از پلی اتیلن بازیافتی برای اصلاح ویژگیهای تخته خرده چوب بوده است. بنابر این با استفاده از 3 میزان مصرف چسب 10، 7 و 4 درصد و 3 میزان مصرف پلی اتیلن بازیافتی 5، 10 و 15 درصد (بر اساس وزن خشک خرده چوب) در لایه سطحی کیک خرده چوب اقدام به ساخت تخته خرده چوب گردید. نتایج نشان داد افزایش مقدار مصرف پلی اتیلن باعث بهبود مقاومت خمشی و مدول الاستیسیته تخته های ساخته شده می گردد. به طوری که مقاومت خمشی و مدول الاستیسیته تخته های ساخته شده با کاربرد 15 درصد پلی اتیلن نسبت به تخته های شاهد به ترتیب در حدود 59 و 53 درصد افزایش داشته است. همچنین واکشیدگی ضخامت تخته ها با افزایش مصرف پلی اتیلن بهبود یافته است و حداقل واکشیدگی ضخامت 2 ساعت در شرایط مصرف چسب 10 درصد و 15 درصد پلی اتیلن بازیافتی به دست آمده است که کمتر از 10 درصد تخته های شاهد می باشد. افزایش مقدار مصرف پلی اتیلن، جذب آب تخته ها را کاهش داده است و حداقل آن در تخته های دارای 15 درصد پلی اتیلن مشاهده گردید. به طوری که با مصرف 15 درصد پلی اتیلن تا حدود 58 درصد در جذب آب 2 ساعت آنها در مقایسه با تخته های شاهد کاهش دیده شد. به طور کلی می توان بیان داشت یکی از بهترین راهکارها برای کاهش ضایعات پلیمری و تولید محصولاتی با ارزش افزوده بالا، به کارگیری آنها در جهت بهبود ویژگیهای تخته خرده چوب می باشد}, keywords_fa = {پلی اتیلن بازیافتی,تخته خرده چوب,واکشیدگی ضخامت,جذب آب}, url = {https://ijwpr.areeo.ac.ir/article_101480.html}, eprint = {https://ijwpr.areeo.ac.ir/article_101480_2f77ed325da1f2af5e52375666caf3ce.pdf} } @article { author = {Vaysi, Ramin and Nikkar, Mohammad and Salarian, Hamidreza}, title = {Investigation and Comparison of Newsprint Properties from Bleached CMP Pulp of Ash and Orange Woods}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {31}, number = {4}, pages = {569-580}, year = {2016}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2016.106287}, abstract = {In this study, the possibility of using ash and orange bleached CMP pulp as replace in the full or part of CMP pulp of Mazandaran Wood and Paper Industries (MWPI) for making newsprint was investigated. For this purpose, first, ash and orange CMP pulps were prepared by using cooking conditions of MWPI with 101 gr/lit Na2O at the yield 85% in 75 minutes. Then some of the CMP pulps bleached with hydrogen peroxide, then its mixed samples with 15, 30, 45 and 60 percent to CMP pulp mill (control sample). From the mixed pulps provided hand sheets with 60 gr/m2 and these optical and mechanical properties measured and the data average were analyzed and compared. The results showed that newsprint from ash CMP pulp were more suitable than CMP pulp mill in all measured properties (except brightness) and orange CMP pulp (except opacity). Following bleaching with hydrogen peroxide, the brightness, tear, burst, tensile and breaking length strengths increased and opacity decreased. The results showed that ash and orange unbleached CMP pulps are not good properties for newsprint production and these pulps have to bleach with hydrogen peroxide. In generally, the best mixed pulps were includes 45-60 percent ash and orange bleached CMP pulps with 40-55 percent MWPI CMP pulp for newsprint production.}, keywords = {CMP pulp,Orange,Ash,bleaching,newsprint,Optical and mechanical properties}, title_fa = {بررسی و مقایسه ویژگی های کاغذ روزنامه حاصل از خمیر کاغذ شیمیایی- مکانیکی (CMP) رنگبری شده چوب نارنج و زبان گنجشگ}, abstract_fa = {در این تحقیق امکان استفاده از خمیرکاغذ CMP رنگبری شده چوب نارنج و زبان گنجشگ به عنوان جایگزین تمام یا بخشی از خمیرکاغذ CMP کارخانه چوب و کاغذ مازندران برای تولید کاغذ روزنامه مورد بررسی قرار گرفت. بدین منظور، ابتدا با شرایط پخت کارخانه مذکور و با Na2O 101گرم برلیتر، در دمای 165 و در زمان پخت 70 دقیقه، از چوب نارنج و زبان گنجشگ خمیرکاغذ CMP با راندمان 85 درصد تولید شد. سپس این خمیر کاغذها با پروکسید هیدروژن رنگبری و با نسبت های 15 ، 30 ، 45 و 60 درصد جداگانه با خمیرکاغذ CMP کارخانه چوب و کاغذ مازندران (نمونه شاهد) مخلوط گردید. از هر نمونه کاغذ دست ساز با وزن پایه 60 گرم برمتر مربع تهیه شد و خواص نوری و مقاومتی آن طبق آزمون های استاندارد TAPPI اندازه گیری ومورد تجزیه و تحلیل آماری قرار گرفت. نتایج نشان داد که کاغذ حاصل از خمیر CMP زبان گنجشگ درتمامی ویژگی های اندازه گیری شده (بجز روشنی) مناسب تراز نمونه شاهد و خمیر CMP نارنج(بجز ماتی) بوده است. در اثر رنگبری با پروکسید هیدروژن، روشنی، مقاومت های به پارگی، ترکیدن، کششی و طول پارگی افزایش و ماتی کاغذ حاصل کاهش داشته است. نتایج نشان داد که خمیرکاغذ خالص سفید نشده چوب نارنج و زبان گنجشگ ویژگی مطلوبی برای تولید کاغذ روزنامه را ندارد و لازم است این خمیرکاغذ ها با با پروکسید هیدروژن رنگبری شوند. به طوری کلی، بهترین ویژگی های مقاومتی نیز در کاغذ روزنامه حاصل از اختلاط 60-45 درصد خمیرکاغذ CMPنارنج و زبان گنجشگ(جداگانه) با 40-55 درصد خمیرکاغذ CMP کارخانه مشاهده گردید.}, keywords_fa = {خمیر CMP,نارنج,زبان گنجشگ,رنگبری,کاغذروزنامه,خواص نوری و مقاومتی}, url = {https://ijwpr.areeo.ac.ir/article_106287.html}, eprint = {https://ijwpr.areeo.ac.ir/article_106287_768b54c2c484633a4ab4662553ead9c0.pdf} } @article { author = {Ghofrani, Mohammad and ghiyasvand, afrooz}, title = {Investigation of the domestic living furniture producer’s point of view on the way of manufacturing and selling of these products}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {31}, number = {4}, pages = {581-594}, year = {2016}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2016.106288}, abstract = {Nowadays, the leading experts of the world’s furniture industry approve the existence and potentials of Iran furniture industry and more importantly, they believe it can advance and grow much more in the future. So, the purpose of this paper is investigating of the domestic living furniture producer’s point of view on the way of manufacturing and selling of these products. In this regard, information from aware academic specialists was gathered. Then five indices, affecting the production and sell of furniture, was determined and used in the form of a standard questionnaire. In order to check the validity and reliability of the survey, Cronbach’s alpha coefficient and content validity methods were used, respectedly. Ultimately, rating the indices by Leikert method showed that: customer focus, collaboration with the academics, imported furniture, designing and finally producer’s satisfaction of government and business suporters, respectedly had the most to least degree of importance for domestic living furniture producers to the way they manufacture and sell their furniture products.}, keywords = {Index,living furniture,domestic producers,manufacturing and selling}, title_fa = {بررسی رویکرد تولیدکنندگان داخلی مبلمان نشیمن در تولید و فروش این محصولات}, abstract_fa = {امروزه کارشناسان معتبرترین بخش از صنعت مبلمان جهان، موجودیت و پتانسیل های صنعت مبلمان ایران را به رسمیت می شناسند و مهمتر این که برای آن شانس رشد و توسعه بسیار زیادی قائل هستند. هدف از این تحقیق بررسی دیدگاه تولیدکنندگان داخلی مبلمان نشیمن در زمینۀ تولید و فروش این محصولات می باشد. در این راستا با کسب اطلاع از نظر متخصصین آگاه دانشگاهی و روش های تحقیق اسنادی و پیمایشی ، پنج شاخص مؤثر بر تولید و فروش محصولات مبلمان منزل، در قالب پرسشنامه ای استاندارد طراحی شد. برای بررسی روایی پرسشنامه از روش آلفای کرون باخ و برای ارزیابی اعتبار آن از روش اعتبار محتوی استفاده گردید. رتبه بندی شاخص های اصلی با روش طیف لیکرت نشان داد که از منظر تولید کنندگان داخلی، به ترتیب شاخص های مشتری مداری، همکاری با دانشگاهیان، مبلمان وارداتی، طراحی و رضایت مندی از حمایت های دولتی و اصناف، دارای بیشترین تا کمترین درجه اهمیت در تولید و فروش محصولات مبلمان منزل هستند.}, keywords_fa = {شاخص,مبلمان نشیمن,تولید کنندگان داخلی,تولید,فروش}, url = {https://ijwpr.areeo.ac.ir/article_106288.html}, eprint = {https://ijwpr.areeo.ac.ir/article_106288_33a9bbb316e31ab4cf9e0e67477bd321.pdf} } @article { author = {Hatamzadeh Arabi, Elham and Ghorbani, Maryam and Biparva, Prya}, title = {Effect of insitu synthesis of zinc oxide nanoparticles on the mechanical and biological properties of a wood-polymer composite}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {31}, number = {4}, pages = {566-576}, year = {2016}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2016.106761}, abstract = {The current research work was planned to investigate the possibility of zinc oxide nanoparticles synthesis using hydrothermal method in wood structure and its effect on mechanical and biological properties of wood-polymer composite. Test samples were divided to control and treated with styrene, zinc oxide nanoparticles, nanocomposite and nano/Styrene. Mechanical and biological tests samples according toASTM-D143 and EN113 respectively were treated by vacuum- pressure method using cylinder experimental. The mechanical tests were considered for each level 5 repeat and for biological test for each level 10 repeat. The presence of zinc oxide nanoparticles on cell wall and styrene in the cell cavities were confirmed by Scanning electron microscopy. According to the results, bending strength, bending modulus, hardness and pressure parallel to grain for nano/styrene samples with highest improvement were increased 36.74, 40.23, 60.58 and 25.07 in comparison with control respectively. Also, decay resistance of treated samples increased, so that maximum and least weight loss were recorded for control and nano/styrene samples with 25.81 and 3.37% weight loss.}, keywords = {Zinc oxide nanoparticles,hydrothermal method,wood-polymer,MECHANICAL PROPERTIES,decay resistance}, title_fa = {اثر سنتز درون‌بافتی نانو‌ذرات اکسید‌روی بر خواص‌مکانیکی و زیستی فرآورده چوب‌پلیمر}, abstract_fa = {در این پژوهش امکان سنتز نانو‌ذرات‌اکسید‌روی به روش هیدروترمال و اثر آن بر خواص‌مکانیکی و زیستی فرآورده چوب‌پلیمر صنوبر (Populous deltoides) مورد ارزیابی قرارگرفت. تحقیق به پنج تیمار شاهد، استایرن (St)، نانواکسیدروی (N)، نانوکامپوزیت (NC) و نانواکسیدروی/ استایرن (NSt) گروه‌بندی شد. نمونه‌های آزمون مکانیکی و زیستی تهیه شده براساس استانداردهای ASTM-D143 و EN113، در سیلندر اشباع، به روش خلاء- فشار، اشباع شدند. در آزمون مکانیکی، برای هر تیمار 5 تکرار و در آزمون زیستی، برای هر تیمار 10 تکرار در نظر گرفته شد. تصاویر میکروسکوپ الکترونی حضور نانوذرات-اکسیدروی در دیواره‌ سلولی و استایرن در حفرات سلولی را تاییدنمود. نتایج نشان‌داد که مقاومت‌خمشی، مدول‌خمشی، سختی و فشار موازی‌الیاف در تیمار NSt با بالاترین بهبود نسبت به نمونه شاهد، به ترتیب 74/36، 23/40، 58/60 و07/25 درصد افزایش یافت. مقاومت به پوسیدگی نمونه‌های تیمار شده نیز نسبت به نمونه‌های شاهد افزایش یافت، به طوری‌که بیشترین کاهش وزن در نمونه‌های شاهد، 81/25 درصد و کمترین کاهش وزن در تیمار NSt، 37/3 درصد مشاهده شد.}, keywords_fa = {چوب‌پلیمر,خواص مکانیکی,فرآیند هیدروترمال,مقاومت به پوسیدگی,نانو‌اکسید‌روی}, url = {https://ijwpr.areeo.ac.ir/article_106761.html}, eprint = {https://ijwpr.areeo.ac.ir/article_106761_e08bd648d87da2c9cd4dca27f62237b2.pdf} } @article { author = {Esmaeili, Neda and Ghorbani, Maryam and Biparva, Porya}, title = {Effects of the Combined Modification Process of Glutaraldehyde/ paraffin on Biological and Mechanical properties of Poplar wood}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {31}, number = {4}, pages = {606-620}, year = {2016}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2016.106762}, abstract = {In this study, the mechanical and biological properties of modified poplar wood with glutaraldehyde and paraffin were investigated. Modification was performed with glutaraldehyde at different concentrations of glutaraldehyde, 5, 10 and 20% using magnesium chloride as a catalyst and then subsequently with paraffin by vacuum-pressure method. Increasing concentration of glutaraldehyde caused to weight gain and bulking wood cell wall, subsequently reduced paraffin penetration into the porous structure of wood. Biological resistance exposed to white rot fungi and mechanical properties were measured according to the standards EN113 and ASTM D143-94, respectively. Scanning electron microscopic images showed bulking of cell walls and paraffin presence in cell cavities. According to results of TGA, increasing of modification intensity decreased mass loss due to cross linking formation between glutaraldehyde and cell wall polymers. Paraffin at combined modification containing 10% and 20% glutaraldehyde improved significantly the modulus of elasticity. Glutaraldehyde reduced bending strength, but paraffin present in the modified samples improved it. The Glutaraldehyde increased compression strength parallel to grain and hardness that the improvement was more obvious in combined modification. Modification with glutaraldehyde enhanced decay resistance exposed to white rot fungi, and this improvement intensified at the presence of paraffin. Inhibitory influence of chemical modification on wood attacking white rot fungi can be attributed to decreases the wood moisture, bulking of cell walls and blocking cell cavities.}, keywords = {Glutaraldehyde,Paraffin,MECHANICAL PROPERTIES,White rot}, title_fa = {اثر اصلاح ترکیبی گلوتارآلدئید/پارافین بر ویژگی‌های زیستی و مکانیکی چوب صنوبر (Populus deltoides)}, abstract_fa = {در این تحقیق ویژگی‌های مکانیکی و زیستی چوب صنوبر اصلاح‌شده با گلوتارآلدئید و پارافین بررسی شد. اصلاح با گلوتارآلدئید در 3 سطح غلظت 5، 10 و 20درصد همراه با کاتالیزور کلرید‌منیزیم و متعاقباً در سطوح اصلاح ترکیبی، اشباع با پارافین به‌روش خلا-فشار انجام شد. افزایش سطح غلظت گلوتارآلدئید، به افزایش وزن و حجیم‌شدگی دیواره سلولی چوب منتهی‌شد که متعاقب آن میزان نفوذ پارافین به ساختار متخلخل چوب کاهش یافت. مقاومت زیستی در معرض قارچ پوسیدگی سفید و خواص مکانیکی به‌ترتیب طبق استاندارد‌های EN113و ASTM D143-94 اندازه‌گیری شد. تصاویر ریزنگار الکترونی گسیل‌میدانی گویای حجیم‌شدگی دیواره‌ها و حضور پارافین در حفرات بود. در بررسی پایداری حرارتی، با افزایش شدت اصلاح، میزان افت‌جرم روند کاهشی داشت که این امر به‌دلیل ایجاد اتصالات عرضی بین گلوتارآلدئید و پلیمرهای دیواره‌ای است. نتایج آزمون خواص مکانیکی نشان داد که ورود پارافین در سطوح اصلاح ترکیبی حاوی 10 و 20درصد گلوتارآلدئید، بهبود معنی‌دار مدول‌الاستیسیته را به‌همراه‌داشت. گلوتارآلدئید به کاهش مقاومت خمشی انجامید که حضور پارافین آن‌را در سطوح اصلاح‌شده بهبود‌بخشید. حضور گلوتارآلدئید به بهبود فشار موازی الیاف و سختی منتهی‌شد که در اصلاح‌ترکیبی این اثر محسوس‌تر بود. اصلاح‌ گلوتارآلدئید موجب بهبود مقاومت در معرض قارچ پوسیدگی سفید گردید که این نیز در حضور پارافین افزایش معنی‌داری نشان داد. بهبود مقاومت چوب‌اصلاح‌شیمیایی‌شده در برابر قارچ‌پوسیدگی سفید را می‌توان به کاهش رطوبت چوب، حجیم‌شدن دیواره‌سلولی و مسدود شدن منافذ ریز دیواره نسبت داد.}, keywords_fa = {گلوتارآلدئید,پارافین,خواص مکانیکی,پوسیدگی سفید}, url = {https://ijwpr.areeo.ac.ir/article_106762.html}, eprint = {https://ijwpr.areeo.ac.ir/article_106762_e4e57ca1be0eff0698fa182eac2d9fdc.pdf} } @article { author = {Taghiyari, Hamid Reza and Ghofrani, Mohammad and Arbabi ghamsari, Farzad}, title = {Study on the tensile and compression tension-carrying capacity of corner V-nails}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {31}, number = {4}, pages = {621-633}, year = {2016}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2016.106763}, abstract = {The present research project was carried out to find out tension-carrying capacity of corner miter V-joints in tensile and compression directions to be compared with those of dovetail joints. Variables included the type of wood-composites to produce the joints (MDF and particleboard), the number of V-nail in each joint (2, 3, and 4 V-nails), and the height of V-nails (7 and 10 mm). Separate sets of joints were produced with and without polyvinyl acetate resin. Results demonstrated that the tension-carrying capacity under compression tension was significantly higher than those in the tensile tension. Moreover, MDF joints showed higher tension-carrying capacity in comparison to those made from particleboard. Joints with resin were significantly stronger than those without resin. Increase in the number of V-nails resulted in an improvement in the tension-carrying capacity in both directions. Based on the results of the present research project, it was concluded that V-nails are preferred to dovetail joints from different perspectives, including their lower production expenses, lack of need for an extra step to mill the joint so that joint bits be inserted into, fast and easy installation of V-joint in one-step process, as well as higher tension-carrying capacity. Based on the obtained results indicating the maximum tension-carrying capacity of 13.7 MPa and 28 MPa for V-nails without and with adhesive, respectively, it was concluded that 4 V-nails with 10 mm in height in MDF joint-members would be recommended for joints without resin. In case of joints with resin, MDF joint-members with 3 V-nails of 10 mm would provide the highest tension-carrying capacity for craftsmen and producers of furniture and cabinets.}, keywords = {Cabinet-Making Industry,Corner joint,Diagonal tensile and compression,tension-carrying capacity,Medium-density fiberboard (MDF),V-nail}, title_fa = {بررسی ظرفیت تحمل تنش کششی و فشاری با اتصال دهنده فلزیv– شکل در اتصالات گوشه}, abstract_fa = {این پژوهش با هدفبررسی ظرفیت تحمل تنش در اتصال‌های گوشه‌ای فارسی ساخته‌‌شدهبا اتصال‌دهنده فلزیv- شکل و مقایسه آن با اتصال کلید پاپیونی در زیر بار‌کششی و فشاری انجام‌ ‌شده‌است. متغیرهای تحقیق عبارت بودند از نوع اعضای اتصال (تخته خرده چوب و MDF)، تعداد اتصال‌دهنده در 3 سطح 2، 3و 4 عدد، و ارتفاع اتصال‌دهنده در دو ارتفاع (7و 10 میلی‌متر) ؛ همچنین، هر نوع اتصال در دو حالت با چسب و بدون چسب بررسی شد. نتایج نشان داد که ظرفیت تحمل تنش اتصال‌ها زیر بار فشاری بیشتر از ظرفیت تحمل تنش زیر بار کششی بود. ظرفیت تحمل تنش اتصال‌های ساخته شده با اعضا MDF نسبت به اتصال‌های ساخته شده با تخته خرده چوب بیشتر بود. اتصال‌های ساخته شده با چسب نسبت به اتصال‌های ساخته شده بدون چسب عملکرد بهتری داشتند. افزایش تعداد و ارتفاع اتصال‌دهنده v- شکل باعث افزایش ظرفیت تحمل تنش شد.به طور کلی استفاده از اتصال‌دهنده v- شکل به دلیل هزینه کم، عدم نیاز به یک مرحله کاری بیشتر جهت برش شکاف اتصال، نصب یک مرحله‌ای، سریع، و آسان و همچنین ظرفیت تحمل تنش بیشتر بر اتصال کلید پاپیونی ترجیح دارد. مطابق نتایج، حداکثر ظرفیت تحمل تنش MPa7/13و MPa 28 در حالت بدون چسب و با چسب اتصال دهنده v- شکل، استفاده از اعضای MDF با ارتفاع اتصال دهنده 10 میلی متر و تعداد 4 عدددر حالت بدون چسب ،و استفاده از اعضای اتصال MDFبا ارتفاع اتصال‌دهنده 10 میلی متر و تعداد 3 عدد در حالت اتصال‌دهنده به همراه چسببه تولیدکنندگان کابینت، دکورسازان و مبل سازان پیشنهاد می گردد.}, keywords_fa = {صنعت کابینت سازی,اتصال گوشه‌ای,کشش و فشار قطری,ظرفیت تحمل تنش,تخته فیبر با دانسیته متوسط(MDF),اتصال V}, url = {https://ijwpr.areeo.ac.ir/article_106763.html}, eprint = {https://ijwpr.areeo.ac.ir/article_106763_8d6da7011e1c8719e52b7305a3d32993.pdf} } @article { author = {lashkarizadeh, maryam and Borhani, Mohammad reza}, title = {Investigation the position of wood and paper industry in the economic sector in Iran by input-output approach}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {31}, number = {4}, pages = {634-647}, year = {2016}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2016.106765}, abstract = {Considering the importance of the wood and paper industry for the Iranian economy and interaction and linkages between the wood and paper sector with other economic sectors. In order to do so, Input-Output table for 1380 and hypothetical extraction method has been used. Calculation of sensitivity index of publication as well as the wood and paper industry publishing strength index respectively with figures 451.2 and 378.1 suggests that this industry ranked first and third release power sensitivity in between sections is And this means that the wood and paper industry, more than the average total other sections with the other categories in this connection and communication as well as alike and more balanced sections. In the case of the hypothetical extraction method from the perspective of the production output decreased the amount of million 112345678 (Leontief pattern) and 132456789 cents (gosh pattern). In terms of stretching the production ranking 19 of 34 of its assigned section.}, keywords = {wood and paper industry,Input-output table,backward and forward linkages,hypothetical extraction method}, title_fa = {بررسی جایگاه صنعت چوب و کاغذ درمیان بخشهای اقتصادی ایران با رویکرد داده-ستانده}, abstract_fa = {با توجه به اهمیت صنعت چوب و کاغذ برای اقتصاد ایران و ارتباط این بخش با سایر بخش‌‌ها، مطالعه حاضر با هدف بررسی ارتباطات متقابل و پیوند بین بخش چوب و کاغذ با دیگر بخش‌های اقتصادی صورت گرفته است. برای این منظور از جدول داده- ستانده سال 1380 و روش سنتی و نوین حذف فرضی ، استفاده شده است. محاسبه شاخص حساسیت انتشار و نیز شاخص قدرت انتشار صنعت چوب و کاغذ به ترتیب با ارقام 451/2 و 378/1 حاکی از آن است که این صنعت رتبه اول حساسیت انتشار و رتبه سوم قدرت انتشار را در بین بخش ها به خود اختصاص داده و این بدین معنی است که صنعت چوب و کاغذ پیوند پسین و پیشین قوی با سایر بخش ها دارد.همچنین ارتباط این صنعت نیز با سایر بخش ها به طور یکسان و متوازن در بیشتر بخش ها توزیع شده است.در صورت حذف فرضی این صنعت از دیدگاه ستانده کاهش تولید به میزان 112345678 ریال(الگوی لئونتیف)و 132456789 ریال (الگوی گش) می باشد.از نظر کشش تولید رتبه 19 را از 34 بخش به خود اختصاص داده است.}, keywords_fa = {بخش چوب و کاغذ,جدول داده- ستانده,پیوندهای پسین و پیشین,روش حذف فرضی}, url = {https://ijwpr.areeo.ac.ir/article_106765.html}, eprint = {https://ijwpr.areeo.ac.ir/article_106765_900d09109b28a1853aac14dcf90b3404.pdf} } @article { author = {Tamjidi, Abbas and Faezipour, Mohammad Mehdi and Doosthoseini, Kazem and Ebrahimi, Ghanbar and Khademieslam, Habibollah}, title = {Investigation on the properties of oriented strand boards (OSB) made from mixture ten- year- old poplar clones}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {31}, number = {4}, pages = {648-661}, year = {2016}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2016.106766}, abstract = {In this study, the effects of mat moisture content and press temperature on physical and mechanical properties of three layered oriented strand boards were evaluated. Two levels of mat moisture content 7% and 10% and three levels of press temperature 180 ˚c , 200 ˚c and 220 ˚c were applied and 12 mm in nominal thickness laboratory boards were made from mixture of three clones of ten-year-old hybrid poplar ( populous euramericana vernirubensis, p. e. I-214, P. e. 561/41) while the strands on the surface layers are aligned in the long direction of the board and the middle layer strands are cross aligned to the surface layers. In all treatments, board targeted density of 0/7 g/cm3 and press time of 8 min and phenol-formaldehyde resin (PF) content of 7% based on the oven dry weight of the strands were held constant. The mechanical and physical properties of the boards were measured as defined in relevant European standards EN 300 for OSB/1 and OSB/2. Overall results showed that all boards made from above mentioned conditions exceed the EN 300 standards for MOR, MOE, IB and TS24. The bending properties (MOR and MOE) of boards were significantly improved as the mat moisture content increased from 7 to 10%. The highest MOR was achieved at 10% mat moisture content and 220 ˚c press temperature and the highest MOE was achieved at 10% mat moisture content and 180 ˚c press temperature. The Modulus of Rupture (MOR) and Thickness swelling (TS24) were significantly improved as the press temperature increased from 180 ˚c to 220 ˚c. The lowest TS24 was achieved at 7% mat moisture content and 220 ˚c press temperature and the highest IB was achieved at 7% mat moisture content and 200 ˚c press temperature.}, keywords = {OSB,Poplar,Colon,press time,Moisture content,Phenol-Formaldehid}, title_fa = {بررسی ویژگیهای تخته تراشه جهت دار (OSB) ساخته شده از مخلوط کلنهای ده ساله صنوبر}, abstract_fa = {در این تحقیق اثر رطوبت کیک و حرارت پرس بر خواص فیزیکی و مکانیکی تخته تراشه جهت‌دار سه‌لایه مورد ارزیابی قرار گرفت. تخته‌های آزمایشگاهی به ضخامت 12 میلیمتر، در حالی که جهت تراشه‌های لایه سطحی در جهت طول تخته و جهت تراشه‌های لایه میانی ، عمود بر لایه سطحی بود، از مخلوط چوب سه کلن ده ساله صنوبر دو رگه (populus euramericana vernirubensis, p. e. I-214 , p. e. 561/41 ) ، با استفاده از دو سطح رطوبت کیک 7 و10 درصد و سه سطح حرارت پرس180، 200 و220 درجه سانتیگراد ساخته شدند. در کلیه تیمارها، دانسیته تخته ها 7/0 گرم بر سانتیمتر مکعب، زمان پرس 8 دقیقه و نوع چسب مصرفی؛ فنل فرمالدئید به میزان 7 درصد وزن خشک چوب بود. خواص مکانیکی و فیزیکی تخته‌های آزمونی، بر پایۀ استاندارد اروپایی (EN 300) جهت تولید تخته تراشه جهت دار نوع 1 و نوع 2 مورد ارزیابی قرار گرفت. نتایج حاصل نشان داد که افزایش رطوبت کیک اثر بسیار معنی‌داری بر افزایش ویژگی‌های خمشی تخته‌ها داشت به طوری که بالاترین مدول گسیختگی در رطوبت کیک 10 درصد و حرارت پرس 220 درجه سانتیگراد و بالاترین مدول الاستیسیته در رطوبت کیک 10 درصد و حرارت پرس 180 درجه سانتیگراد به دست آمد. افزایش حرارت پرس نیز اثر بسیار معنی داری در افزایش مدول گسیختگی تخته‌ها و همچنین اثر معنی داری در کاهش واکشیدگی ضخامت 24 ساعت تخته ها داشت. کمترین واکشیدگی ضخامت 24 ساعت در رطوبت کیک 7 درصد و حرارت پرس 220 درجه سانتیگراد به دست آمد. بالاترین چسندگی داخلی در رطوبت کیک 7 درصد و حرارت پرس 200 درجه سانتیگراد به دست آمد.در مجموع در تمامی حالتها خصوصیات تخته‌های تولید شده بیشتر از حد استاندارد مورد نیاز بود.}, keywords_fa = {تخته تراشه جهت دار,صنوبر,کلن,زمان پرس,رطوبت کیک,فنل فرمالدیید}, url = {https://ijwpr.areeo.ac.ir/article_106766.html}, eprint = {https://ijwpr.areeo.ac.ir/article_106766_6009c4181949ec02753245b5f64b6e43.pdf} } @article { author = {Nazaneghad, Noradin and Mosavi, seid najeh and Zabihzadeh, Seid Majid}, title = {Comparing the performance of cationic starch, corn and tapioca to improve the strength characteristics of paper from old corrugated containers}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {31}, number = {4}, pages = {662-670}, year = {2016}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2016.106289}, abstract = {Abstract The aim of this study is investigate the effect of Tapioca and Corn cationic starch on the mechanical characteristics of paper from old corrugated containers. The paper recycling decrease its properties and affected on the paper quality. For promoting these fibers may be effective the use of different treatments. Cationic starch is effective treatment for recycled fibers Promotion. In this study, the cationic starch of Tapioca and Corn, each at three different levels 0.5, 1 and 1.5 % and comparison with samples (without cationic stretch). Hand sheets with a grammag of 120 g/m2 were made and their strength properties were measured. As well as, the absorption rates of two kinds of starch on the pulp were calculated using the Acid- Phenol method. The results indicated that the use of 1.5% of Tapioca starch and 1% Corn starch had an optimum effect in increasing the strength of the produced paper. Concerning the comparison of these different types of starch, the tapioca starch was more effective than the corn starch.}, keywords = {cationic starch,OCC,recycling,Tapioca,Corn}, title_fa = {مقایسه عملکرد نشاسته کاتیونی ذرت و تاپیوکا در بهبود ویژگی های مقاومتی کاغذ حاصل از کارتن های کنگره ای کهنه}, abstract_fa = {هدف از این تحقیق بررسی تاثیر نشاسته کاتیونی ذرت و تاپیوکا بر ویژگی‌های مقاومتی کاغذ ساخته شده از کارتن‌های کنگره‌ای کهنه می‌باشد. در اثر بازیافت کاغذ ویژگی‌های آن افت کرده و بر کیفیت مورد نظر کاغذ تاثیر منفی می‌گذارد. به کارگیری تیمار‌های مختلف می‌تواند در ارتقاء این الیاف موثر واقع شود. از تیمار‌های موثر در ارتقاء الیاف بازیافتی، استفاده از نشاسته کاتیونی می‌باشد. در این بررسی از نشاسته کاتیونی ذرت و تاپیوکا هر یک در 3 سطح 5/0، 1 و 5/1 درصد استفاده و با نمونه های شاهد( فاقد نشاسته کاتیونی) مقایسه شد. کاغذ دست‌ساز با جرم پایه 120 گرم بر متر‌مربع ساخته و ویژگی‌های مقاومتی آن اندازه‌گیری شد. همچنین میزان جذب نشاسته‌ها بر روی خمیر‌کاغذ با استفاده از روش فنول- اسید محاسبه گردید. نتایج مشخص نمود که مصرف 5/1 درصد نشاسته تاپیوکا و 1 درصد ذرت در اغلب موارد تاثیر بهینه را در افزایش مقاومت کاغذهای حاصله داشته است. همچنین در مقایسه دو نشاسته، تاپیوکا عملکرد بهتری داشته است.}, keywords_fa = {نشاسته کاتیونی,بازیافت,OCC,تاپیوکا,ذرت}, url = {https://ijwpr.areeo.ac.ir/article_106289.html}, eprint = {https://ijwpr.areeo.ac.ir/article_106289_cd2edb507834a783d2d92c7bf6b21b3a.pdf} } @article { author = {dastoorian, foroogh and Layeghi, Mohammad and Ebrahimi, Ghanbar and Tajvidi, Mehdi and Zabihzadeh, Seid Majid}, title = {Creep rupture behavior of a bagasse fiber-polypropylene composite}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {31}, number = {4}, pages = {671-683}, year = {2016}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2016.106764}, abstract = {In the present study, creep rupture behavior of a bagasse fiber- polypropylene composite was investigated. Two accumulated damage model (EDRM and Wood) and an energy based failure model (R-W) were adopted to describe the load duration influence on the studied composite. Results have shown that at very high stress levels, the EDRM and Wood models underestimated and overestimated the time to failure than static value respectively. This was attributed to the difference between application of static loading and creep loading. Findings indicated that the all three models were able to describe the creep rupture behavior of the studied composite and among this; the Wood model has shown a better fitting with experimental data, statistically. Based on findings in the present research, it can be concluded that the R-W model was more conservative in predicting time to failure in comparison with the two other models, and the reason can be attributed to the difference between failure criteria in energy based models and accumulated damage models. Results also showed that with increasing stress levels, the secondary stage of creep will shorten and at high stress level, the tertiary stage of creep will be more dominant}, keywords = {composites,creep rupture,three stages of creep,accumulated damage models,energy based failure models}, title_fa = {رفتار گسیختگی خزش ماده مرکب الیاف باگاس- پلی‌پروپیلن}, abstract_fa = {در این مطالعه رفتار گسیختگی خزش ماده مرکب الیاف باگاس- پلی‌پروپیلن مورد بررسی قرار گرفت. برای توصیف اثر دوام بار بر روی ماده مرکب مورد مطالعه، دو مدل تخریب تجمعی (EDRM و Wood)، و یک مدل شکست بر پایه انرژی (R-W)، مورد استفاده قرار گرفته‌اند. نتایج نشان داد که مدل EDRM در سطح تنش بسیار بالا، زمان شکست را کمتر از مقدار استاتیکی و مدل Wood، زمان شکست را بیشتر از مقدار حاصل از آزمون استاتیک برآورد می‌کند. علت این امر به تفاوت در نحوه اعمال بار در بارگذاری استاتیکی و بارگذاری خزشی نسبت داده شد. نتایج نشان داد که هر سه مدل قادر بودند رفتار گسیختگی خزش ماده مرکب مورد مطالعه را به خوبی توصیف کنند و در این بین مدل Wood از لحاظ آماری برازش بهتری را بر روی داده‌های تجربی نشان داده است. بر اساس یافته‌های تحقیق حاضر می‌توان نتیجه گرفت که مدل R-W در پیش بینی زمان شکست، نسبت به دو مدل دیگر محافظه-کارانه‌تر عمل می‌کند و علت این امر را می‌توان به تفاوت در معیار شکست در مدل‌های بر پایه انرژی یا معیار شکست در مدل‌های تخریب تجمعی نسبت داد. همچنین نتایج نشان داد که با افزایش سطح تنش مرحله دوم خزش کوتاه‌تر می‌شود و در سطوح تنش ‌بالا، مرحله سوم خزش غالب است.}, keywords_fa = {ماده مرکب,گسیختگی خزش,مراحل سه‌گانه خزش,مدل‌های تخریب تجمعی,مدل‌های شکست بر پایه انرژی}, url = {https://ijwpr.areeo.ac.ir/article_106764.html}, eprint = {https://ijwpr.areeo.ac.ir/article_106764_4b655b8407f0fad19f25cee785b5fabf.pdf} } @article { author = {Rangavar, Hossein and Nourbakhsh, Amir and Haji hatmlo, Saeid}, title = {The Effect of Nano-Wollastonite on Physical and Mechanical Properties of Wood Plastic Composites Made With Sunflower Stem Waste and Alder}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {31}, number = {4}, pages = {684-694}, year = {2016}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2016.107021}, abstract = {The effects of nano-wollastonite on physical and mechanical properties of wood plastic composites made with dried sunflower stalks and alder wood flour, were studied. Five levels of sunflower stalk flour in ratio of the mass wood dry flour containing 0, 25, 50, 75 and 100 percent and nano-wollastonite Powder in three levels, 3, and 5% were considered as variables of the study. Physical and mechanical properties, perpendicular to the screw strength, bending strength, modulus of elasticity, water absorption and thickness swelling after 2 and 24 soaking hours in water were measured in accordance with the standard DIN- EN. In order to examine the intersection of wood and polymer as well as distribution patterns of nanoparticles in the polymer matrix microscopic photos were taken. The results showed that by increasing of sunflower stalk flour in the mixing with wood flour up to 25% increased resistance to screw withdrawal and up to 50 percent increase in flexural strength and modulus of elasticity of wood-plastic composites, respectively. Sunflower stalk flour mixed with alder wood flour increased water absorption and thickness swelling after 2 and 24 hours immersion in water. The use of nano-wollastonite up 5% in relation to the total mass of all the boards improved the physical and mechanical properties of wood-polymer composite.}, keywords = {Keywords: sunflower stalk,WOOD-PLASTIC COMPOSITES,nano-wollastonite,PHYSICAL AND MECHANICAL PROPERTIES}, title_fa = {تاثیر نانو ولاستونیت بر خواص فیزیکی و مکانیکی چوب پلاستیک ساخته شده با ساقه آفتابگردان و چوب توسکا}, abstract_fa = {در این پژوهش تاثیر نانو ولاستونیت بر خواص فیزیکی و مکانیکی چندسازه چوب پلاستیک ساخته شده با پودر پسماند ساقه آفتابگردان و چوب توسکا مورد بررسی قرار گرفت. پودر ساقه آفتابگردان مورد استفاده نسبت به جرم خشک پودرچوب در پنج سطح صفر، 25، 50، 75 و 100 درصد و نانو ولاستونیت بصورت پودر در سه سطح صفر، 3 و 5 درصد به عنوان عوامل متغیر این تحقیق در نظر گرفته شدند. خواص فیزیکی و مکانیکی چندسازه شامل مقاومت به پیچ عمود بر سطح، مقاومت خمشی، مدول الاستیسیته، جذب آب و واکشیدگی ضخامت پس از 2 و 24 ساعت غوطه‌وری در آب مطابق با استاندارد EN DIN-اندازه گیری گردید. به منظور بررسی فصل مشترک چوب و پلیمر و همچنین نحوه پراکنش و توزیع نانو ذرات ولاستونیت در ماتریس پلیمری عکسهای میکروسکوپی تهیه گردید. نتایج نشان داد که با افزایش نسبت اختلاط پودر ساقه آفتابگردان به پودر چوب تا سطح 25 درصد سبب افزایش مقاومت به پیچ عمود بر سطح و تا سطح 50 درصد باعث افزایش مقاومت خمشی و مدول الاستیسیته چندسازه چوب پلاستیک گردید. استفاده از پودر ساقه آفتابگردان در مخلوط با پودر چوب توسکا سبب افزایش میزان جذب آب و واکشیدگی ضخامت 2 و 24 ساعت غوطه وری در آب شد. استفاده از نانو ولاستونیت تا سطح 5 درصد نسبت به جرم کل تخته سبب بهبود کلیه خواص فیزیکی و مکانیکی چند سازه چوب پلاستیک گردید.}, keywords_fa = {واژه‌های کلیدی: ساقه آفتابگردان,چندسازه چوب پلاستیک,نانو ولاستونیت,خواص فیزیکی و مکانیکی}, url = {https://ijwpr.areeo.ac.ir/article_107021.html}, eprint = {https://ijwpr.areeo.ac.ir/article_107021_3162347a13002ddfe3ec8f6b4e7116c4.pdf} } @article { author = {asadi, fatemeh and Nazarneghad, Noradin and Asadpoor atoeei, Ghasem}, title = {Preparation of nano-cellulose from cladophora, a fibrous algae, utilizing it at improving the strength properties of CMP pulp.}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {31}, number = {4}, pages = {695-702}, year = {2016}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2016.106290}, abstract = {Nowdays, algae considering marine ecosystem are regarded as producers and the first continuum that receives solar energy. Hence, they ensure the needed energy for the aquatic organism living. In global herbal division, algae have 1800 genus and 21000 types. Because of their presence in air rather than underground water, algae allocate larger arena to themselves in comparise to other herbage. Based on accomplished studies, it is rated that algae have more than 7000 types in terms of biological diversity. Algae are used a lot. They are consumed in food industry, dung preparation, medicinal consumption and etc. In this study the green algae nanocellulose was used to improve CMP resistance.For the preparation of pure cellulose, algae samples initially affected the soda process and then were affected by bleaching sequence.. Next, the obtained cellulose has been converted to Nano-cellulose by using ultrasonic method. Nano-cellulose from cladophora algae was mixed with CMP in the ratios of 2, 5 and 8 percent. Finally, handmade paper was made and its resistive (strengh) properties were studied and compared with the pure hardwood CMP pulp. The results revealed that 8% treatment group had the highest density, tensile strength, burst strength, and control group had the lowest amount. Furthermore, the highest tear strength was related to control group; while, the lowest tear strength was for 8% treatment group.}, keywords = {Ultrasonic treatment,Cladophora green algae,Strength properties,CMP paper,Nano-cellulose}, title_fa = {تهیه نانو سلولز از جلبک رشته ای کلادوفورا و استفاده از آن جهت بهبود ویژگی های مقاومتی خمیر CMP}, abstract_fa = {امروزه جلبک‌ها از نظر بوم سامانه‌های دریایی به عنوان تولیدکنندگان و اولین زنجیره دریافت انرژی از خورشید محسوب می‌شوند. به این صورت تضمین کننده‌ی انرژی بسیاری از آبزیان برای زندگی هستند. در تقسیمات جهانی گیاهی، جلبک‌ها 1800 جنس و 21000 گونه دارند. جلبک‌ها به‌دلیل حضورشان در هوا تا آب‌های زیرزمینی، عرصه وسیع‌تری را در مقایسه با سایر رستنی‌ها به خود اختصاص می‌دهند. بر اساس مطالعات انجام شده، تنوع زیستی جلبک‌ها در ایران بیش از 7000 گونه برآورد می‌گردد. جلبک‌ها دارای مصارف بسیار زیادی از جمله‌ درصنایع غذایی ،تهیه ی کود ، مصارف دارویی و غیره می‌باشد. در این تحقیق از نانو‌سلولز جلبک سبز کلادوفورا جهت بهبود مقاومتهای خمیر CMP استفاده شده است. جهت انجام این کار از جلبک مذکور با استفاده از فرآیند سودا و سپس رنگبری سلولز خالص تهیه شد..سپس سلولز حاصله با روش التراسونیک به نانو‌سلولز تبدیل شد. نانو‌سلولز جلبک کلادوفورا در نسبت های 2 ، 5 و 8 درصد با خمیرCMP مورد اختلاط قرار گرفت. در نهایت کاغذ دست‌ساز تهیه و ویژگی های مقاومتی آن با خمیر خالص CMP حاصل از چوب پهن‌برگان مورد بررسی و مقایسه قرار گرفت. نتایج نشان داد که تیمار 8 درصد بیشترین دانسیته، مقاومت به کشش، مقاومت به ترکیدن و تیمار شاهد کمترین مقدار را داشته است. همچنین بیشترین مقاومت به پاره‌شدن مربوط به تیمار شاهد بوده در حالیکه کمترین مقاومت به پاره‌شدن مربوط به تیمار 8 درصد بوده است.}, keywords_fa = {تیمار فراصوتی,جلبک سبز کلادوفورا,خواص مقاومتی,کاغذ CMP,نانو‌سلولز}, url = {https://ijwpr.areeo.ac.ir/article_106290.html}, eprint = {https://ijwpr.areeo.ac.ir/article_106290_01aa2ad1074ae258013ad0ffb31bcfa2.pdf} }