@article { author = {Brazandeh, Mohammad Mehdi and Hosseinkhani, Hossein and Eshagi, Saeid and Fakhryan, Abas}, title = {Evaluation of formaldehyde emissions from composite wood products}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {28}, number = {2}, pages = {195-204}, year = {2013}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2013.2775}, abstract = {Abstract Regarding undesired effects of formaldehyde on the health of people and enviroment, it is desired to evaluate the amount of emission of this gas from a wood composite product in order to introduce a practical method for evaluating the amount of it,s emission from any other wood product. To do this, particleboards of Haloxyon persicum were prepared in three different moisture levels using urea-formaldehyde adhesive. Formaldehyde emissions were evaluated as p.p.m using desciccator method ASTM D 5582-00.The results show that formaldehyde emission is reduced by raising moisture gradient such as emission values were determined as 8.946 ppm, 6.312 ppm and 4.172 ppm for the  particleboards with moisture gradients of 0, 2 and 4 percent, respectively. Increasing moisture gradient from 0 to 2 percent resulted in 29 percent and increasing moisture gradient from 2 to 4 percent resulted in 34 percent less formaldehyde emissions, respectively. In addition, comparison these amounts with standard values show that these particleboards should be only used in the outdoors and not be used in the indoors  at any way. }, keywords = {Formaldehyde,Particleboard,wood products,desciccator method}, title_fa = {تعیین میزان انتشار فرمالدهید از فراوردههای مرکب چوبی}, abstract_fa = {چکیده با توجه به تأثیر نامطلوب گاز فرمالدهید بر سلامت انسان و محیط‌زیست، میزان انتشار این گاز از یک فراورده چوبی، تعیین گردیده تا بدین طریق روشی عملی برای اندازه‌گیری میزان انتشار این گاز از هر فراورده چوبی دیگر ارائه گردد. بدین منظورنمونه‌های تخته خرده‌چوب از چوب درخت زرد تاغ با تغییر گرادیان رطوبتی در سه سطح و با استفاده از چسب‌اوره فرمالدهید ساخته شدند. سپس با استفاده از روش دسیکاتور طبق دستور العمل شماره D 5582-00 مربوط به آیین‌نامه ASTM، میزان انتشار گاز فرمالدهید از هر نمونه بر حسب میکروگرم فرمالدهید بر میلی‌لیتر محلول (ppm)، محاسبه گردید. نتایج بدست آمده نشان می‌دهند که با افزایش گرادیان رطوبت، میزان انتشار گاز فرمالدهید، کاهش می‌یابد به طوری که میزان انتشار از تخته‌های خرده‌چوب با گرادیان رطوبتی صفر درصد، ppm 946/8، تخته‌های خرده‌چوب با گرادیان رطوبتی 2 درصد، ppm 312/6 و تخته‌های خرده‌چوب با گرادیان رطوبتی 4 درصد، ppm172/4 فرمالدهید اندازه‌گیری شد. با افزایش گرادیان رطوبت از صفر درصد به 2 درصد، انتشار فرمالدهید، به میزان 29 درصد و با افزایش گرادیان رطوبت از 2 درصد به 4 درصد، انتشار گاز فرمالدهید، به میزان 34 درصد  کاهش می‌یابد. همچنین مقایسه این مقادیر با مقادیر استاندارد و مجاز نشان می‌دهد که این تخته‌ها فقط در فضاهای باز باید مورد استفاده قرار گرفته و از به کار بردن آنها در محیط های داخلی شدیداً باید اجتناب شود.}, keywords_fa = {فرمالدهید,تخته خردهچوب,فراوردههای چوبی,روش دسیکاتور}, url = {https://ijwpr.areeo.ac.ir/article_2775.html}, eprint = {https://ijwpr.areeo.ac.ir/article_2775_b3377a4f2c1d85f49bc4d22d7aa8249b.pdf} } @article { author = {Tajdini, Azhang and Taghadosi, Amir hossein and Pourmousa, Shadman and Jahan-Latibari, Ahmad and Safdari, Vahid reza}, title = {Study of the effective indices on imports of Wooden furniture in Iran}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {28}, number = {2}, pages = {205-223}, year = {2013}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2013.2776}, abstract = {Abstract: In the recent years due to the innovations taking place in the production, packaging and shipping of furniture, world trade of these products has grown substantially. This issue along with some outstanding problems in manufacturing and marketing various kinds of wooden has caused that furniture imports to Iran has enjoyed significant growth .In order to achieve the efficient and economic import, identify all factors that the perspective of experts led to prefer these products in compared with similar domestic production will be essential, therefore in this research in order to investigate the reasons for the expansion of the import quantities, the standardized questionnaires (certified by professionals and academic professors in  four groups: Economics, Environment, Technical and Technological, and Consumption) are provided by use of documentary and survey research methods to investigate the effective indices on importing wooden furniture to Iran in order to describe the reasons of its widespread throughout Iranian experts. These main indexes indices of imports are rated by three methods: Likert spectrum, Duncan Test, and relative importance ratio of each index. We applied Likert spectrum on the whole statistical population and it shows that Environment index holds the first rank and Consumption, Technical and Technological, and Economics indexes are followed respectively. Duncan test shows Economics index has the first rank, Environment index holds the second place. Technical and Technological index are in the same place as Consumption index and according to the test there is no meaningful differences between them. On the other hand, using the relative importance ratio method we classified related occupations into 4 groups: producers, vendors/ distributers, importers, and consumers. We employed third method to see how these four groups evaluate the importance of each index. Results are as follows: PRODUCERS believe that Environment index is in the first place and then Economics, Technical and Technological, and finally Consumption index. VENDORS/DISTRIBUTORS believe Consumption, Technical and Technological, Economics, and Environment index is the sequence. IMPORTERS believe that Consumption index is in the main priority and then Technical and Technological, Economics, and Environment hold next places.}, keywords = {Index,Wooden furniture,imports,Likert spectrum,Duncan test}, title_fa = {بررسی شاخص‌های مؤثر بر واردات محصولات مبلمان چوبی به ایران}, abstract_fa = {در طی سالیان اخیر با توجه به نوآوری‌های صورت پذیرفته در تولید، بسته‌بندی و حمل ونقل انواع مبلمان چوبی، تجارت جهانی این محصولات رشد چشمگیری داشته است. این مسئله به‌همراه برخی مشکلات چشمگیر در تولید و بازاریابی، سبب گردیده واردات انواع مختلف مبلمان چوبی به ایران از رشد قابل ملاحظه‌ای در طی سالیان اخیر برخوردار باشد. جهت حصول به وارداتی مقرون به صرفه و اقتصادی، شناخت کلیه عواملی که از دیدگاه صاحب نظران موجب ترجیح این‌گونه محصولات نسبت به انواع مشابه تولیدی داخلی می‌گردد بسیار مهم و ضروری می‌باشد، بنابراین در این تحقیق با هدف آسیب‌شناسی علل گسترش حجم واردات، شاخص‌های مؤثر بر واردات با استفاده از روشهای تحقیق اسنادی و پیمایشی در قالب طراحی پرسشنامه‌هایی استاندارد با استفاده از نظرات و صاحب نظران آگاه در دانشگاه و نهادهای مرتبط در چهار گروه اصلی اقتصادی، محیطی، فنی و تکنولوژی، و مصرفی تعریف شدند برای بررسی روایی پرسشنامه از روش الفای کرون باخ و برای ارزیابی اعتبار پرسشنامه ار روش اعتبار محتوی استفاده گردید. رتبه‌بندی شاخص‌های اصلی مؤثر بر واردات به سه روش طیف لیکرت، آزمون دانکن و ضریب اهمیّت نسبی هر شاخص انجام پذیرفت. نتایج به‌دست آمده از طیف لیکرت برای کل جامعه آماری نشان داد که شاخص محیطی در واردات محصولات مبلمان در رتبه اول قرار داشته و شاخص‌های مصرفی، فنی و تکنولوژیکی، و اقتصادی به‌ترتیب در مراتب بعدی قرار گرفته است. به‌وسیله آزمون دانکن شاخص‌های کلی رتبه‌بندی مشخص شد که شاخص اقتصادی در رتبه اول قرار داشته و در رتبه دوم شاخص محیطی قرار گرفته است و شاخص (فنی و تکنولوژیکی) و (شاخص مصرفی) در جایگاه سوم قرار می‌گیرند و بین این دو شاخص تفاوت معناداری وجود ندارد. در رتبه‌بندی شاخص‌های کلی به روش اهمیّت نسبی، با تقسیم‌بندی کلی مشاغل در چهار دسته به شرح تولیدکننده، فروشنده یا توزیع کننده، واردکننده و مصرف‌کننده، با اعمال درصد اهمیّت نسبی از دیدگاه هر یک از این مشاغل به شاخص‌های اصلی، اهمیّت هر یک از شاخص‌ها را از دیدگاه مشاغل فعال در این صنف به‌دست آمد، نتایج نشان از تفاوت اهمیّت نسبی شاخص‌ها از دید هریک از این چهاردسته دارد.}, keywords_fa = {شاخص,مبلمان چوبی,واردات,طیف لیکرت,آزمون دانکن}, url = {https://ijwpr.areeo.ac.ir/article_2776.html}, eprint = {https://ijwpr.areeo.ac.ir/article_2776_1536f8ff8110aa8c2936f8077b556e89.pdf} } @article { author = {Rangavar, Hossein and Bazyar, Behzad and Akbari, Hamed}, title = {study on the possibility of particle board tree-layer manufacturing using of Cicer arietinum stem}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {28}, number = {2}, pages = {224-237}, year = {2013}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2013.2786}, abstract = {Abstract : In this study, the possibility of using Cicer arietinum straw residues for manufacturing three-layer particleboards was studied.The amounts of Cicer arietinum straw in mixture with industrial particles were ( % 25:75),(% 40:60),(% 55:45) respectively.Urea formaldehyde (100%) and Melamin urea formaldehyde at different ratios of MF / UF were  used as binders. The resin were applied at two levls of (% 8,10) in core and two levels of (% 10,12) in surface layers, based on oven dried weight of particles. Mechanical and physical properties of boards ( Modulus of rupture, Modulus of elasticity, Internal bonding and thickness swelling and water absorption after 2, 24 hours soaking in water) were measured and data were analyzed, statistically. The results indicated that increase of Cicer arietinum straw lead to increase of bending strength and Modulus of elasticity. Also  the increase of resin content and use of Melamin urea formaldehyde resin caused to improve mechanical and physical properties. In General, the use of Cicer arietinumstraw in mixture with industrial particles up to 55% , and resin content of (10,12%) in core and surface layers, resulted in producing boards with appropriate mechanicals properties which are suitable for interior uses. }, keywords = {Particleboard,Cicer arietinum straw,Melamin urea formaldehyde,Modulus of rupture,Modulus of elasticity}, title_fa = {بررسی امکان ساخت تخته خرده‌چوب سه لایه با استفاده از ساقه نخود زراعی}, abstract_fa = {چکیده در این مطالعه امکان استفاده از پسماند ساقه نخود، در ساخت تخته خرده‌چوب سه لایه به‌صورت خالص در لایه رویی با خرده‌چوب صنعتی در لایه مرکزی مورد بررسی قرار گرفت. درصد اختلاط ساقه نخود با خرده‌چوب صنعتی به‌ترتیب در سه سطح (25 درصد ساقه نخود: 75 درصد خرده‌چوب)، (40 درصد ساقه نخود: 60 درصد خرده‌چوب) و (55 درصد ساقه نخود: 45 درصد خرده‌چوب)، نوع چسب شامل اوره‌فرمالدهید (100 درصد)، ملامین اوره‌فرمالدهید با مقدار‌های متفاوت (80 درصدUF  و 20 درصد MF) و (70 درصدUF  و 30 درصد MF) و همچنین مقدار چسب مصرفی در دو سطح (8 و10) درصد در لایه مرکزی و (10 و 12 درصد) در لایه رویی به‌‌عنوان عوامل متغییر انتخاب گردیدند. خواص مکانیکی شامل مدول‌گسیختگی، مدول‌الاستیسیته و چسبندگی‌داخلی و همچنین خواص فیزیکی، واکشیدگی ضخامت و جذب آب در طی 2 و 24 ساعت غوطه‌وری در آب نمونه‌ها، طبق استاندارد EN اندازه‌گیری گردید. نتایج نشان داد که استفاده از ساقه نخود در لایه‌های سطحی تخته خرده‌چوب سه لایه، سبب افزایش مقاومت‌خمشی و مدول‌الاستیسیته و کاهش چسبندگی‌داخلی و افزایش واکشیدگی ضخامت و جذب آب نمونه‌ها گردید. نتایج همچنین نشان داده است که افزایش مقدار چسب و استفاده از چسب ملامین اوره‌فرمالدهید با مقدار بیشتر ملامین باعث بهبود خواص مکانیکی و فیزیکی نمونه‌ها شده است. به طور کلی می‌توان گفت که با استفاده از 55 درصد ساقه نخود در لایه‌رویی و مقدار چسب 12 درصد در لایه‌های سطحی و 10 درصد در لایه‌های میانی با ترکیب (30 درصد ملامین و 70 درصد اوره‌فرمالدهید) می‌توان تخته‌هایی با خواص مکانیکی بالاتر از حد استاندارد (EN) تولید نمود. همچنین استفاده از مواد ضد رطوبت برای بهبود خواص فیزیکی تخته‌ها لازم می‌باشد.    }, keywords_fa = {تخته خرده‌چوب سه لایه,ساقه نخود,ملامین اوره‌فرمالدهید,مدول‌گسیختگی,چسبندگی‌داخلی,واکشیدگی ضخامت}, url = {https://ijwpr.areeo.ac.ir/article_2786.html}, eprint = {https://ijwpr.areeo.ac.ir/article_2786_67122086505c2ac38e73ec046bc6fbe6.pdf} } @article { author = {Kohantorabi, Mostafa and Rohnia, Mehran}, title = {Detection of defects in joints using the variations in dynamic shear modulus and Correlation Coefficient factor in Beech Wood}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {28}, number = {2}, pages = {238-257}, year = {2013}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2013.2789}, abstract = { In this study, detect of damage in scarf joint and finger joint using the variations in dynamic shear modulus values and Correlation Coefficient factor of the beech wood specimens was investigated. Numbers of 42 Samples were selected according to ISO 3129 international standard. The Scarf and finger joints created with three different glue coverage rates in samples and then flexural vibration tests in free-free beam were performed. The results showed that defects changed the dynamic shear modulus values in both joints, however it is not possible to realize the amount of defects from these variations. Whereas, the changes in Correlation Coefficient factor were useful to detect the amount of defects in both joints.  }, keywords = {flexural vibration,Scarf joint,Finger joint,Dynamic shear modulus,Correlation Coefficient factor}, title_fa = {تشخیص معایب در اتصالات از طریق تغییرات حاصل در ضریب همبستگی و مدول برشی‌ دینامیک در چوب راش}, abstract_fa = {چکیده در این تحقیق به بررسی امکان ردیابی نقص در اتصالات‌فارسی و انگشتی از طریق تغییرات حاصل در ضریب‌همبستگی و مدول‌برشی دینامیک پرداخته شده است. تعداد 42 نمونه سالم و بدون عیب ظاهری مطابق با استاندارد بین‌المللی ISO شماره 3129 انتخاب و پس از ایجاد دو اتصال فارسی و انگشتی در سه سطح چسب‌گذاری شده و تحت آزمون ارتعاش آزاد خمشی در تیر دوسر آزاد قرار گرفتند. نتایج نشان داد که وجود نقص در هر دو اتصال سبب تغییر در مدول‌برشی دینامیک می‌گردد اما از روی تغییرات ایجاد شده بر روی این فاکتور نمی‌توان به میزان نقص پی‌برد. در صورتی که از طریق تغییرات ایجاد شده در ضریب‌همبستگی علاوه بر وجود نقص در دو اتصال مورد تحقیق، می‌توان میزان نقص را نیز پیش‌بینی نمود.}, keywords_fa = {ارتعاش‌خمشی,اتصال‌فارسی,اتصال‌انگشتی,مدول‌برشی‌دینامیک,ضریب‌همبستگی}, url = {https://ijwpr.areeo.ac.ir/article_2789.html}, eprint = {https://ijwpr.areeo.ac.ir/article_2789_2fde7611f771f056b70563eafe8b080a.pdf} } @article { author = {Haghighi, Azar and Taghiyari, Hamid reza and Karimi, Ali nagi}, title = {Study on Fire-Retarding Properties of Nano-Wollastonite in Fir Wood (Abies alba)}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {28}, number = {2}, pages = {252-265}, year = {2013}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2013.2791}, abstract = {In the present study, fire-retardant properties of nano-wollastonite in fir wood (Abies alba) was studied. Water absorption and volume swelling of the specimens were also measured. Specimens were prepared according to ISO 11925 standard specifications to measure the fire-retarding properties, and ASTM D4446 -2002 standard to measure physical properties. Impregnation of wood specimens with nano-wollastonite was carried out at four consumption levels of 4, 6/3, 10 and 12%, using Bethel method (full-cell process).Five fire-retarding properties were measured; weight loss (%), ignition point (s), duration of flame after removing the burner (s), duration of glow after removing the burner (s),and carbonization area (%). The results showed that fire-retarding properties increased with the NW-content. Furthermore, the treated wood specimens showed higher dimensional stability. }, keywords = {Bethel method,Fir Wood,Fire-Retarding Properties,IMPREGNATION,nano-wollastonite,Volume swelling,water absorption}, title_fa = {بررسی اثر کندسوزکنندگی نانوولاستونیت در چوب نرّاد (Abies alba)}, abstract_fa = {در این مطالعه قابلیت کندسوزکنندگی نانو­ولاستونیت در چوب نراد (Abies alba) مورد بررسی قرار گرفت. همچنین میزان جذب آب و واکشیدگی حجمی نمونه­ها نیز اندازه­گیری شد. نمونه­های آزمونی طبق استاندارد 11925ISO  مربوط به اندازه­گیری خواص مقاومت به آتش و استانــــدارد 2002- 4446 ASTM-D مربوط به اندازه­گیری خواص فیزیکی تهیه شدند. اشباع نمونه‌های چوبی با نانو­ولاستونیت با استفاده از روش بتل در چهار سطح غلظت 4، 3/6، 10 و 12 درصد انجام شد. ویژگی مقاومت به آتش نمونه­های مورد مطالعه توسط پنج معیار (درصد کاهش وزن، نقطه اشتعال، دوام شعله، دوام گدازش و درصد سطح کربونیزه شده) مورد بررسی قرار گرفت. نتایج نشان داد که با افزایش غلظت نانوولاستونیت مقاومت به آتش نمونه­های تیمار شده افزایش یافت. همچنین، چوب تیمار شده با این ماده افزایش ثبات ابعاد بیشتری نیز نشان داد. با توجه به آزمون خوشه‌ای بر مبنای تمامی خواص اندازه‌گیری‌شده، مقدار مصرف 10 درصد پیشنهاد می‌شود. }, keywords_fa = {روش بتل (سلول تهی),چوب نراد,ویژگی¬های کندسوزکنندگی,اشباع,نانو¬ولاستونیت,واکشیدگی حجمی,جذب آب}, url = {https://ijwpr.areeo.ac.ir/article_2791.html}, eprint = {https://ijwpr.areeo.ac.ir/article_2791_c37f62ad44134d915f12b259bd797869.pdf} } @article { author = {Sepahvand, ُSima and Ziaee Khosro Shahi, Saeid and Tabarsa, Tagi}, title = {The manufacture of particleboard using tannin-modified urea formaldehyde adhesive}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {28}, number = {2}, pages = {266-276}, year = {2013}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2013.2792}, abstract = {This study provides an investigation of particleboard manufacture using tannin-ureaformaldehyde adhesive. Test board samples were made with regard to various replacementpercentage of tannin–urea (levels of 0, 10, 20 and 30%) and press time (12 and 15 min) andtheir properties were determined. Achieved data were analyzed according to two sides factorialplan. The results showed that with replacement of 10% urea formaldehyde adhesive by tanninformaldehydeat both 12 and 15 min pressing times, thickness swelling (after 2 and 24 hoursimmersion in water) was decreased while internal bonding increased. There were no significanteffect on MOR and MOE values. In general, the results of present research showed thatreplacing the UF resin at lower levels of tannin is suitable as adhesive to manufactureparticleboard so that with replacement ratio of 90:10, the moisture properties of boards werevery close to permissible those of the exterior wood uses.}, keywords = {Particleboard,tannin - urea formaldehyde adhesive,press time,modulus of rupture,Internal bonding}, title_fa = {تولید تخته خرد هچوب با استفاده از چسب اوره فرمالدهید اصلاح شده با تانن فرمالدهید}, abstract_fa = {در این تحقیق با استفاده از مخلوط تانن فرمالدهید و چسب اوره فرمالدهید تخته خرده چوب ساخته شده و ویژگی های آنمورد بررسی قرارگرفت . تختههای آزمایشی با توجه به عوامل متغیر شامل درصد جایگزینی تانن فرمالدهید در اوره فرمالدهید(سطوح صفر، 20،10 و 30 درصد ) و زمان پرس ( 12 و 15 دقیقه) ساخته شد ه و خواص آ نها اندازه گیری شد . داده ها ی به دستآمده در قالب طرح فاکتوریل دو عامله مو رد تجزیه و تحلیل قرار گرفت . نتایج نشان داد که جایگزین ک ردن ده درصد رزیناوره فرمالدهید با تانن در هر دو زمان پرس 12 و 15 دقیقه، مقدار واکشیدگی ضخامتی پس از 2 و 24 ساعت غوطه وری در آباثر معنی داری نشان (MOE) و مدو لالاستیسیته (MOR) کاهش و چسبندگی داخلی افزایش یافت. این تغییر بر م دول گسیختگیبه عنوان چسب ساخت تخته خرده چوب UF نداد. به طورکلی نتایج این بررسی نشان داد که جایگزینی در مقادیر کم تانن رزینمناسب می باشد. به طوری که خواص رطوبتی تخته های ساخته شده با نسبت جایگزینی 90:10 بسیار نزدیک به مقادیر مجاز اینخواص برای مصارف بیرونی تخته خرده چوب بود.}, keywords_fa = {تخته خرده چوب,چسب تانن- اوره فرمالدهید,زمان پرس,مدول گسیختگی,چسبندگی داخلی}, url = {https://ijwpr.areeo.ac.ir/article_2792.html}, eprint = {https://ijwpr.areeo.ac.ir/article_2792_a7072a2bf6c45f625e4a70a7294053b5.pdf} } @article { author = {Yahyavidizaj, Mostafa and khozini, Asieh and Tabarsa, Tagi}, title = {The manufacture of particleboard using mixture of golestan province wheat straw and cotton bolls reinforced with nano-clay particles}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {28}, number = {2}, pages = {277-289}, year = {2013}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2013.2933}, abstract = {In this study, Wheat straw particle boards were produced using a mixture of wheat straw andcotton bolls with Urea formaldehyde resin and its properties were reinforced with nanoclay.Cotton bolls and wheat straw particles were mixed at the ratio of 40:60, 60:40 and 80:20percents, respectively. Nanoclay was used at two levels of 0 and 2 percents based on oven driedweight of resin. Control samples were made of Wheat straw particle. Mechanical and physicalproperties (modulus of rupture, modulus of elasticity, internal bonding, water absorption andthickness swelling after 2 and 24h soaking in water) of the produced boards were measured.The results revealed an increase in cotton bolls in the mixture particles, leads to an increase ofthe bending strength, modulus of rupture and modulus of elasticity of the boards. The resultsalso indicated that water absorption and thickness swelling after 2 and 24h immersion in waterdecreased with increase in nano clay and cotton bolls percents.}, keywords = {Golestan Province,WHEAT STRAW,cotton bolls,wheat straw particle boards,Nanoclay}, title_fa = {بررسی امکان استفاده از کا ه گندم و قوز ه پنبه استان گلستان در ساخت تخته خرد ه کاه و تقویت آن با نانورس}, abstract_fa = {در این پژوهش با استفاده از اختلاط کا ه گندم و قوز هپنبه، تخته خرد ه کاه با چسب اور ه فرمالدهید تولید و خواص آن با60 و 80 درصد نانورس 0 و 2 درصد براساس ، نانورس تقویت شد . درصد اختلاط قوزه پنبه با کا ه گندم در سه سطح ب ه ترتیب 40وزن خشک چسب به عنوان عوامل متغیر انتخاب گردید . نمونههای شاهد نیز از 100 درصد کاه گندم ساخته شدند . خو اصفیزیکی و مکانیکی تخته ها شامل: مقاومت خمشی، مدول الاستیسیته، چسبندگی داخلی، جذب آب و واکشیدگی ضخامت در طیاندازه گیری شد. نتایج نشان داد که استفاده از قوز هپنبه و نانورس DIN- 2 و 24 ساعت غوطه وری در آب، برطبق استاندارد 68763تخته ها (IB) و چسبندگی داخلی (MOE) مدول الاستیسیته ،(MOR) در ساخت تخته خرده کاه ، باعث افزایش مقاومت خمشیمیشود. همچنین نتایج نشان داد، با افزایش درصد قوز هپنبه و نانورس جذب آب و واکشیدگی ضخامت بهبود یافت.}, keywords_fa = {استان گلستان,کاه گندم,قوزه پنبه,تخته خرد هکاه,نانورس}, url = {https://ijwpr.areeo.ac.ir/article_2933.html}, eprint = {https://ijwpr.areeo.ac.ir/article_2933_6c1ecdf1a5f2d317bc6358f9a712b1f8.pdf} } @article { author = {Shakeri, َAbdolah and Safdari, Vahid Reza and Rohnia, Mehran and Nourbakhsh, Amir}, title = {An analysis of the combined effects of isocyanate HMDI and maleic anhydride (MAPE) coupling agents on the mechanical properties of HDPE- wood flour composite}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {28}, number = {2}, pages = {290-300}, year = {2013}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2013.2934}, abstract = {Coupling agents in wood fiber reinforced plastic composites play an important role inimproving compatibility and adhesion between polar wood fiber and non-polar polymermatrices by forming bridges of chemical bonds between the fiber and the matrix. Maleatedpolyethylene (MAPE) and diisocyanate (HMDI) are two most common coupling agents whichare subject to evaluation, singly and in mixture. Polypropylene and wood fibers werecompounded with Maleated polyethylene (MAPE) and diisocyanate (HMDI) in concentration of2% and 4% in solitary form and mixture form (HMDI %2 + MAPE %2) into pellets using acounter-rotating twin-screw extruder and mechanical test specimens were prepared by injectionmolding. The result showed that adding 4% MAPE and 2% HMDI individually lead to increasein flexural and tensile strength of the composites. Also adding (%2HMDI + %2MAPE) causedan increase of flexural, tensile and in particular the impact strength.}, keywords = {Wood Plastic Composite,Coupling agent,Isocyanate,Extruder,mechanical test}, title_fa = {بررسی اثر همزمان جفت کننده های ایزو سیانات (HMDI) و مالئیک انیدرید (MAPE) بر روی خواص مکانیکی چندسازه آرد چوب-پلی اتیلن سنگین}, abstract_fa = {جفت کننده ها در فرآورده های چند سازه چوب پلاستیک نقش مهمی را در بهبود اتصال بین فیبرهای چوبی قطبی و ماده زمین ةپلاستیک غیر قطبی بازی می کنند. افزودن مقدار مطلوب جفت کننده ها به مخلوط چوب پلاستیک باعث می شود تا مقاومتجزء رایج ترین (HMDI) و ایزوسیانات (MAPE) مکانیکی چنین فرآورده ای به میزان قاب لتوجهی افزایش یابد. مالئیک انیدریدجفت کننده های فرآورده های چند سازه چوب پلاستیک هستند که این پژوهش به بررسی مقدار بهینه هر یک از این جفت کننده ها،به صورت انفرادی و ترکیبی پرداخته است . به همین منظور آرد چوب و پلی اتیلن سنگین با هر یک از جفت کننده ها ،+ %1 MAPE) به تنهایی در مقادیر 2 و 4 درصد و به ص ورت ترکیبی (HMDI) و ایزوسیانات (MAPE) مالئیک انیدرید%2 ) در دستگاه روزن ران دوماردونه ناهمسوگرد اختلاط یافته و توسط دستگاه قالب گیری MAPE + %2 HMDI) %1 ) و HMDIبه MAPE تزریقی، نمونه های آزمون مکانیکی ساخته شدند. نتایج حاصل از آزمون های مکانیکی نشان داد که افزودن جفت کنندةبه مقدار 2 درصد، سبب افزایش خواص کششی و خمشی فرآورد ه های چو ب پلاستیک HMDI مقدار 4 درصد و جفت کنندةبه صورت ترکیبی سبب بهبود خواص MAPE و HMDI گردید. همچنین نمونه های ساخته شده با 2 درصد از جف تکننده هایکششی و خمشی و ب هویژه مقاومت به ضربه شد.}, keywords_fa = {چندسازه چوب پلاستیک,جفت کننده,ایزوسیانات,روزن ران,آزمون مکانیکی}, url = {https://ijwpr.areeo.ac.ir/article_2934.html}, eprint = {https://ijwpr.areeo.ac.ir/article_2934_aaaaa785a2d3c31ad29d6f1091e61ec8.pdf} } @article { author = {Aghakhani, Mohammad and khazaeyan, Abolgasem and Madhoshi, Mehrab}, title = {Different CNC machining condition of paulownia wood by CNC; Influence on the abbott roughness parameters}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {28}, number = {2}, pages = {301-312}, year = {2013}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2013.2935}, abstract = {The aim of this study was to investigate the factors affecting surface quality of paulowniawood during milling by advanced computer numerical control (CNC) machine. For this aimwood logs were provided and were converted to proper sizes (2.5 x 10 x 15 cm) and then airdried. The Variable of this study were spindle speed of machine (10000 and 18000 rpm),feeding rate (6 and 12 m/min), cutting depth (1and 5 mm), cutting method (down and upmilling)and cutting pattern (tangential and radial). Roughness of cut specimens edge wereevaluated by profilometer method according to ISO 13565 standard. For evaluation of surfacequality Abbott group parameters (Rpk, Rk, Rvk) were used. Degree of effective of theparameters was evaluated by fractional factorial design as completely random design atconfidence level of 95%. The result showed that spindle speed, cutting method and feed rate areinfluencing factors on surface quality of milled specimens and their effect was significant. Withincreasing spindle speed and decreasing feeding rate the roughness decreased and surfacequality improved. In up-milling cutting method, degree of roughness was higher andconsequently surface quality was inferior. It is to be noted that cutting method in comparison toother factors had the high influence on surface quality. The rest variable did now haveindependent influence on surface quality at 95% Confidence level.}, keywords = {Milling,Cutting speed,Feeding rate,Profilometery,Surface roughness}, title_fa = {شرایط مختلف ماشی نکاری چوب پالونیا با CNC: تاثیر بر عوامل زبری گروه آبوت}, abstract_fa = {در این پژوهش عوامل اثرگذار بر زبری سطح چوب پالونیا طی فرایند فرزکاریگرده بینه های پالونیا با استفاده از اره نواری برش داده شده و الوارها در فضای سرپوشیده و در جریان هوای آزاد خشکآماده CNC 2/5 سانتی متر تهیه و برای برش کاری با دستگاه ×10× شدند. از الوارهای خشک شده نمونه هایی به ابعاد 15برش داده شدند. سرعت چرخشی محور در ASTM D- براساس استاندارد شماره 166687 CNC گردید. نمونه ها در دستگاهدو سطح 10000 و 18000 دور در دقیقه ، سرعت تغذیه در دو س طح 6 و 12 متر در دقیقه، عمق برش در دو سطح 1 و 5میلیمتر، روش کار به دو صورت همراه و مقابل و الگوی برش به دو صورت در جهت مماسی و شعاعی به عنوان عواملمتغیر انتخاب گردیدند . ناهمواری سطح نمونه های برش خورده با ب ه کارگیری روش پروفیلومتری و براساس استاندارداستفاده شد . (Rvk و Rpk, Rk,) مورد ارزیابی قرار گرفت. به منظور ارزیابی زبری سطح از عوامل گروه آبوت ISO 13565میزان تأثیر عوامل مورد مطالعه، تحت آزمون فاکتوریل شکسته، در قالب طرح کاملا تصادفی در سطح اطمینان % 95 موردبررسی قرار گ رفت. نتایج نشان داد که سرعت چرخشی محور ، روش کار و سرعت تغذیه اثر معنی داری بر عوامل زبریگروه آبوت داشت. بدین صورت که با افزایش سرعت چرخشی محور و کاهش سرعت تغذیه مقادیر عوامل زبری کاهشیافت و منجر به افزایش کیفیت سطح گردید . روش کار مقابل باعث افزایش مقادیر عوامل زبری و نهایتا افزایش زبریسطح نمونه ها شد.}, keywords_fa = {فرزکاری,سرعت چرخشی محور,سرعت تغذیه,پروفیلومتری,زبری سطح}, url = {https://ijwpr.areeo.ac.ir/article_2935.html}, eprint = {https://ijwpr.areeo.ac.ir/article_2935_375b24a7909d519fb2d6088c40ae07e8.pdf} } @article { author = {Pesaraklu, Ali and Dehghani firoz abadi, Mohammadreza and Karegarfard, Abolfazl and Tabarsa, Taghi}, title = {The effects of thermal treatment and resin type on physical and mechanical properties of Kenaf stalk particleboard}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {28}, number = {2}, pages = {313-328}, year = {2013}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2013.2936}, abstract = {The objective of this study was to manufacture water resistant kenaf stalk particleboard.Twenty seven boards were produced using 170 °C steam treated kenaf particles, 30 and 60minute treatment time and three resin types include urea-formaldehyde, melamineformaldehydeand a mixture of fifty percent each. Physical and mechanical properties weremeasured and the results analyzed in a complete random design plan and by the factorialanalysis. The results showed that boards made from treated particles with 60 minute treatmenttime and Urea Formaldehyde resin had the highest bending strength. Modulus of elasticity(MOE) improved with an increase in treatment time. The greatest MOE was achieved with theboards produced using urea-formaldehyde and the greatest MOE was achieved with the boardsbonded with urea-melamine-formaldehyde resin. Moreover, with increasing treatment time from30 to 60 minutes internal bond strength (IB) reduced. Thickness swelling and water absorptionof the boards was significantly improved with increasing treatment time.}, keywords = {Thermal treatment,kenaf,water absorption,Thickness swelling,UF,MUF}, title_fa = {اثر تیمار حرارتی خرده های مغز ساقه کنف بر ویژگی های فیزیکی و مکانیکی تخته های ساخته شده از آن}, abstract_fa = {این پژوهش با هدف ساخت تخته های مقاوم به رطوبت از خرده های تیمار حرارتی شده مغز ساقه کنف انجامگردید. با استفاده از خردههای تیمار شده مغز کنف با بخار در دمای 170 درجه سانتیگراد، با 2 زمان 30 و 60دقیقه و 3 نوع رزین اور هفرمالدئید، ملامی نفرمالدئید و مخلوط آنها به نسبت 50 درصد از هر رزین 27 تختهآزمایشگاهی ساخته شد. ویژگیهای فیزیکی و مکانیکی اندازهگیری و نتایج بهدست آمده در قالب طرح کاملاًتصادفی و با استفاده از آزمون فاکتوریل مورد تجزیه و تحلیل قرار گرفت . نتا یج نشان داد که تخته های ساخته شدهاز خردههای تیمار شده با زمان 60 دقیقه و رزین اوره فرمالدئید دارای بیشترین مقاوم تخمشی بودند. همچنین باافزایش زمان تیمار مدو لالاستیسیته تختههای ساخته شده بهبود یافته و در تختههای ساخته شده از رزین اور هملامین فرمالدئید به حداکثر رسید. بهعلاوه اینکه با افزایش زمان تیمار از 30 به 60 دقیقه چسبندگ یداخلی تختهکاهش یافت. واکشیدگی ضخامت و جذب آب تخته ها نیز با افزایش زمان تیمار در حد معنی داری نسبت بهنمونههای تیمار نشده بهبود پیداکرد.}, keywords_fa = {تیمار حرارتی,کنف,جذب آب,واکشیدگی ضخامت.MUF و UF}, url = {https://ijwpr.areeo.ac.ir/article_2936.html}, eprint = {https://ijwpr.areeo.ac.ir/article_2936_4fb63dbb14eaa7703ac40b7952954202.pdf} } @article { author = {Moradyan Gilan, kezhal and Azad fallah, Mohammad and Shayghani akmal, Amir abbas and Abdolkhani, Ali}, title = {Dielectric properties of oil impregnated kraft and soda pulps}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {28}, number = {2}, pages = {329-340}, year = {2013}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2013.2937}, abstract = {This research was carried out with the aim of determining dielectric properties of bagasse unbleached soda pulp, long fiber kraft pulp and a mixture of both (20% kraft + 80% bagasse soda).The hand-sheets with 60 g/m2 basis weight were made after adjusting the freeness of pulps at levels of 200 ± 25 ml and 400± 25 ml and dried under mild condition around zero moisture content.  Then the impregnation processes were carried out with mineral oil under vacuum at certain temperature. Finally the dielectric properties of impregnated papers including capacitance, insulation resistance, dielectric constant, and loss tangent were measured. The results showed that the refining give rise to enhance the dielectric properties in particular capacitance value. The dielectric properties of oil impregnated paper also increased. According to the preliminary results, unbleached soda bagasse pulp and its mixture with kraft pulp (20% Kraft -80% bagasse soda) found to be the suitable alternative with respect of dielectric applications for replacing kraft pulp, providing successful performance of the aging test.  }, keywords = {dielectric properties,Bagasse,KRAFT,mineral oil,freeness}, title_fa = {خواص دی الکتریک خمیرکاغذهای سودا و کرافت آغشته به روغن}, abstract_fa = {این تحقیق با هدف بررسی ویژگی­های دی­الکتریک خمیرکاغذهای رنگبری نشده سودای باگاس و کرافت الیاف بلند و مخلوطی از این دو خمیرکاغذ انجام شد. برای این منظور بعد از تنظیم درجه‌روانی خمیرکاغذها در دو سطحml 25±400 و ml 25±200، کاغذهای دست­ساز با وزن پایه 60 g/m2 ساخته و تا رسیدن به رطوبت حدود صفر خشک شدند. فرایند آغشته­سازی با روغن معدنی تحت خلأ و در دمای معین انجام شد. سپس خواص دی‌الکتریک کاغذهای آغشته به روغن شامل ظرفیت، مقاومت عایق، ثابت دی­الکتریک و تانژانت تلفات اندازه­گیری شدند. نتایج نشان داد که پالایش اثر افزایشی بر خواص دی­الکتریک به خصوص ظرفیت­ دارد. از طرفی آغشته­سازی با روغن معدنی هم سبب افزایش خواص دی­الکتریک کاغذها گردید. طبق نتایج اولیه به‌دست آمده خمیرکاغذهای باگاس و همین ‌طور مخلوط آن با خمیرکاغذ کرافت (کرافت 20% و سودای باگاس 80%) را مشروط بر گذراندن موفقیت­آمیز آزمون­های پیری می­توان به‌عنوان جایگزین مناسبی برای خمیرکاغذ کرافت جهت ساخت کاغذ دی‌الکتریک به‌کار برد.}, keywords_fa = {خواص دی الکتریک,باگاس,کرافت,روغن معدنی,درجه‌روانی}, url = {https://ijwpr.areeo.ac.ir/article_2937.html}, eprint = {https://ijwpr.areeo.ac.ir/article_2937_ee5af4ab7e4b50e6e02df8df4d08afc2.pdf} } @article { author = {Mehrabi, Saeid}, title = {The use of X-ray method to study annual growth variation of Pinus eldarica}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {28}, number = {2}, pages = {341-353}, year = {2013}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2013.2949}, abstract = {Using non-destructive methods to study forest productivity and wood quality as well as annual growth variations deserve special importance. In this regard annual growth changes of Pinus eldarica include width of the spring and summer rings and percentage of tissue structure was determined using X-ray method. Spring wood accounts as the effective factor for growth ring width in pine wood. The annual rings of the tree are thicker in the spring than in the summer time. Pine tree growth rate decreases with age and as the tree age rises, width of the ring as well as   spring and summer wood width is lowered. }, keywords = {Wood radiography,non-destructive evaluation of Pinus eldarica}, title_fa = {استفاده از پرتوهای X برای مطالعه تغییرات رویش سالیانه کاج تهران}, abstract_fa = {استفاده از روش‌های غیرمخرب برای مطالعه جنگل و کیفیت چوب آن و بررسی تغییرات رویش سالیانه درخت از اهمیّت خاصی برخوردار می‌باشد. با توجه به این موضوع تغییرات رویش سالیانه کاج تهران مورد مطالعه، و با استفاده از پرتوهای X، پهنی دوایر، چوب‌بهاره، چوب‌تابستانه و درصد بافت آنها مشخص گردید. عامل مؤثر در تغییر پهنای‌دایره رویش در چوب کاج، چوب‌بهاره می‌باشد. به‌طوری‌که افزایش آن سبب افزایش پهنی دایره سالانه می‌گردد و اگر در ابتدای فصل شرایط مساعدی وجود داشته باشد می‌توان چنین تصور نمود که رویش چوب‌بهاره زیادتر شده و شتاب زیادی به پهن‌تر شدن دایره سالیانه می‌دهد. میزان رشد چوب‌بهاره بیشتر از چوب‌تابستانه می‌باشد. هر چه سن درخت کاج تهران افزایش پیدا می‌کند، میزان پهنی دایره و پهنی چوب‌بهاره و پهنی چوب‌تابستانه کمتر می‌گردد. }, keywords_fa = {رادیوگرافی چوب,آزمایش غیرمخرب چوب,کاج تهران,پهنی دوایر سالیانه}, url = {https://ijwpr.areeo.ac.ir/article_2949.html}, eprint = {https://ijwpr.areeo.ac.ir/article_2949_e2a13759e55265e0787764915dd0a94f.pdf} } @article { author = {Nikbin, Negin and Mahdavi, Saeid and Kermanian, Hossein and Ramezani, Omid and Nazeri, Amir Mohssen}, title = {Improvement of starch adhesive properties used in the carton industry}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {28}, number = {2}, pages = {354-363}, year = {2013}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2013.2950}, abstract = {Native starch has relatively suitable characteristics including biodegradable properties, being widely used as an adhesive in the corrugated carton manufacturing companies. Corn starch is currently used in the companies for producing adhesives. In this study, fines of NSSC pulp as natural additive and ammonium persulfate as chemical oxidative additive were used to improve the adhesion properties of corn starch. Fine was added at three levels of 5%, 10%, and 15% (based on oven-dry weight of starch) and ammonium persulfate similarly was mixed at 5 levels of 0.1, 0.2, 0.3, 0.4 and 0.5 grams. Addition of fine was lead to increasing adhesion strength (PAT) of the corrugating board to the amount of 25%, 35% and 43% respectively. This improvement could be due to increasing the number and strength of hydrogen bonding of fiber layers (corrugating and liner paper) and value of solid content. Addition of ammonium persulfate revealed that the method applied similar to mixing fine had no desirable results and the other methods should be used.}, keywords = {Corrugating board,starch adhesive,fine,ammonium per sulfate,Adhesion strength}, title_fa = {بهبود ویژگی های چسب نشاسته مورد استفاده در صنایع کارتن سازی}, abstract_fa = {نشاسته خام با ویژگی‌های نسبتاً مناسب ازجمله زیست‌تخریب‌پذیر بودن، کاربرد گسترده‌ای در صنایع کارتن‌سازی به‌عنوان چسب دارد. امروزه در این کارخانه‌ها عمدتاً از نشاسته ذرت برای تولید چسب استفاده می‌شود. در این تحقیق به‌منظور بهبود ویژگی‌های چسب نشاسته ذرت، از نرمه­های خمیرکاغذ سولفیت نیمه‌شیمیایی خنثی (NSSC) به‌عنوان یک افزودنی طبیعی و از پِرسولفات‌آمونیوم به‌عنوان یک افزودنی شیمیایی اکسیدکننده استفاده شد. نرمه­ها در سه سطح 5، 10 و 15 درصد و پِرسولفات‌آمونیوم در 5 سطح 1/0، 2/0، 3/0، 4/0 و 5/0 گرم بر مبنای وزن خشک نشاسته به چسب آماده افزوده شد. افزودن نرمه در 3 سطح مذکور باعث افزایش مقاومت چسبندگی (PAT) ورق‌کارتن به‌ترتیب به میزان 25%، 35% و 43% گردید. این افزایش می‌تواند ناشی از افزایش تعداد و قدرت اتصال هیدروژنی بین لیفی لایه‌ها (کاغذ کنگره‌ای و لاینر) و افزایش مقدار مواد جامد چسب باشد. نتایج افزودن پِرسولفات‌آمونیوم نشان داد که استفاده از این ماده با روش مشابه اختلاط نرمه‌ها با چسب نشاسته، نتایج مطلوبی دربر ندارد و از سایر روش‌ها باید استفاده نمود.}, keywords_fa = {مقوای کنگرهای,چسب نشاسته,نرمه,پِرسولفاتآمونیوم,مقاومت چسبندگی}, url = {https://ijwpr.areeo.ac.ir/article_2950.html}, eprint = {https://ijwpr.areeo.ac.ir/article_2950_073542599a3d2b146301195d7fd134ea.pdf} } @article { author = {Zhand, Soodeh and Masoudifar, Masieh and Saraeian, Ahmad Reza and Ghasemiyan, Ali}, title = {Effect of alkaline pre-treatment on physical, optical and mechanical properties of semi-chemical NSSC wheat straw pulp}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {28}, number = {2}, pages = {366-380}, year = {2013}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2013.2952}, abstract = {In this study the effect of alkaline pretreatment with 1% NaOH on physical, optical and mechanical properties and refining of NSSC (Neutral Sulfite Semi Chemical) wheat straw pulp were investigated. The wheat straw (Zagros Sp.) was obtained from croplands Golestan province. Splinted wheat straw was pretreated with 1% NaOH(on the basis of OD weight) at 70 degrees for 30 minutes. The main pulping was performed at 160 ˚C with the fixed ratio of 5:1 Na2S03 and NaOH. After pulping defibration was done by lab-refiner to 380±25ml (CSF) and total yield and changes in Kappa was determined. Hand sheets of 60 gr. /m² were made on the basis of TAPPI standard and physical, optical and mechanical properties determined.  The results show that alkaline pre-treatment has a significant effect in increasing of physical, optical and mechanical properties. Calculating primary freeness of pulps indicates that by increasing chemical compounds and NaOH, freeness decreases and that by increasing chemical compounds paper density increases, whereas yield, caliper and bulk decrease. }, keywords = {WHEAT STRAW,Neutral Sulfite Semi Chemical pulp,freeness}, title_fa = {تأثیر پیش تیمار قلیایی بر بازده و ویژگی های خمیر کاغذ نیمه شیمیاییNSSC کاه گندم}, abstract_fa = {در این تحقیق اثر پیش‌تیمار قلیایی با یک درصد هیدروکسیدسدیم بر ویژگی‌های فیزیکی، نوری و مقاومتی خمیر کاغذ NSSC از کاه‌گندم بررسی شد. از نمونة کاه‌گندم (رقم زاگرس) مزارع استان گلستان استفاده گردید. کاه خرد شده در دمای 70 درجه سانتی‌گراد به مدت 30 دقیقه تحت تأثیر پیش‌تیمار با یک درصد هیدروکسیدسدیم بر مبنای وزن خشک قرار گرفت. پخت‌ها در دمای 160 درجه سانتی‌گراد با نسبت ثابت سولفیت‌سدیم به هیدروکسید‌سدیم 5 به 1 انجام شد. پس از پخت، خمیرکاغذ‌ها توسط پالایشگر آزمایشگاهی PFI  تا رسیدن به درجة‌روانی 25 ± 380 میلی‌لیتر (CSF) پالایش شدند و بازده کل و عددکاپای آنها تعیین گردید. کاغذ دست‌ساز 60 گرمی براساس آئین‌نامه TAPPI ساخته شد و ویژگی‌های فیزیکی، نوری و مقاومتی ارزیابی شدند. نتایج نشان داد که پیش‌تیمار قلیایی اثر معنی‌داری در افزایش ویژگی‌های نوری و مقاومتی کاغذ داشته است. اندازه‌گیری درجه‌روانی اولیه خمیر کاغذها نشان داد که درجه‌روانی با افزایش مواد شیمیایی پخت و هیدروکسیدسدیم کاهش یافته و با افزایش مواد شیمیایی، دانسیته کاغذ افزایش، و بازده و ضخامت و حجم ویژه کاغذ کاهش یافت. }, keywords_fa = {کاه گندم,خمیرکاغذ نیمه شیمیایی سولفیت خنثی,درجه روانی}, url = {https://ijwpr.areeo.ac.ir/article_2952.html}, eprint = {https://ijwpr.areeo.ac.ir/article_2952_117eb88cdb53e379cc09264e9fcf69bc.pdf} } @article { author = {Kargarfard, Abolfazl and Nourbakhsh, Amir and Golbabaei, Fardad}, title = {Utilization of pomegranate tree pruning in the core layer of particleboard produced from Eucalyptus camedulensis wood}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {28}, number = {2}, pages = {381-391}, year = {2013}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2013.2953}, abstract = {The objective of this study was to investigate utilization of pomegranate pruning  residues as the core layer of the three layer particleboard. The percentage of the pomegranate residues varied as 100, 65 and 35% in the core layer of the eucalypt  particleboard and three resin levels of 8, 10 and 12 % (based on the weight of the wood particles) were applied in the core layer. Resin dosage in the surface layer was kept at 12 %. The strength and physical properties were measured and analyzed applying factorial model based on completely randomized design. The results revealed that if 65% pomegranate residues are used in the core layer, the modulus of rupture and modulus of elasticity were the highest and the combined effect of both variables on the properties were statistically significant. The highest value of the modulus of rupture and modulus of elasticity obtained in the case of 10% resin in the core layer and 100% pomegranate residues followed by 8% resin in the core layer and 65% pomegranate residues. The combined effect of both variables on internal bonding of the boards was statistically significant and the highest internal bonding was reached if 8% resin and 65% pomegranate residues were used in the core layer.  The effect of resin dosage on thickness swelling after 24 hours immersion in water was statistically significant. The results indicated that pomegranate tree pruning could be used for the particleboard manufacturing.  }, keywords = {Particleboard,pomegranate tree pruning,Eucalyptus,resin dosage,Strength}, title_fa = {امکان استفاده از پسماند لیگنوسلولزی حاصل از هرس درختان انار در لایه میانی تخته خردهچوب ساخته شده از چوب اکالیپتوس کاملدولنسیس}, abstract_fa = {این بررسی با هدف کاربرد پسماندهای لیگنوسلولزی حاصل از هرس درختان انار در لایه میانی تخته خرده‌چوب انجام شد. بنابراین با مقادیر متفاوت 100، 65 و 35 درصد سرشاخه انار در لایه میانی کیک حاوی خرده‌چوب اکالیپتوس و استفاده از 3 مقدار مصرف چسب 8، 10 و 12 درصد در لایه میانی و مصرف 12 درصد به‌طور ثابت در لایه سطحی، اقدام به ساخت تخته خرده‌چوب گردید. نتایج حاصل از آزمایش‌های فیزیکی و مکانیکی تخته‌های ساخته شده با استفاده از طرح آزمایش فاکتوریل در قالب طرح کامل تصادفی مورد تجزیه و تحلیل قرار گرفت. نتایج نشان داد که در شرایط استفاده از 65 درصد چوب سرشاخه انار در لایه میانی مقاومت‌خمشی و مدول‌الاستیسیته تخته‌ها به حداکثر رسید. همچنین اثر متقابل میزان مصرف چسب و خرده‌چوب انار بر مقاومت‌خمشی و مدول الاستیسیته تخته‌ها معنی‌دار بود، به‌طوری‌که بیشترین مقاومت‌خمشی و مدول‌الاستیسیته تخته‌ها به‌ترتیب با مصرف 10 درصد چسب و 100 درصد خرده‌چوب انار در لایه میانی، و مصرف 8 درصد چسب و 65 درصد چوب خرده‌چوب انار به‌دست آمد. اثر متقابل میزان مصرف چسب و مصرف خرده‌چوب انار بر مقاومت چسبندگی‌داخلی نیز معنی‌دار بود و حداکثر این ویژگی در شرایط مصرف 8 درصد چسب و 65 درصد خرده‌چوب انار در لایه میانی حاصل شد. همچنین با افزایش مصرف چسب در لایه میانی به طور معنی‌داری از واکشیدگی ضخامت 24 ساعت تخته‌ها کاسته شد. نتایج این بررسی امکان تولید تخته خرده‌چوب با ویژگی‌های استاندارد را با استفاده از سرشاخه‌های چوب انار مورد تأئید قرار داد.  }, keywords_fa = {تخته خردهچوب,چوب انار,اکالیپتوس,میزان مصرف چسب,ویژگیهای فیزیکی و مکانیکی}, url = {https://ijwpr.areeo.ac.ir/article_2953.html}, eprint = {https://ijwpr.areeo.ac.ir/article_2953_4dd250048e0bf55d24291ba2fefe7736.pdf} }