@article { author = {Hosseinzadeh, Abdolrahman and Nourbakhsh, Amir and Kargarfard, Abolfazl and Golbabaei, Fardad and Nazeryan, Morteza}, title = {THE SUITABILITY OF TWO- YEAR- OLD POPLAR CLONES FOR PRODUCTION OF PARTICLEBOARD}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {19}, number = {شماره 1}, pages = {1-24}, year = {2004}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2004.117549}, abstract = {Decreasing availability of raw material for Iranian wood industries and the need to conserve our limited natural forests initiated research concerning the utilization of fast-growing species in particleboard production. The objective of this study was to investigate the possibility of particleboard production from wood of two- year- old coppices of 17 experimental populus clones grown under intensive culture in the "Alborz Research Center" near Tehran. The furnish contained mixture of stem and branch wood with bark used to make 51 sample boards (3 board from each clone). Modulus of elasticity (MOE), modulus of rupture (MOR), internal bond strength (IB), thickness swelling and water absorption of the specimens were tested. The results indicate that sample boards made from Populus euramericana costanzo and populus euramericana 561.41 had significantly the highest MOR and MOE. But there was no significant differences in the internal bonding strength between different clones, while, those sample boards made from populus nigra betulifolia and Populus nigra nivea showed significantly the lowest percentages of thickness swelling. The average physical and mechanical properties of the particleboard samples produced from two- year- old coppices of poplar clones compared favourably to boards made from natural grown beech wood. Therefore, using UF resin, particleboard with acceptable quality particleboards can be produced from two- year- old poplar clones.}, keywords = {Particleboard,UF RESIN,PHYSICAL AND MECHANICAL PROPERTIES,TWO- YEAR- OLD POPLAR}, title_fa = {ویژگیهای تخته خرده چوب ساخته شده از چوب کلن های مختلف صنوبر تولید شده در دوره بهره برداری دو ساله}, abstract_fa = {در این تحقیق ویژگیهای تخته خرده چوب ساخته شده از چوبهای تولیدی 17 کلن صنوبر در دوره بهره برداری کوتاه مدت دو ساله مورد بررسی قرار گرفته است. از هر کلن (تیمار) سه تخته (در مجموع 51 تخته) با استفاده از چسب اوره – فرم آلدیید در شرایط یکسان ساخته شده، خصوصیات فیزیکی و مکانیکی آنها اندازه گیری و در قالب طرح آزمایشی فاکتوریل کاملا تصادفی متعادل با یک متغیر و با استفاده از آزمون دانکن (DMRT) مورد مقایسه و تجزیه و تحلیل آماری قرار گرفته است. نتایج بدست آمده نشان میدهد که تخته های ساخته شده از چوب کلنهای Populus euramericana costanzo وPopulus euramericana 561.41 دارای بیشترین میانگین مقاومت خمشی و کلنهای Populus deltoides 72.51وPopulus euramericana triplo دارای کمترین مقاومت خمشی هستند. کلنهای Populus ciliata، Populuseuramericana 561.41 و Populus deltoides 77.51 بیشترین مدول الاستیسیته و کلنهایPopulus deltoides 72.51 وPopulus alba 44.9 کمترین میانگین مدول الاستیسیته را داشته اند. همچنین کلنهای Populus euramericana 561.41 وPopulus alba 58.57 دارای بیشترین میانگین چسبندگی داخلی و کلنهای Popalus ciliata و Populus deltoides 72.51کمترین چسبندگی داخلی را دارند.کلنهای Populus deltoides وPopulus ciliata بیشترین مقدار جذب آب پس از 24 ساعت و کلنهای Populus alba nivea وPopulus euramericana 561.41 کمترین مقدار جذب آب بعد از 24 ساعت غوطه وری در آب را داشته اند. به علاوه کلنهای Populus deltoides 42.51 و Populus ciliata بیشترین واکشیدگی ضخامت و کلنهای Populus alba nivea وPopulus nigra betulifolia کمترین مقدار واکشیدگی ضخامت بعد از 2 ساعت غوطه وری در آب را از خود نشان داده اند.   }, keywords_fa = {تخته خرده چوب,صنوبر,دوره بهره برداری کوتاه مدت دو ساله,چسب اوره فرم آلدیید,ویژگیهای فیزیکی و مکانیکی}, url = {https://ijwpr.areeo.ac.ir/article_117549.html}, eprint = {https://ijwpr.areeo.ac.ir/article_117549_1d0970c40b4fb0d99c6b0fd2342b229d.pdf} } @article { author = {Jahan latibari, Ahmad and Golbabaei, Fardad and Amini, Mohammad reza}, title = {INVESTIGATION ON TRACHIEDS CHARACTERISTICS OF PINUS TEADA}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {19}, number = {شماره 1}, pages = {25-48}, year = {2004}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2004.117550}, abstract = {Pinus teada, which was planted in Pelembera region, shows promising both in growth rate and adaptability. Even though the fiber geometry of P. teada wood in its native growth region is excellent, but for utilization of this wood in pulping, the knowledge of its technological characteristics especially fiber geometry is required.Two trees of this species were randomly selected from Pelembera forests plantation in Gilan and after felling were cut in smaller bolts and transferred to wood &paper research laboratory, research institute of forests and rangelands. Five cross-sections with the thickness of 15 cm were cut from each tree and the cross-sections were used for selection of samples. Fiber geometry measurement samples were prepared from every five annual rings and from each sample, springwood (early wood) and summer wood (late wood) sample were cut separately. Preparations of fiber geometry samples were according to procedure developed by Franklin (1954) and from each sample the dimension of 30 complete and unbroken trachieds was measured.Trachied length, diameter, cell wall thickness and lumen diameter was measured for different elevation in tree and different growth rings in cross-section.Dimension of 3,00 trachieds were measured totally.Average trachied length, diameter, lumen diameter and cell wall thickness of early wood were measured at 3.65mm, 38.97 mm, 28.94 mm and 3.72 mm respectively. Related values for late wood is as follow: trachied length 3.84mm; diameter, 35.54 /lm; lumen diameter, 22.96 mm; and cell wall thickness, 6.29  mn. Average annual growths were measured at 5.66 mm and late wood percentage at 24.13. Felting, flexibility and runkel coefficients were calculated at 97.96, 73.48, and 26.74 respectively. The result of this study indicates that all measured properties increases with increasing the height of tree and from center (pith) toward outer regions (bark). However all the measured values decreased at highest as well as outer locations.Statistical analysis indicated that the difference in measured properties at different heights of trees from center to the bark is significantly different at 1% level.}, keywords = {PINUS TEADA,TRACHIED LENGTH,DIAMETER,LUMEN DIAMETER,CELL WALL THICKNESS,EARLY WOOD AND LATE WOOD}, title_fa = {بررسی تغییرات ابعاد تراکئید کاج تدا از جنگلکاریهای منطقه پیلمبرا}, abstract_fa = {کاج تدا (Pinus Teada) از سوزنی برگانی است که طی حدود چهار سال گذشته در ایران کشت شده و به عنوان یک منبع چوبی الیاف بلند جهت تولید کاغذ مورد توجه است. با توجه به نقش ابعاد الیاف در ویژگیهای کاغذ این تحقیق به منظور تعیین تغییرات ابعاد این گونه چوبی و تعیین امکان استفاده از آن در صنایع چوب به انجام رسیده است.دو درخت از منطقه پیلمبرا در گیلان انتخاب و پس از قطع و استحصال به آزمایشگاه علوم چوب و کاغذ دانشکده کشاورزی دانشگاه آزاد اسلامی کرج حمل شد. از هر درخت تعداد 5 دیسک تهیه و از هر دیسک نیز در فاصله هر 5 دایره رویشی از مغز به سمت پوست دو نمونه تراشه به تفکیک چوب آغاز و پایان جدا گردید. پس از آماده سازی الیاف قبل روش فرانکلین (1954) از هر نمونه تعداد 30 عدد تراکئید سالم و بدون شکستگی و پیچیدگی انتخاب شده و به کمک میکروسکوپ تحقیقاتی تراکئید شامل طول تراکئید، قطر تراکئید، قطر حفره تراکئید و ضخامت دیواره سلولی اندازه گیری شد و تغییرات آنها با توجه به سه عامل ارتفاع، دایره رویشی و چوب آغاز و پایان مورد مطالعه قرار گرفت. میانگین کلی طول تراکئید، قطر تراکئید، قطر حفره تراکئید و ضخامت دیواره سلولی 3000 تراکئید اندازه گیری شده برای گونه فوق به ترتیب برابر با3.65 میلیمتر، 38.97، 28.94 و 5.01 میکرون محاسبه شد. طول تراکئید، قطر تراکئید، قطر حفره تراکئید و ضخامت دیواره سلولی چوب آغاز به ترتیب برابر با 3.40 میلیمتر، 42.34، 34.87 و 3.72 میکرون و میانگین این ویژگیها برای چوب پایان نیز به ترتیب 3.84 میلیمتر، 35.54، 22.96 و 6.29 میکرون بدست آمد. رویش سالیانه (رویش قطری) 5.66 میلیمتر، چوب پایان 24.13%، ضریب در هم رفتگی 94.96%، ضریب نرمش 73.48 و ضریب رونکل 26.47 تعیین گردید.با در نظر گرفتن سه عامل ارتفاع، دایره رویشی و چوب آغاز و پایان مشخص شد که با افزایش ارتفاع درخت و همچنین افزایش فاصله از مغز به سمت پوست کلیه ویژگیهای آناتومیکی از قبیل طول تراکئید، قطر تراکئید، قطر حفره تراکئید و ضخامت دیواره سلولی افزایش می یابد. ولی در بالاترین ارتفاع و همچنین دوایر رویشی نزدیک پوست از میزان افزایش ابعاد کاسته می گردد. تجزیه و تحلیل آماری نشان داد که میانگین هر چهار ویژگی اندازه گیری شده الیاف نسبت به تغییر ارتفاع از سطح زمین به بالا و تغییر دایره رویشی از مغز به سمت پوست در سطح 1% با هم اختلاف معنی داری دارند.}, keywords_fa = {کاج تدا,طول تراکئید,قطر تراکئید,قطر حفره تراکئید و ضخامت دیواره سلول}, url = {https://ijwpr.areeo.ac.ir/article_117550.html}, eprint = {https://ijwpr.areeo.ac.ir/article_117550_c3ca9b4ca67aa7ced0e81ad7b5e3a2d6.pdf} } @article { author = {Nourbakhsh, Amir and V.Kokta, Bohuslav and Hosseinzadeh, Abdolrahman and Jahan latibari, Ahmad and Kargarfard, Abolfazl}, title = {THE COMPARATIVE OF EFFECTS OF CELLULOSIC MATERIALS IN DIFFERENT LEVELS OF MAPP IN WOOD FIBER- FLOUR/ POLYPROPYLENE COMPOSITES}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {19}, number = {شماره 1}, pages = {49-68}, year = {2004}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2004.117561}, abstract = {This study investigates the effect of maleic anhydride polypropylene (MAPP) addition as a coupling agent at four levels and also the type of cellulosic materials as a reinforcing component on processing and mechanical properties of modified Populus deltoides fiber and flour/ polypropylene composites.The results indicate that the interfacial bond between reinforcing-fiber/ flour and the matrix show great influence on the mechanical properties of composites. Furthermore it has been demonstrated that the addition of coupling agent during processing significantly improves the mechanical properties of fiber/ flour polypropylene composites. The results of this investigation indicates that the highest the mechanical properties of composites are as follow; The mechanical properties of the poplar fiber with 2% MAPP is higher than poplar flour without MAPP, which proves that the addition of functional group C=O acts as a good bonding agent. The notched Impact Izod strength value of poplar fiber with 2% MAPP is less than pure PP. But it is higher than other treatments. The results indicate that the interfacial bond between reinforcing fibers and flour with polymer matrix modified MAPP play a significant role in improving the measured mechanical properties of the composites.}, keywords = {composites,WOOD FIBER,WOOD FLOUR,MAPP,IMPACT STRENGHT,TENSILE STRENGHT}, title_fa = {مقایسه اثر مواد لیگنوسلولزی در سطوح مختلف انیدریدمالئیک پلی پروپیلنی (MAPP) در چند سازه های الیاف و آرد چوب / پلی پروپیلن}, abstract_fa = {این تحقیق اثر افزودن انیدریدمالئیک پلی پروپیلنی (MAPP) به عنوان عامل جفت کننده در چهار سطح، نوع ماده سلولزی به عنوان تقویت کننده در فرآیند و اصلاح کنندگی آنها را بر ویژگیهای مکانیکی چند سازه های مواد سلولزی/ پلیپروپیلن مورد توجه قرار داده است. نتایج این بررسی نشان میدهد که اتصال سطح مشترک میان الیاف و آرد چوب و ماتریس اثر زیادی بر ویژگیهای مکانیکی چند سازه داشته است. همچنین مشخص گردید که اضافه کردن عامل جفت کننده در فرآیند به طور واضح باعث بهبود ویژگیها شده است. براساس نتایج بدست آمده، بهترین ویژگیهای مکانیکی چند سازه الیاف و آرد چوب/ پلیپروپیلن به شرح زیر میباشد: - ویژگیهای مقاومت به ضربه فاقدار و مقاومت کششی چند سازه ساخته شده با الیاف چوب صنوبر در سطح 2 درصد عامل جفت کننده (MAPP) بالاتر از چند سازه ساخته شده با آرد چوب صنوبر بدون حضور عامل جفت کننده میباشد. - مقاومت به ضربه فاقدار در چند سازه ساخته شده با الیاف چوب صنوبر در سطح 2 درصد عامل جفت کننده (MAPP) کمتر از پلیپروپیلن خالص بوده است، ولی از سایر تیمارهای مورد بررسی بیشتر می باشد. به طور کلی اتصال سطح مشترک میان الیاف / آرد چوب و ماتریس پلیمر با انیدریدمالئیک پلیپروپیلنی (MAPP) نقش مهمی بر بهبود ویژگیهای مقاومت به ضربه فاقدار و مقاومت کششی چند سازه الیاف و آرد چوب صنوبر/ پلیپروپیلن داشته است.}, keywords_fa = {چند سازه,الیاف و آرد سلولزی,انیدریدمالئیک پلیپروپیلنی (MAPP),مقاومت به ضربه فاقدار و مقاومت کششی}, url = {https://ijwpr.areeo.ac.ir/article_117561.html}, eprint = {https://ijwpr.areeo.ac.ir/article_117561_f870e1656e15a3d8f9296eb078a2fcfc.pdf} } @article { author = {Mahdavi, Saeed and Hosseinzadeh, Abdolrahman and Familian, Hossein and habibi, masoudreza}, title = {INVESTIGATION ON RELATION OF FIBER DIMENSION AND WOOD DENSITY WITH-AGE AND RING WIDTH IN E.CAMALDULENSIS DEHNH}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {19}, number = {شماره 1}, pages = {69-98}, year = {2004}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2004.117562}, abstract = {Cross sectional disks were cut at breast height from three 17-year-old trees of E.camaldulensis grown in Pasand research station in Mazandaran province. Ring width, wood density, and fiber dimension were measured for each two rings from pith to the bark. Overall average disks, fiber length, fiber width, lumen diameter, and cell wall thickness were measured at 758, 15.93, 8.63, and 3.65 micrometer respectively. Mean values for the oven dry and basic. Density was 0.708 g/cm3 and 0.552 g/cm3. Cross sectional \ growth rate and wood production for the trees were measured at 11.1 mm and 12.3 m3/ha./year respectively. Chemical compositions of the wood consist or cellulose, lignin, extractives (in acetone soluble) and ash were measured at 47.44%, 30.87%, 6.96%, and 0.27% respectively. The result showed that E.camaldulensis is classified as short fiber hardwood with low frequency. Fiber dimensions and density slightly increased from pith to the bark. There was high significant correlation between cell wall thickness and density, while; there was no significant correlation between ring width and the others. Among the properties studied, cell wall thickness and fiber length showed the most variations.}, keywords = {E.CAMALDULENSIS,RING WIDTH,FIBER DIMENSION,Density,chemical composition}, title_fa = {بررسی همبستگی ابعاد الیاف و جرم مخصوص با میزان رویش قطری و سن در چوب اکالیپتوس E.camaldulensis Dehnh}, abstract_fa = {سه درخت 17 ساله اکالیپتوس camaldulensis از ایستگاه تحقیقات پاسند واقع در نزدیکی بهشهر قطع شد. برای اندازه گیری ابعاد فیبر، میزان رویش قطری سالیانه، جرم مخصوص و ترکیب شیمیایی، از ارتفاع برابر سینه این درختان دیسکهای چوبی تهیه شد. اندازه گیری سه ویژگی اول، برای هر دو دایره سالیانه و از مغز درخت به طرف پوست انجام شد و همبستگی آنها با هم و نیز سن درخت مورد بررسی قرار گرفت. میانگین ابعاد فیبر درختان شامل طول و قطر فیبر، قطر حفره سلولی و ضخامت دیواره سلولی به ترتیب 758، 15.93، 8.63 و 3.65 میکرومتر محاسبه شد. میانگین جرم مخصوص خشک و بحرانی نیز به ترتیب 0.708 و 0.552 گرم بر سانتیمتر مکعب بدست آمد. میزان متوسط رویش قطری سالیانه درختان با فاصله کاشت 5×5، 11.1 میلیمتر با تولید چوب خشک 12.38 متر مکعب در هکتار در سال تعیین شد. میانگین ترکیب شیمیایی شامل سلولز، لیگنین، خاکستر و مواد استخراجی محلول در استن به ترتیب 47.44، 30.87،0.26 و 6.96 درصد محاسبه شدند. نتایج این بررسی نشان داد که این گونه در میان پهن برگان از الیاف کوتاهتری برخوردار است و پراکنش طولی آنها کم است. ابعاد فیبر و جرم مخصوص چوب با افزایش سن درختان (از مغز به طرف پوست) از روند افزایشی با شیب ملایم برخوردار است. تغییرات ضخامت دیواره سلولی با جرم مخصوص چوب دارای همبستگی زیاد میباشد، در حالی که بین میزان رشد قطری و سایر خواص چوب (مثل جرم مخصوص و ابعاد فیبر) همبستگی معنی داری وجود ندارد. در میان خصوصیات مختلف بررسی شده چوب اکالیپتوس camaldulensis، ضخامت دیواره سلولی و نیز طول فیبر بیشترین تغییرات را در میان درختان و نیز دوایر رویش سالیانه آنها داشتند.  }, keywords_fa = {اکالیپتوس camaldulensis,دایره رویش,ابعاد فیبر,جرم مخصوص,ترکیب شیمیایی}, url = {https://ijwpr.areeo.ac.ir/article_117562.html}, eprint = {https://ijwpr.areeo.ac.ir/article_117562_6cd31d61f5379d7293b06b945a32d444.pdf} } @article { author = {Arab tabar firoz jaei, Habib alah and Reza nezhad, Ali and Hosseinzadeh, Abdolrahman}, title = {PRESERVATIVE TREATMENT OF GREEN POPLAR POLES BY USING TIRE -TUBE METHOD}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {19}, number = {شماره 1}, pages = {97-114}, year = {2004}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2004.117563}, abstract = {In this study, green round poles of Populus nigra L. var. italica were treated with Celcure by using Tire - Tube method. After felling and sizing trees, thick - end of poles (about 15 cm.) were debarked and a section of tire inner Tube was fastened around the debarked end of the fresh - cut poles and bound tightly with rubber bands and the upper end of the tube was connected to the elevated solution container. Then the poles installed on slope and let them to absorb the solution. The results showed that sapwoods were completely penetrated but hartwood less after 8-24 hrs.}, keywords = {POLES,PRESERVATION,IMPREGNATION,CELCURE,BOUCHERIE,TIRE TUBE METHOD}, title_fa = {بررسی اشباع چوب تبریزی (Populus nigra L. var. italica) به روش تیوب لاستیکی}, abstract_fa = {در این بررسی چوبهای سبز و تازه قطع شده تبریزی (Populus nigra L. var. italica) به روش تیوب لاستیکی اشباع گردیدند. پس از قطع درختان و اندازه بری چوب، بلافاصله فقط سر قطور تیر به طول حدود 15 سانتیمتر پوست کنی شدند. یک سر تیوب لاستیکی در قسمت پوست کنی شده نیز قرار گرفته و با نوار لاستیکی محکم بسته شد. تیرها در حالت شیب دار قرار گرفتند به طوری که سر قطور تیرها حداقل 45 سانتیمتر بالاتر از سر باریک آن قرار داشتند. ماده حفاظتی محلول در آب سلکور (ACC) که حاوی اسید کرومیک با نسبت 1.7 درصد، سولفات مس با نسبت 50% و دی کرومات سدیم با نسبت 48.3% بود با غلظت 5% آماده و در داخل تیوب لاستیکی ریخته شد. ابتدا شیره گیاهی (آب چوب) از سر باریک تیر جاری، بعد ماده حفاظتی از آن جاری شد. زمانی که سطح ماده حفاظتی داخل تیوب، از مقطع تیر کمی پایین تر آمده بود، تیوب از سر تیر جدا شده و تیر در حالت افقی (بدون شیب) قرار گرفت. نتایج این بررسی نشان داد که چوب برون تبریزی به طور کامل و چوب درون آن تقریبا تا حدود کمی اشباع گردیدند. مدت زمان اشباع در تیرهایی که درختان آنها خوب آبیاری شده و دارای تنه راست و کم گره باشند، کمتر است.}, keywords_fa = {تیر,ماده حفاظتی,سلکور,اشباع چوب,روش بوشری و تیوب لاستیکی}, url = {https://ijwpr.areeo.ac.ir/article_117563.html}, eprint = {https://ijwpr.areeo.ac.ir/article_117563_bd4e55f3a3c6cd957140c63291011d58.pdf} } @article { author = {Reza nezhad, Ali and Arab tabar firoz jaei, Habib alah and Hosseinzadeh, Abdolrahman}, title = {RESISTANCE OF SOME IRANIAN HARDWOODS AGAINST MARINE BORERS IN BOSHEHR PORT COAST (PERSIAN GULF)}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {19}, number = {شماره 1}, pages = {115-131}, year = {2004}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2004.117564}, abstract = {Four hardwood species including: Alder (Alnus subcordata), Oriental plane (Platanus orientalis), Eucalyptus camaldulensis and Babul (Acacia arabica) were treated with Creosote and Celcure. The dimension of samples was 20 x 7.5 x 2 cm. Both preservative treated and untreated samples were placed in seawater (Boshehr in Persian Gulf) according to IRG/WP-4432 (1985). After 9, 15, 24, 29, 38, 47, 53, 58 and 64 months, the samples were inspected according with recommendation of IRG/WP-4432(1985) and ASTM D- 240. All the control samples (untreated wood) of Alder and Oriental plane over 9 months, Eucalyptus and Babul over 20 months, were seriously attacked. Treated samples with Celcure of Alder and Oriental plane after 38 months were completely damaged and Eucalyptus over 38 months were severely degraded. Creosote treated samples of Eucalyptus over 58 months and Babul over 38 months were seriously attacked. Creosote treated of Alder and Oriental plane samples after 64 months installation were sound. It can be concluded that treatment with Creosote using full cell process (Bethel) increased resistance of investigated wood species against marine borers.}, keywords = {MARINE BORERS,wood,Treatment,CREOSOTE,CELCURE,durability}, title_fa = {بررسی دوام چوبهای توسکا، چنار، اکالیپتوس کاملدولنسیس و کرت در مقابل حفاران دریایی در ساحل بندر بوشهر}, abstract_fa = {نمونه های آزمونی از گونه های توسکا (Alnus subcordata)، چنار (Platanus orientalis)، اکالیپتوس کاملدولنسیس (Eucalyptus camaldulensis) و کرت (Acacia arabica) به ابعاد 200×75×20 میلیمتر تهیه و به روش بتل با مواد حفاظتی کرئوزوت و سلکور 5% اشباع شدند. نمونه های اشباع شده همراه نمونه های شاهد این گونه ها در ساحل بندر بوشهر در داخل دریا، نصب شدند. دوام نمونه های آزمونی در مقابل حفاران دریایی (marine borers) پس از 9، 15، 24، 29، 38، 47، 53، 58 و 64 ماه استقرار در آب دریا، براساس آیین نامه شماره D-2481 استاندارد ASTM و دستورالعمل شماره4432 انجمن جهانی حفاظت چوب (IRG)، مورد ارزیابی قرار گرفتند. نتایج بدست آمده نشان داد که نمونه های شاهد توسکا و چنار پس از 9 ماه و اکالیپتوس کاملدولنسیس پس از 20 ماه و کرت پس از 29 ماه استقرار در دریا، به طور کامل تخریب شدند. نمونه های توسکا و چنار اشباع شده با سلکور، پس از 38 ماه استقرار در دریا، به درجه تخریب 0 (تخریب کامل) رسیدند. نمونه های توسکا و چنار اشباع شده با کرئوزوت، پس از 64 ماه به وسیله حفاران دریایی تخریب نشدند ولی آثار پوسیدگی نرم در سطوح نمونه ها به طور کامل مشهود بود. نمونه های آزمونی اکالیپتوس کاملدولنسیس اشباع شده با کرئوزوت پس از 53 ماه و همینطور کرت اشباع شده با کرئوزوت، پس از34 ماه استقرار در دریا، به طور کامل تخریب شدند. علت آن ممکن است میزان پایین جذب کرئوزوت در نمونه های اکالیپتوس کاملدولنسیس و کرت باشد.}, keywords_fa = {حفاران دریایی,چوب,اشباع,کرئوزوت,سلکور و دوام}, url = {https://ijwpr.areeo.ac.ir/article_117564.html}, eprint = {https://ijwpr.areeo.ac.ir/article_117564_3471a83dc1d00db39f43dcaf54340f39.pdf} }