per
موسسه تحقیقات جنگلها و مراتع کشور
تحقیقات علوم چوب و کاغذ ایران
1735-0913
2383-112X
2016-03-20
31
1
1
13
10.22092/ijwpr.2015.105604
105604
Research Paper
تاثیر سیانواتیلاسیون خمیرکاغذ و نانوالیاف سلولزی بر خواص فیزیکی کاغذهای عایق ترانسفورماتور
The effect of pulp and cellulose nanofiber cyanoethylation on the physical properties of transformer insulating paper
محمد آزادفلاح
adfallah@ut.ac.ir
1
حمید خدابنده لو
h_khodabandeh@ut.ac.ir
2
امیر عباس شایگانی اکمل
shayegani@ut.ac.ir
3
استادیار، گروه علوم و صنایع چوب و کاغذ، دانشکده منابع طبیعی، دانشگاه تهران، کرج
کارشناس ارشد صنایع خمیر و کاغذ، دانشکده منابع طبیعی، دانشگاه تهران، کرج
استادیار، گروه مهندسی برق، دانشکده مهندسی برق و کامپیوتر، دانشگاه تهران
خواص کاغذهای عایق الکتریکی ترانسفورماتور متأثر از فرایند اصلاح شیمیایی انجام شده بر روی الیاف است. در این تحقیق تأثیر سیانواتیلاسیون خمیرکاغذ و افزودن نانوالیاف سلولزی سیانواتیلدار شده بر خواص دیالکتریک شامل ظرفیت، تلفات دیالکتریک، مقاومت عایقی، ولتاژ شکست و همچنین مقاومت به کشش دو نوع کاغذ دستساز تهیهشده از خمیرکاغذ رنگبرینشده الیاف بلند و ترکیبی از آن با خمیرکاغذ سودای باگاس با نسبت 1:1 پس از آغشتهسازی با روغن معدنی ارزیابی شده است. برای این منظور سیانواتیلاسیون نانوالیاف سلولزی و خمیرکاغذ توسط پیوندزنی با آکریلونیتریل بهترتیب در دمای C˚40 و دمای اتاق در شرایط قلیایی انجام شد. پسازآن میزان نیتروژن نمونههای سیانواتیلدار شده با روش کجدال تعیین و درجه استخلاف آنها محاسبه شد. نتایج نشان داد که سیانواتیلاسیون خمیرکاغذ و افزودن نانوالیاف سلولزی اصلاحشده موجب کاهش ظرفیت و مقاومت به کشش کاغذهای عایق شد. همچنین مشاهده شد که اصلاح شیمیایی تأثیر اندکی بر تلفات دیالکتریک داشته ولی مقاومت عایقی و ولتاژ شکست کاغذها را افزایش داده است.
The properties of transformer electrical insulating papers are influenced by fiber chemical modification process. In this research, the effect of cyanoethylation of fibers and addition of cyanoethylated cellulose nanofiber (CNF) on dielectric properties including capacitance, dielectric loss, insulation resistance, breakdown voltage as well as tensile strength of two grade of handsheets made of unbleached long fibers and its mixture with bagasse soda pulp (with the ratio of 1:1) were evaluated after impregnating with mineral oil. Cyanoethylation of CNF and pulp fibers was performed by grafting of acrylonitrile under alkaline condition at 40 ̊C and room temperature respectively. Then, the nitrogen content of cyanoethylated samples was determined using Kjeldahl method and degree of substitution (DS) was calculated. The results showed that cyanoethylation of pulp fibers and CNF decreased the capacitance and tensile strength of insulated papers. It was also observed that the chemical modification imposed slight effect on dielectric loss, but insulation resistance and dielectric voltage were increased.
https://ijwpr.areeo.ac.ir/article_105604_a66c7aa0f491423ff43b8a309235774e.pdf
سیانواتیلاسیون
کاغذ عایق
نانوالیاف سلولزی
خواص دیالکتریک
Cyanoethylation
insulation paper
cellulose nanofiber
dielectric properties
per
موسسه تحقیقات جنگلها و مراتع کشور
تحقیقات علوم چوب و کاغذ ایران
1735-0913
2383-112X
2016-03-20
31
1
14
29
10.22092/ijwpr.2015.105613
105613
Research Paper
تاثیر دیاکسید سیلسیوم بر دوام طبیعی و ریختشناسی چندسازه چوب پلاستیک در برابر قارچ رنگینکمان (Trametes Versicolor)
Effect of silica dioxide on natural resistance and morphological study of wood plastic composite against of white rot fungi (Trametes Versicolor)
سعید اسمعیلی مقدم
saeed.am17358@gmail.com
1
افسانه شهرکی
shahreki.afsaneh68@yahoo.com
2
فاطمه دهدست
fatima.dehdast61@gmail.com
3
سمانه پور کرمی
pourkarami64@yahoo.com
4
باشگاه پژوهشگران جوان و نخبگان، دانشگاه آزاد اسلامی، واحد چالوس، چالوس، ایران.
دانشآموخته کارشناسی ارشد فرآوردههای چندسازه چوب، دانشگاه زابل
دانش آموخته کارشناسی ارشد فرآورده های چندسازه چوب دانشگاه زابل
دانش آموخته کارشناسی ارشد حفاظت و اصلاح چوب دانشگاه علوم کشاورزی و منابع طبیعی گرگان
این تحقیق با هدف بررسی تأثیر افزودن ذرات سیلیس بر دوام طبیعی و ریختشناسی چندسازه چوب پلاستیک در برابر قارچ رنگینکمان (Trametes Versicolor) انجام شد. آرد چوب با نسبت وزنی 60 درصد با پلیپروپیلن به همراه phc 2 انیدرید مالئیک پلیپروپیلنی مخلوط گردید. نانو و میکرو سیلیس نیز با نسبتهای وزنی 0، 1، 3 و phc 5 بهعنوان پرکننده مورد استفاده قرار گرفتند. فرایند اختلاط در داخل دستگاه مخلوطکن داخلی انجام شد و نمونههای آزمونی با استفاده از دستگاه تزریق ساخته شدند. نمونههای آزمونی به مدتهای 8، 12 و 16 هفته در مجاورت قارچ رنگینکمان با دمای 25 درجه سانتیگراد و رطوبت نسبی 75 درصد مطابق با استاندارد BS 838:1961 قرار گرفتند. سپس کاهش جرم، جذب آب بلندمدت و ضریب انتشار رطوبت بر روی نمونهها انجام شد. برای اطمینان از تشکیل پیوند هیدروژنی بین سیلیس و آرد چوب از طیفسنجی مادون قرمز (FTIR) و برای ریختشناسی چندسازهها از میکروسکوپ الکترونی پویشی (SEM) استفاده گردید. نتایج نشان داد که با افزایش زمان مجاورت نمونهها در محیط قارچ، کاهش جرم، جذب آب بلندمدت و ضریب انتشار رطوبت در چوب پلاستیک افزایش یافت، اما با افزایش سیلیس، از شدت پوسیدگی نمونهها کاسته شد. تأثیر نانو ذرات سیلیس بر دوام طبیعی چندسازه چوب پلاستیک بیشتر از تأثیر میکرو ذرات سیلیس بود. نتایج طیفسنجی مادون قرمز حکایت از ایجاد پیوند هیدروژنی بین آرد چوب و سیلیس داشت. نتایج میکروسکوپ الکترونی پویشی نیز نشان داد که با افزایش مجاورت نمونهها با قارچ ترکهای ریز و درشتی در چندسازه ایجاد گردید اما با افزایش سیلیس از میزان این ترکها کاسته شد.
The objective of this study was the evaluation of the addition of silica particles in composite on natural resistance and morphology of wood plastic composite against of white rot fungi (Trametes Versicolor). Wood flour at the ratio of 60% (w/w), polypropylene and 2 per hundred compound (phc) MAPP was mixed. Nano and micro silica at 0, 1, 3 and 5 (phc) were added as filler. The mixing process in internal mixer (HAAKE) was done and test specimens were prepared using injection molding. The test specimens were exposed to Trametes Versicolor fungi for 8, 12 and 16 weeks at 25 oC and 75% humidity according to BS 838:1961. Then the mass loss, long-term water absorption and humidity coefficient diffusion of the samples were measured. The formation of hydrogen bonds between silica and wood flour was determined by Fourier Transform Infrared (FTIR) spectroscopy and the morphology of composite was stydied using scanning electron microscopy (SEM). The result showed that with increasing period of samples exposure to fungi, the mass loss, long-term water absorption and humidity coefficient diffusion in wood plastic composite increased. However at higher silica, decay in the samples was decreased. The effect of silica nanoparticles on natural resistance of wood plastic composite was higher than sample containing silica micro particles. Infrared spectroscopy showed hydrogen bonds between wood flour and silica. The result of scanning electron microscopy showed that with increasing of exposure time to fungi, small and large cracks in composite were created. However increasing silica addition, these cracks were decreased.
https://ijwpr.areeo.ac.ir/article_105613_516c51c5fab7b01e5da5826ea1d43dc9.pdf
دوام طبیعی
ضریب انتشار رطوبت
قارچ رنگین کمان
نانو و میکرو سیلیس
کاهش وزن
Natural resistance
humidity coefficient diffusion
TRAMETES VERSICOLOR
nano and micro silica
mass loss
per
موسسه تحقیقات جنگلها و مراتع کشور
تحقیقات علوم چوب و کاغذ ایران
1735-0913
2383-112X
2016-03-20
31
1
30
39
10.22092/ijwpr.2015.105771
105771
Research Paper
تأثیر استفاده از آرد نخل خرما در ساخت کامپوزیت چوب-پلاستیک بر پایه پلی پروپیلن
The effect of using Palm Flour in the Manufacture of pp-based wood-plastic Composite
علیرضا بی اذیت
alirezabiazyat@gmai.com
1
لعیا جمالی راد
loyajamalirad@yahoo.com
2
هدایت الله امینیان
hedaminian@yahoo.com
3
سحاب حجازی
shedjazi@ut.ac.ir
4
کارشناس ارشد گروه علوم و صنایع چوب و کاغذ، دانشکده کشاورزی و منابع طبیعی، دانشگاه گنبدکاووس
استادیار، گروه علوم و صنایع چوب و کاغذ، دانشکده کشاورزی و منابع طبیعی، دانشگاه گنبدکاووس
استادیار، گروه علوم و صنایع چوب و کاغذ، دانشکده کشاورزی و منابع طبیعی، دانشگاه گنبدکاووس
دانشیار، گروه علوم و صنایع چوب و کاغذ، دانشکده منابع طبیعی، دانشگاه تهران
در این تحقیق، تأثیر مقدار پرکننده و ماده جفت کننده MAPP بر ویژگیهای فیزیکی و مکانیکی کامپوزیت پلیپروپیلن تقویت شده شده با آرد حاصل از ضایعات ناشی از هرس سالیانه برگ نخل خرما (رقم شاهانی) مورد مطالعه قرار گرفت. بدین منظور استفاده از سه سطح 30، 40 و 50 درصد آرد نخل خرما و دو سطح 4 و 6 درصد MAPP به عنوان عوامل متغییر در نظر گرفته شد. سپس خواص فیزیکی و مکانیکی نمونههای آزمونی شامل واکشیدگی ضخامت بعد از 2 و 24 ساعت غوطه وری در آب، مقاومت و مدول کششی، مقاومت و مدول خمشی و مقاومت به ضربه اندازهگیری شد. نتایج حاصل نشان داد که با افزایش آرد نخل خرما مقاومت خمشی، مقاومت کششی و مقاومت به ضربه کاهش و در مقابل واکشیدگی ضخامت، مدول خمشی، مدول کششی افزایش یافتهاند. همچنین با بررسی اثر ماده جفت کننده مشخص گردید که با افزودن MAPP واکشیدگی ضخامت، مقاومت و مدول الاستیسیته کششی و خمشی کامپوزیت حاصل بهبود یافته است. این بدان معنی است که همراه با افزایش مصرف آرد نخل خرما، افزودن عامل جفت کننده منجر به بهبود کیفیت سطح مشترک شده و تغییرات قابل ملاحظهای را خصوصا در پایداری ابعادی و مدول الاستیسیته حاصل کرده است.
In this research, the effect of the wood filler content and coupling agent (MAPP) on the physical and mechanical properties of Polypropylene reinforced with palm wood flour from the annual pruning of palm leaves (Shahani species) composite, were studied. For this purpose, the palm wood flour in three levels of 30%, 40%, 50% and two levels of Maleic anhydride grafted polypropylene 4% and 6% were used as variable factors. Then, the Physical and mechanical properties of samples, including thickness swelling after 2 and 24 hours of immersion in water, bending strength, bending modulus, tensile strength, tensile modulus and impact strength, were measured.The results showed that by increasing palm wood flour, the bending strength, tensile strength and impact strength were decreased but the thickness swelling, bending modulus, tensile modulus were increased. It was also found that by adding MAPP, thickness swelling, bending strength, bending modulus, tensile strength and tensile modulus were improved. The results revealed that at increased consumption of palm wood flour and adding coupling agent leads to improve quality of the interface and significant changes especially dimensional stability and MOE, are achieved.
https://ijwpr.areeo.ac.ir/article_105771_875e8e51b9365eea973c05b722dbdc7d.pdf
کامپوزیت
پلیپروپیلن
آرد نخل خرما
جفت کننده
مدول الاستیسیته
Composite
Polypropylene
Palm flour
Coupling agent
Modulus of Elastisity
per
موسسه تحقیقات جنگلها و مراتع کشور
تحقیقات علوم چوب و کاغذ ایران
1735-0913
2383-112X
2016-03-20
31
1
40
47
10.22092/ijwpr.2015.102672
102672
Research Paper
تاثیر اسید بوریک بر روی خواص فیزیکی و مکانیکی تخته خرده چوبهای ساخته شده با رزین اوره فرمالدهید (UF)
The effect of boric acid on the physical and mechanical properties of particleboard made to Urea-formaldehyde resin (UF)
مصطفی پوزش
mostafapoozesh67@gmail.com
1
حمیدرضا منصوری
hamidreza.mansouri@gmail.com
2
بابک نصرتی
nosrati.babak@uoz.ac.ir
3
علیرضا سام زاده
4
دانشجوی کارشناسی ارشد فرآوردههای چند سازه چوبی دانشگاه زابل
استادیار گروه علوم و صنایع چوب و کاغذ دانشگاه زابل
استادیار، گروه علوم و صنایع چوب و کاغذ، دانشگاه زابل
عضو هیات علمی استادیار، گروه شیمی دانشگاه زابل
هدف از انجام این پژوهش بررسی مقاومت در برابر آب تخته خرده چوبهای ساخته شده با رزین اوره فرمالدهید (UF) به کمک افزودن اسید بوریک به این رزین بود. در این بررسی افزودنی مورد نظر به عنوان عامل متغیر در چهار سطح 1، 2، 3 و 4 درصد نسبت به وزن خشک چسب استفاده شد. پس از تهیه فراوردههای مرکب، مقاومتهای فیزیکی و مکانیکی بر اساس استاندارد ASTM, D1013-04 مورد بررسی قرار گرفت. نتایج نشان داد که استفاده از این افزودنی موجب افزایش مقاومت در برابر آب و واکشیدگی ضخامت 2 و 24 ساعت بعد از غوطهوری در آب، در تخته خرده چوبهای ساخته شده با این رزین شد. همچنین استفاده از این افزودنی مقاومت چسبندگی 24 ساعت غوطهوری در آب نسبت به نمونه شاهد افزایش داد، اما در حالت خشک نسبت به نمونه شاهد باعث کاهش شد، هرچند این کاهش پایینتر از حد استاندارد نبود. با افزایش سطوح اسید بوریک تا 2 درصد مقاومت خمشی نمونههای ساخته شده نسبت به نمونه شاهد افزایش، و بعد از این سطح کاهش یافت. احتمال میرود این کاهش به علت تاثیر اسید بوریک بر روی الیاف سلولزی یا فیبر سلولزی باشد در اثر گرما باعث تخریب این الیاف و کم شدن مقاومت خمشی میشود. همچنین با افزایش سطوح افزودنی ذکر شده تا سطح 4 درصد مدول الاستیسیته تخته-های ساخته شده نسبت به نمونه شاهد افزایش یافت.
This objective of this investigation was to modify and improve the water resistance of urea formaldehyde (UF) bonded particleboard adding Boric acid to the resin. Four levels (1, 2, 3 and 4) of boric acid based on the dry weight of the bonder were added to the UF resin. Then these mixtures were used to produce particleboard. Physical and mechanical properties were examined according to the ASTM, D1013-04. The results showed that the using of this additive increased the water absorption and thickness swelling resistance after 2 and 24 hours immersion in water. Also using this additive increased the internal bonding of the boards after 24 hours after immersion in water, compared to the control sample but in the case of dry samples, the internal bonding decreased compared to the control sample. However it was not lower than standard value. As the Boric acid levels increased to 2 percent, bending strength of the samples was increased compare to the control sample and after this level it was decreased. Also with increasing the levels to 4 percent, modulus of elasticity of boards were increased compare to the control sample
https://ijwpr.areeo.ac.ir/article_102672_b252aa25a6530a718d8be6e90b4c4b5c.pdf
اوره فرمالدهید
اسید بوریک
جذب آب
واکشیدگی ضخامت
چسبندگی داخلی
UREA FORMALDEHYDE
Boric acid
water absorption
Thickness swelling
Internal bonding
per
موسسه تحقیقات جنگلها و مراتع کشور
تحقیقات علوم چوب و کاغذ ایران
1735-0913
2383-112X
2016-03-20
31
1
48
57
10.22092/ijwpr.2015.105608
105608
Research Paper
تأثیر استفاده از خمیر مرکب زدایی شدهی مخلوط کاغذهای باطلهی اداری(MOW) بر ویژگیهای خمیر کاغذ مکانیکی پروکسید قلیایی(APMP) ساقهی پنبه
The effect of using deinked mixed office waste pulp on the properties of Alkaline
Proxide Mechanical Pulp from cotton stalk
مهرنوش توکلی
tavakolimehrnoosh@yahoo.com
1
احمدرضا سرائیان
saraeyan@yahoo.com
2
حسین رسالتی
hnresalati@yahoo.com
3
علی قاسمیان
ali.ghasemian1960@yahoo.com
4
کارشناس ارشد خمیرکاغذ دانشگاه علوم کشاورزی و منابع طبیعی گرگان
دانشیار، علوم و تکنولوژی خمیر و کاغذ، دانشگاه علوم کشاورزی و منابع طبیعی گرگان
استاد راهنما/ دانشگاه علوم کشاورزی و منابع طبیعی گرگان
استاد راهنما/ دانشگاه علوم کشاورزی و منابع طبیعی گرگان
این تحقیق با هدف بررسی تأثیر استفاده از خمیرکاغذ مرکبزدایی شدهی مخلوط کاغذهای باطلهی اداری (MOW) بر ویژگیهای خمیرکاغذAPMP ساقهی پنبه انجام گرفت. به این منظور خمیرکاغذهای APMP با استفاده از عوامل کیلیتساز نظیر سیلیکات سدیم و DTPA (نمونه شاهد) و بدون استفاده از این ترکیبات ازخردههای ساقه پنبهی بدون پوست در دو مرحله با نسبت مایع خمیرسازی به ماده اولیه 1 : 6، زمان 20 دقیقه و درجه حرارت C°70 در مرحله اول، زمان 60 دقیقه و درجه حرارت C° 75 در مرحله دوم تهیه شدند. علاوه بر این خمیرکاغذهای حاصل از مخلوط کاغذهای باطله اداری که با روش متداول شناورسازی مرکبزدایی شدند، تهیه شده و تا رسیدن به درجه روانی حدودml CSF 300 پالایش شدند. از خمیرکاغذ-های شاهد، بدون استفاده از عوامل کیلیتساز، خمیرکاغذ مرکبزدایی شدهی مخلوط کاغذهای باطلهی اداری و همچنین اختلاط 10% و 20% آن با APMP شاهد کاغذهای دستساز ساخته شد. ویژگیهای فیزیکی و مکانیکی کاغذها بر اساس استانداردهای تاپی تعیین گردید. بیشترین مقادیر دانسیته، درجه روشنی و ویژگیهای مقاومتی مربوط به خمیرکاغذ مرکبزدایی شدهی MOW و کمترین مقادیر مربوط به خمیرکاغذ APMP بدون عوامل کیلیتساز بود و از بین کاغذهای اختلاطی نیز خمیرکاغذAPMP حاوی 20% خمیر مرکبزدایی شده MOW بیشترین مقادیر دانسیته، درجه روشنی، شاخص مقاومت به ترکیدن و پاره شدن را داشت.
The present study was carried out aiming to investigate the effect of using Deinked Mixed Office Waste Pulp (MOW) on the properties of Alkaline Peroxide Mechanical Pulp (APMP) from cotton stalk. APMP pulps was prepared using chelating agents such as Na2SiO3 and DTPA (control sample) and without these agents in two-stage pulping withL/Wratio 6:1(ml/g), 20 minutes impregnation time at 70 0Cfor firststage, 60 minutes impregnation at 75 0Cfor second stage. Also, pulp was preparedfrommixed office waste paper, whichweredeinked with conventional flotation and then each pulp was separately refined up to about 300 ml CSF. The handsheets were made from control sample pulps, APMP without chelating agents, MOW deinked pulp and mixing with 10%, 20% deinked pulp with control APMP. Physical and mechanical properties were determined using TAPPI standard methods. Deinked MOW pulp had the maximum values of density, brightness, strength properties and APMP pulp without chelating agents had the minimum values. Among mixed pulps, APMP pulp containing 20% deinked MOW pulp showed the maximum value of density, brightness, burst index and tear index.
https://ijwpr.areeo.ac.ir/article_105608_76ca5fb209d2a7cb4e0861d7737dd018.pdf
خمیرکاغذAPMP
ساقه پنبه
خمیر مرکبزدایی شده MOW
دانسیته
درجه روشنی
شاخص مقاومت به ترکیدن
APMP pulp
COTTON STALK
Deinked pulp of MOW
Density
brightness
BURST INDEX
per
موسسه تحقیقات جنگلها و مراتع کشور
تحقیقات علوم چوب و کاغذ ایران
1735-0913
2383-112X
2016-03-20
31
1
58
66
10.22092/ijwpr.2015.105610
105610
Research Paper
بررسی تاثیرزمان ذخیرهسازی بر خواص رنگ و ترکیبات شیمیایی تخته خرده حاصل از باگاس
Investigation of the storage time on color properties and chemical compositions of particle board made from bagasse
مهدی جنوبی
mehdi.jonoobi@ut.ac.ir
1
شوبو صالحپور
shsalehpur@yahoo.com
2
زهره عرازنیا
araznia@yahoo.com
3
یحیی همزه
hamzeh@ut.ac.ir
4
استادیار، گروه علوم و صنایع چوب و کاغذ، دانشکده منابع طبیعی، دانشگاه تهران،
دانشجوی دکتری، گروه علوم و صنایع چوب و کاغذ، دانشکده منابع طبیعی، دانشگاه تهران
دانشآموخته کارشناسی ارشد، گروه علوم و صنایع چوب و کاغذ، دانشکده منابع طبیعی، دانشگاه تهران
استاد، گروه علوم و صنایع چوب و کاغذ، دانشکده منابع طبیعی، دانشگاه تهران
این تحقیق، با هدف بررسی تاثیر ذخیرهسازی بر خواص رنگ و ترکیبات شیمیایی تخته خرده حاصل ازباگاسانجام شد. برای این منظور از باگاس ذخیره شده کارخانه نئوپان کارون واقع در استان خوزستان درسه سطح (بالا،وسط وپائین) و باگاس ذخیرهنشده تهیه گردید. سپس،ترکیبات شیمیایی نمونهها براساس دستورالعمل TAPPI، ویژگی بیومتری (ضریبلاغری) با استفاده از روش فرانکلین و تغییرات رنگ آنها اندازهگیری شد. همچنین شناسایی نوع میکروارگانسیمهای موجوددرنمونههای باگاس دخیره شده در سه سطح انجام گرفت، نتایج با نمونهها شاهد مقایسه شد. نتایج نشان داد، که مقدارلیگنین دربین نمونههای باگاس ذخیرهشده درسه سطح تفاوت داشت،اماتفاوتی معنیداری درمیزان سلولزومواداستخراجی آنهامشاهده نشد. همچنین در ضریب لاغری نمونهها(ذخیره شده و دخیره نشد)تفاوتی ملاحظه نشد. میزان تغییررنگ درتختههای ساختهشده ازباگاس ذخیرهشدهبیشترازنمونههایذخیرهنشدهبود. بررسیهای شناسایی نوع میکروارکانسیمهای موجوددرنمونههای باگاس ذخیرهشده نشان دادکه بیشترین آنهاباکترهای ومخمرهابودند. نتایج ازمایشات انجام شده نشان داد که مدت ذخیره سازی می تواند به طور چشمگیری رنگ و خواص فیزیکی باگاسهای ذخیره شده را مورد تغییر قرار دهد.
This study was carried out to investigate the effect of storage time on the color and chemical compounds of bagasse particleboard made. For this purpose, the three levels of stored and fresh bagasse from karoon particleboard Company were used. In addition, the chemical compositions were determined according to the TAPPI test methods and also biometrical (slenderness ratio) was done using the fiber dimension measured by Franklin method. The results showed that the amount of lignin was different in the stored samples at three levels, but the difference in the amount of cellulose and extractive was not observed. The results illustrated that the color changes in the stored bagasse were more than fresh sample. Identification of the microorganisms in stored samples was done and results showed that most of microorganisms were bacteria and yeast. The results showed that the storage time can significantly effect the color and physical properties of stored bagasse.
https://ijwpr.areeo.ac.ir/article_105610_e83559cd3d6187e25af3af4ac51f7e01.pdf
باگاس
ذخیرهسازی
تغییرات رنگ
ترکیبات شیمیایی
Bagasse
Storage
Color changes
chemical compounds
per
موسسه تحقیقات جنگلها و مراتع کشور
تحقیقات علوم چوب و کاغذ ایران
1735-0913
2383-112X
2016-03-20
31
1
67
77
10.22092/ijwpr.2015.102674
102674
Research Paper
بررسی ویژگیهای کششی و ثبات ابعادی چندسازه پلیپروپیلن/الیاف کاه گندم/ لجن کارخانه کاغذ
Investigation on the tensile properties and dimensional stability of polypropylene/wheat straw fiber/paper mill sludge composites
حبیب الله خادمی اسلام
hkhademieslam@gmail.com
1
مهدی کلاگر
mehdi.kalagar@gmail.com
2
دانشیار گروه علوم و صنایع چوب و کاغذ، واحد علوم و تحقیقات تهران، دانشگاه آزاد اسلامی
دکتری صنایع چوب و کاغذ، کارشناس جنگل، شرکت جنگل شفارود، گیلان
در این مطالعه ویژگیهایی کششی و فیزیکی چندسازه پلیپروپیلن (بهعنوان ماتریس) و الیاف کاه گندم/ لجن کارخانه کاغذ (بهعنوان پرکننده) مورد بررسی قرار گرفته است. برای ساخت چندسازه از ترکیبات مختلف الیاف کاه گندم/لجن کارخانه کاغذ (40/0، 30/10، 20/20، 10/30 و 0/40) استفاده شد. همچنین برای سازگاری بهتر بین دو فاز از انیدریدمالئیک پیوند خورده با پلی پروپیلن به میزان 3% بهعنوان اتصال دهنده استفاده شد. برای اختلاط مواد از اکسترودر دو مارپیچ ناهمسانگرد و برای تهیه نمونههای استاندارد از روش قالبگیری تزریقی استفاده شد. بررسی مدولالاستسیته کششی نشان که با افزودن هر دو نوع پرکننده افزایش قابل توجهای در سفتی چندسازه نسبت به PP خالص مشاهده شده در حالیکه بالاترین مدول الاستسیته کششی مربوط با چندسازه با درصد بالاتر لجن کارخانه کاغذ بوده است. مقاومت کششی چندسازه با افزودن 40% الیاف کاه گندم کاهش یافت اما پس از آن با افزودن بالاتر لجن کارخانه کاغذ مقاومت کششی چندسازه افزایش معنیداری را نشان داده است. با افزودن الیاف کاه گندم به ماتریس PP و دارا بودن خاصیت آبدوستی این مواد بالاترین میزان جذب آب و واکشیدگی ضخامت مشاهده شد. در حالیکه با افزودن لجن کارخانه کاغذ با میزان مواد لیگنوسلولزی کمتر، پایینترین میزان جذب آب و واکشیدگی ضخامت مشاهده شد. هم-چنین با افزودن اتصال دهنده و برقراری اتصال بهتر بین دو فاز کاهش قابل توجهای در جذب آب و واکشیدگی ضخامت مشاهده شد. کلمات کلیدی: الیاف کاه گندم، لجن کارخانه کاغذ، ویژگیهای کششی، ثبات ابعادی، چندسازه
In this investigation, tensile and physical properties of polypropylene (as matrix)/wheat straw fiber/paper mill sludge (as filler) composites was studied. The ratio of wheat straw fiber/ paper mill sludge was selected as 40/0, 30/10, 20/20, 10/30 and 0/40 (w/w) were used. Also, for better compatibility between the two phases 3% MAPP as coupling agent was used. Mixing process was done in twin screw internal mixer extruder, and then composite samples were manufactured by injection molding. Result indicated that the tensile modulus of elasticity improved with increasing fillers and also it was observed that the toughness of composite increased when compared to the pure PP, while due to the usage of more paper sludge, these properties was improved. Tensile strength of composite decreased with adding 40% wheat straw fiber, but with addition of sludge tensile strength increased significantly. Adding wheat straw in PP matrix and its hydrophilic properties resulted in the highest rates of water absorption and thickness swelling. However, adding paper sludge and lower amount of lignocellulosic material, and the compatibilizer noticeably decreased the physical properties due to better bonding between two phases.
https://ijwpr.areeo.ac.ir/article_102674_4effbb9bccda9cf623c6e4b65a26fb80.pdf
الیاف کاه گندم
لجن کارخانه کاغذ
ویژگیهای کششی
ثبات ابعادی
چندسازه
wheat straw fiber
paper mill sludge
tensile properties
Dimensional stability
Composite
per
موسسه تحقیقات جنگلها و مراتع کشور
تحقیقات علوم چوب و کاغذ ایران
1735-0913
2383-112X
2016-03-20
31
1
78
91
10.22092/ijwpr.2015.105607
105607
Research Paper
بررسی ویژگیهای چندسازههای زیستی خمیرکاغذ- پلی پروپیلن از باگاس خام و پیش استخراج شده با آب داغ
The Study of Pulp-Polypropylene biocomposites Properties produced from non-extracted and pre-extracted Bagasse with hot water
علیرضا سوخته سرائی
sukhtesaraee@ut.ac.ir
1
سحاب حجازی
shedjazi@ut.ac.ir
2
لعیا جمالی راد
loyajamalirad@yahoo.com
3
محمد احمدی
mohammad@ut.ac.ir
4
سید بهنام حسینی
behnamhosseini@ut.ac.ir
5
دکترای صنایع خمیر و کاغذ، دانشکده منابع طبیعی دانشگاه تهران
دانشیار، گروه علوم و صنایع چوب و کاغذ، دانشکده منابع طبیعی دانشگاه تهران
استادیار، گروه علوم و صنایع چوب و کاغذ، دانشکده کشاورزی و منابع طبیعی، دانشگاه گنبد کاووس
استادیار گروه صنایع چوب و کاغذ،دانشگاه محقق اردبیلی
دانشآموخته کارشناسی ارشد مهندسی خمیر و کاغذ، دانشکده منابع طبیعی دانشگاه تهران
در این پژوهش ویژگیهای فیزیکی و مکانیکی چندسازههای پلیپروپیلن تقویتشده با خمیرکاغذهای شیمیایی سولفیت قلیایی- آنتراکینون، سودا- آنتراکینون، مونواتانول آمین- آنتراکینون و خمیر کاغذ شیمیایی- مکانیکی حاصله از باگاس خام و پیش استخراج شده با آب داغ با استفاده از عامل جفتکننده مالئیک انیدرید- پلی پروپیلن به میزان 3 درصد و نسبت ماده زمینه پلیپروپیلن به ماده تقویتکننده خمیرکاغذ 50/50 درصد در نظر گرفته شد. نتایج نشان داد که نوع فرایند اثر معنیداری بر تمامی ویژگیهای مکانیکی و فیزیکیهای چندسازهها دارد. به طور کلی چندسازههای حاوی خمیر کاغذهای شیمیایی مقاومت و پایداری ابعادی بیشتر و جذب آب کمتری نسبت به نمونه حاوی خمیرکاغذهای مکانیکی دارا بودند.چندسازه های حاوی الیاف تیمار شده با فرآیندهای سولفیت قلیائی آنتراکینون و سودا بیشترین مقاومت های مکانیکی را دارا می باشند. چندسازههای ساخته شده از الیافی که همی سلولز آنها استخراج شده و با فرآیندهای شیمیائی تیمار شده اند بیشترین مقاومت و پایداری ابعادی را داشتند. در کل نتایج حاکی از بهبود ویژگیهای مقاومتی و فیزیکی چندسازههای خمیرکاغذ-پلاستیک در مقایسه با چندسازههای آرد ماده لیگنوسلولزی- پلاستیک میباشد.
In this study, the physical and mechanical properties of polypropylene composites reinforced with alkaline sulfite-anthraquinone, soda-anthraquinone and monoethanolamine-anthraquinone and chemical mechanical produced from non-extrated and pre-extracted bagasse with hot water were studied. MAPP coupling agent (3%) was added and the performance of pretreated and unpretreated bagasse composites were compared. The ratio of the polypropylene and reinforcement material (pulp) was considered at 50/ 50 (w/w). The results showed that the pulping process has a significant effect on all physical and mechanical properties of produced composites. In general, composites containing chemical pulps showed greater dimensional stability and mechanical strengths but lower water absorption than that of mechanical pulp. Composites containing treated fibers with alkaline sulfite-anthraquinone and soda pulp had the highest mechanical properties and dimensional stability. Composites made from fibers in which hemicelluloses were extracted and then were treated with chemical pulping processes had the highest mechanical strength and dimensional stability among all of samples. The highest mechanical strengths and dimensional stability were observed in composites which were reinforced with treated fibers compared with control samples containing untreated bagasse fibers. In general, the results showed the superior physical and mechanical characteristics for pulp - plastic composites compared with wood flour plastic composites.
https://ijwpr.areeo.ac.ir/article_105607_0c228219fd4c9f42aec1f6fb0f9eab6d.pdf
چندسازه
خمیرکاغذ
پلی پروپیلن
ویژگیهای فیزیکی و مکانیکی
Composite
pulp
Polypropylene
Mechanical and physical properties
per
موسسه تحقیقات جنگلها و مراتع کشور
تحقیقات علوم چوب و کاغذ ایران
1735-0913
2383-112X
2016-03-20
31
1
92
104
10.22092/ijwpr.2015.105606
105606
Research Paper
بررسی امکان ساخت نانوچندسازه ساخته شده از پباکس و نانوسلولز
Investigation on possibility of making a Nano composite consist of Pebax and Nano cellulose
حسن ضیائی طبری
hassanziaei64@gmail.com
1
حبیب الله خادمی اسلام
hkhademieslam@gmail.com
2
بهزاد بازیار
behzad1351@yahoo.com
3
امیرهومن حمصی
h_hemmasi@yahoo.com
4
دانشجوی دکتری دانشگاه ازاد اسلامی.واحد علوم و تحقیقات
هیات علمی دانشگاه آزاد واحد علوم و تحقیقات تهران
دانشیار، دانشگاه آزاد اسلامی، واحد علوم و تحقیقات، گروه صنایع چوب و کاغذ، تهران
استادیار، دانشگاه آزاد اسلامی، واحد علوم و تحقیقات، گروه صنایع چوب و کاغذ، تهران
در این تحقیق یک نوع جدید از نانو چند سازه الاستومر ترموپلاستیک تقویت شده با فیبرهای نانو سلولز گزارش می شود. هدف از این مطالعه ابتدا بررسی برهمکنش و پخش نانو سلولز در داخل ماتریکس پباکس بوده است. این کوپلیمر (پباکس)، ترموپلاستیک الاستومر پلی اتر بلاک آمید می باشد که از منابع تجدید شونده بدست می آید و خصوصیت آب دوستی (گروه های عاملی) آن منجر به برهمکنش آن با نانو سلولز می گردد. برهمکنش و اثر تقویت کنندگی نانو سلولز در سه سطح 1، 3 و 5 درصد به وسیله میکروسکوپ الکترونی پویشی، طیف سنجی مادون قرمز و آزمون های مکانیکی (شامل مدول یانگ، افزایش طول تا نقطه شکست و مقاومت به ضربه) مورد بررسی قرار گرفت. همه نتایج بدست آمده دلالت بر اثر مناسب فیبرهای نانو سلولز بر برهمکنش قوی و تماس نزدیک با بخش پلی آمید ماتریکس پباکس دارد که موجب افزایش خواص مکانیکی نانو چند سازه گردیده است. مدول یانگ و مقاومت به ضربه نانو چندسازه، افزایش چشمگیری پیدا کرد.
A new kind of thermoplastic elastomer nano composite reinforced with nano cellulose fibers is reported. The first aim of this investigation was to study the interaction and dispersion of nano cellulose fiber into Pebax matrix. This copolymer is Polyether – b – Amide thermoplastic elastomer which is synthetized from renewable resources, and its hydrophilic character allows it to interact with nano cellulose. The interaction and reinforcement effect of nano cellulose at 3 levels of nano cellulose (1%, 3% and 5%) were examined by Scanning electron microscopes (SEM), Fourier transform infrared spectroscopy (FTIR) and Mechanical tests (young module, elongation at break and impact resistance). The results achieved from these tests were indicating appropriate effects of nano cellulose fibers for the strong interaction and close contact with polyamide phase of Pebax polymer which caused high mechanical properties (at 3% of nanoellulose) in nano composites. The young module and impact resistance of nano composite were significantly increased.
https://ijwpr.areeo.ac.ir/article_105606_bc8b07d28a80fb5c2fb38eb04e80bdbd.pdf
ترموپلاستیک الاستومر
فیبر نانوسلولز
نانوچندسازه
SEM
FTIR
Thermoplastic elastomer
Nanocellulose fiber
nanocomposite
SEM
FTIR
per
موسسه تحقیقات جنگلها و مراتع کشور
تحقیقات علوم چوب و کاغذ ایران
1735-0913
2383-112X
2016-03-20
31
1
105
117
10.22092/ijwpr.2015.102671
102671
Research Paper
بررسی تأثیر استیلاسیون چوب راش بر مقاومت چسبندگی سطحی شفافپوشهها (سیلر،کیلر و نیم پلیاستر)
Studying the effect of acetylation Beech on interfacial bonding resistance of transparent paint (nitrocellulose lacquer, asid catalyzed lacquer and Half Ppolyester)
شهرام طهماسبی
shahram_541@yahoo.com
1
بهزاد بازیار
behzad1351@yahoo.com
2
حبیبالله خادمی اسلام
hkhademieslam@gmail.com
3
محمد غفرانی
ghofrani@sru.ac.ir
4
کارشناس ارشد، گروه صنایع چوب و کاغذ، دانشگاه آزاد اسلامی واحد علوم و تحقیقات تهران
استادیار گروه صنایع چوب و کاغذ، دانشگاه آزاد اسلامی واحد علوم و تحقیقات تهران
دانشیار گروه صنایع چوب و کاغذ، دانشگاه آزاد اسلامی واحد علوم و تحقیقات تهران
دانشیار گروه صنایع چوب، دانشکده عمران، دانشگاه تربیت دبیر شهید رجائی تهران
در این تحقیق تأثیر استیلاسیون چوب راش بر کاهش میزان چسبندگی سطحی رنگهای شفاف سیلر- کیلر و نیم پلیاستر مورد بررسی قرار گرفت. برای این منظور تختههایی از چوب راش (Orientalis Fagus) با رطوبت نسبی 12 درصد و ابعاد 12 ×110 ×110 میلیمتر در سطوح مماسی و شعاعی تهیه و توسط استیک انیدرید در دو سطح 5/12 و 5/15 درصد تیمار شدند، سپس طی دو فرایند جداگانه توسط رنگهای شفاف سیلر-کیلر و سیلر-نیمپلیاستر پوشش داده شدند. برای بررسی تأثیر فرایند استیلاسیون بر ساختار چوب تیمار شده از طیف FT-IR استفاده شد. نتایج این آزمون که توسط نرمافزار SPSS (6 تکرار برای هر نمونه) مورد تجزیهوتحلیل آماری قرار گرفت، نشان داد که میزان کاهش چسبندگی در سطح شعاعی چوب راش بیشتر از سطح مماسی آن است. البته در میان نمونههای تیمار شده، بیشترین کاهش چسبندگی مربوط به نمونههای استیله با شدت استیلاسیون 5/15 درصد میباشد و کمترین میزان کاهش چسبندگی در نمونههای کنترل ملاحظه شد. نتایج همچنین نشان داد که استفاده از پوشش رنگ سیلر- نیم پلیاستر در مقایسه با پوشش رنگ سیلر- کیلر دارای مقاومت چسبندگی بالاتری است.
In this study, structural performance of corner joint reinforced by fiber reinforced polymers (FRP) at the area of maximum tension stress was investigated under diagonal tension loading. Therefore 1 to 3 layers of unidirectional woven Glass, Carbon and Kevlar fibers were used and hand lay-up was done by vinyl ester and epoxy resins. Results of load-displacement curve at yield point exhibited capability of the reinforcing layers in preventing joint opening to some extent under load. However, failure was observed at the joint due to picking fibers from wood surface or members fracture near the interface when loading increased. Since the reinforced zones of the joints by FRP show the maximum shear stress, consequently the separation of fibers from wood surfaces increased at these locations. The adhesion of FRP layers to joint surface was not appropriate due to difficult process of layering at right angle of joints followed by probable formation of air bubbles. The results of assessing FRPs reinforcing behaviour indicated that application of vinyl ester in comparison with epoxy as matrix exhibited better performance. In addition, glass and carbon fibers showed better performance than Kevlar fibers as reinforcing agents.
https://ijwpr.areeo.ac.ir/article_102671_b41233dd4ca69d36343e1e1c5aa8e135.pdf
استیله
سیلر و کیلر
نیم پلیاستر
راش
مقاومت چسبندگی
Acetylation
nitrocellulose lacquer
asid catalyzed lacquer and Half Ppolyester
beech
bond resistance
per
موسسه تحقیقات جنگلها و مراتع کشور
تحقیقات علوم چوب و کاغذ ایران
1735-0913
2383-112X
2016-03-20
31
1
118
129
10.22092/ijwpr.2015.105609
105609
Research Paper
عملکرد سازه ای اتصال گوشه مقاوم سازی شده با پلیمرهای تقویت شده با الیاف تحت بارگذاری کشش قطری
Structural Performance of Corner Joint Reinforced with FRP under Diagonal Tension Loading
حمیده عبدل زاده
h_abdolzadeh@ut.ac.ir
1
قنبر ابراهیمی
ibrahimi@ut.ac.ir
2
محمد لایقی
mlayeghi@ut.ac.ir
3
فارغالتحصیل دکترای علوم و صنایع چوب و کاغذ، دانشکده منابع طبیعی، دانشگاه تهران
استاد صنایع چوب و کاغذ، دانشکده منابع طبیعی دانشگاه تهران
استادیار دانشکده منابع طبیعی دانشگاه تهران
در تحقیق حاضر عملکرد سازهای اتصال گوشه مقاومسازی شده با پلیمرهای تقویت شده با الیاف در ناحیه حداکثر تنش کششی (گوشه داخلی) تحت بارگذاری کشش قطری مورد مطالعه قرار گرفت. بدین منظور 1 تا 3 لایه از پارچههای تک جهته الیاف شیشه، کربن و کولار مورد استفاده قرار گرفت و عمل لایهگذاری به صورت دستی و با استفاده از دو نوع رزین وینیلاستر و اپوکسی انجام گرفت. نتایج اندازهگیری نیرو و تغییرمکان در حد تسیلم، نشان دادهاند که لایههای تقویت کننده تا حدی قادر به-جلوگیری از باز شدن اتصال تحت بار هستند. با افزایش بار و با جدا شدن الیاف از سطح چوب و یا شکست اعضا در ناحیهای نزدیک به سطح مشترک، گسیختگی در اتصال مشاهده شده است. همچنین به دلیل اینکه محل تقویت اتصال با پلیمرهای تقویت شده با الیاف دارای حداکثر مقدار تنش برشی است، جداشدن الیاف از سطح چوب افزایش یافتهاست. بهعلت دشواری لایه گذاری با زاویه 90 درجه و احتمال تشکیل حبابهای هوا چسبندگی مناسب کاهش پیدا میکند. نتایج بررسی رفتار تقویت کنندگی پلیمرهای تقویت شده با الیاف نشان دادهاند که ماتریس وینیلاستر در مقایسه با ماتریس اپوکسی و همچنین الیاف شیشه و کربن نسبت به الیاف کولار عملکرد بهتری داشتهاند.
In this study, structural performance of corner joint reinforced by fiber reinforced polymers (FRP) at the area of maximum tension stress was investigated under diagonal tension loading. Therefore 1 to 3 layers of unidirectional woven Glass, Carbon and Kevlar fibers were used and hand lay-up was done by vinyl ester and epoxy resins. Results of load-displacement curve at yield point exhibited capability of the reinforcing layers in preventing joint opening to some extent under load. However, failure was observed at the joint due to picking fibers from wood surface or members fracture near the interface when loading increased. Since the reinforced zones of the joints by FRP show the maximum shear stress, consequently the separation of fibers from wood surfaces increased at these locations. The adhesion of FRP layers to joint surface was not appropriate due to difficult process of layering at right angle of joints followed by probable formation of air bubbles. The results of assessing FRPs reinforcing behaviour indicated that application of vinyl ester in comparison with epoxy as matrix exhibited better performance. In addition, glass and carbon fibers showed better performance than Kevlar fibers as reinforcing agents.
https://ijwpr.areeo.ac.ir/article_105609_4a8c21fad2d8dd489a7cc1ac38068cff.pdf
اتصال گوشه
پلیمرهای تقویت شده با الیاف
رزین وینیل استر و رزین اپوکسی
Corner joint
Fiber reinforced polymer
vinyl ester resin and epoxy resin
per
موسسه تحقیقات جنگلها و مراتع کشور
تحقیقات علوم چوب و کاغذ ایران
1735-0913
2383-112X
2016-03-20
31
1
130
140
10.22092/ijwpr.2015.105612
105612
Research Paper
رفتار زیست تخریب پذیری و مهاجرت در کامپوزیت های پلی لاکتیک اسید تقویت شده با نانوکریستال سلولز و نانورس
Biodegradation and migration behavior of cellulose nanocrystal - nanoclay reinforced PLA composites
بهزاد کرد
b.kord@standard.ac.ir
1
مهدی روحانی
mroohani@standard.ac.ir
2
استادیار گروه سلولزی و بسته بندی، پژوهشکده شیمی و پتروشیمی، پژوهشگاه استاندارد، کرج، صندوق پستی 139-31745، ایران
استادیار گروه سلولزی و بسته بندی، پژوهشکده شیمی و پتروشیمی، پژوهشگاه استاندارد، کرج، صندوق پستی 139-31745، ایران
این تحقیق با هدف بررسی تأثیر حضور همزمان نانوکریستال سلولز و نانورس بر رفتار زیستتخریبپذیری و مهاجرت فیلم های برپایه پلی لاکتیک اسید انجام شد. فیلم های پلی لاکتیک اسید و نانوکامپوزیت های آن حاوی درصدهای مختلف نانوکریستال سلولز و نانورس (0، 3 و 5 درصد وزنی) با استفاده از روش قالب گیری حلال ساخته شد. برای بهبود سازگاری و اختلاط پذیری با پلیمر، نانوکریستال سلولز با اسید اولئیک وارد واکنش شده و اصلاح شد. سپس، برای ارزیابی رفتار زیست تخریب پذیری و مهاجرت فیلم ها، میزان کاهش وزن در آنزیم و دفن در خاک و کمپوست و میزان مهاجرت کلی نمونه ها اندازه گیری شد. نتایج نشان داد که میزان زیست تخریب پذیری کامپوزیت ها در محیط آنزیمی، خاک و کمپوست، با افزایش مقدار نانوذرات کاهش می یابد. از طرف دیگر با افزودن نانوکریستال سلولز و نانورس به ماده زمینه پلیمری میزان مهاجرت کلی کامپوزیت ها کاهش یافت. این مسئله را می توان به چسبندگی بهتر نانوذرات با ماده زمینه پلیمری و تشکیل مسیرهای پرپیچ و خم نسبت داد.
In this study, the synergic effects of cellulose nanocrystal and nanoclay on the biodegradation and migration behavior of composite films based on polylactic acid (PLA) were investigated. PLA and PLA-based nanocomposite films containing different loads of cellulose nanocrystal and nanoclay (0, 3 and 5 wt % each) were fabricated using a solvent casting method. In order to improve the compatibility and miscibility of the whole system with respect to PLA matrix, cellulose nanocrystal was treated with oleic acid. For evaluating the biodegradation and migration behavior of films, the enzymatic degradation, biodegradation, buried in soil and compost; and overall migration were tested. The results indicated that the biodegradability of the composites increased with the increase of nanoparticles in the enzymatic, soil and compost media. Besides, with the addition of cellulose nanocrystal and nanoclay to the polymer matrix, the overall migration of composites decreased. This could be due to a better adhesion of the nanoparticles to the polymer matrix, and the tortuousity of their path.
https://ijwpr.areeo.ac.ir/article_105612_db6f1b239aeffafcfd501723cd10c75a.pdf
نانوکامپوزیت
پلی لاکتیک اسید
زیست تخریب پذیری
کاهش وزن
مهاجرت کلی
nanocomposite
polylactic acid
Biodegradation
WEIGHT LOSS
overall migration
per
موسسه تحقیقات جنگلها و مراتع کشور
تحقیقات علوم چوب و کاغذ ایران
1735-0913
2383-112X
2016-03-20
31
1
141
153
10.22092/ijwpr.2015.105605
105605
Research Paper
اثر تیمار لایه مغزی و مقدار پرکننده پودر بادام در خط چسب بر روی مقاومت چسبندگی کششی پانل ساندویچ
The effect of core layer treatment and almond shell powder content in the glue line on the pull off adhesion sandwich panel
مرتضی ناظریان
morteza17172000@yahoo.com
1
وحید معظمی
moazami_vahid@yahoo.com
2
رحیم محبی گرگری
rahim.mohebbi@yahoo.com
3
دانشیار گروه علوم و صنایع چوب و کاغذ، دانشگاه زابل،
دانشجوی کارشناسی ارشد گروه علوم و صنایع چوب و کاغذ، دانشگاه زابل
مربی گروه علوم و صنایع چوب و کاغذ، دانشگاه زابل
هدف از این پژوهش بررسی اثر تیمار خردههای نی(Arundo donax) بکار رفته در لایه میانی پانل ساندویچی (بدون تیمار، با تیمار حرارتی خشک و آب جوش) و نیز نسبت وزنی پودر پوسته میوه بادام به رزین ملامین اوره فرمآلدئید در سه سطح (3:97، 18:82 و 33:67) بر روی مقاومت چسبندگی کششی خشک و تر (بعد از 2 ساعت غوطهوری در آب جوش) پانل ساندویچی بوده است. تحلیل آماری نتایج و گروهبندی دانکن نشان داد که نوع تیمار خردههای لایه میانی و نسبت پودر پوسته میوه بادام تأثیر معنیداری بر روی مقاومت چسبندگی کششی خشک و تر داشته است. نتایج حاصل از طیفهای FT_IR بهدست آمده از نمونه-های پانلهای ساخته شده با خردههای تحت تیمار آب جوش نیز نشان داد که تیمار آب جوش باعث افزایش تعداد پیوندهای شیمیایی میشود. همچنین تصاویر ماکروسکوپی نشان داده است که تیمار آب جوش بهترین سطح، جهت اتصال مطلوب را می تواند ایجاد کند. بهطور کلی پانلهای حاوی خردههای تیمارشده با آب جوش در لایه مغزی و 33 درصد پرکننده پودر پوسته میوه بادام در خط چسب بیشترین مقاومت چسبندگی کششی در حالت خشک (MPa 01/5) و تر (MPa 86/2) را داشتهاند.
The aim of this study was the evaluation of treatment effect of giant reed (Arundo donax) (untreated, heat-treated and hot-water-leached treatment) used in core layer of sandwich panel, and also the effect of weight ratio of almond shell powder to melamine/urea formaldehyde at three levels (3:97, 18:82 and 33:67 w/w) on the dry- and wet-pull off adhesion (after 2 hours immersion in boiling water) of sandwich panel. Statistical analysis and Duncan multiple range test showed that the type of treatment of core layer particle and the ratio of almond shell powder to melamine/urea formaldehyde statistically influenced the dry and wet-pull off adhesion. According to the FTIR spectra obtained from samples made from particle treated with hot-water, the hot-water treatment caused an increase in number of hydrogen bonds. Macroscopic photos, also, showed that hot-water treatment created the best surface quality in order to forming desirable bond. Generally, panel manufactured from hot-water-treated particles in core layer and 33% of almond shell powder in glue line had the highest pull off adhesion in dry (5.01MPa) and wet (2.86 MPa) conditions.
https://ijwpr.areeo.ac.ir/article_105605_ca6d80e20f8bccf37a69911b14695735.pdf
پانل ساندویچ
پوسته میوه بادام
طیف مادون قرمز
پودر
مقاومت چسبندگی کششی
sandwich panel
almond shell powder
FTIR
pull off adhesion
per
موسسه تحقیقات جنگلها و مراتع کشور
تحقیقات علوم چوب و کاغذ ایران
1735-0913
2383-112X
2016-03-20
31
1
154
165
10.22092/ijwpr.2015.102673
102673
Research Paper
اثر طول ذرات میکرو سلولز بر خواص مکانیکی ، حرارتی و مورفولوژیکی نانو چندسازه چوب- پلاستیک
The Effect of Micro-Cellulose Length on Mechanical, Thermal and Morphological Properties in Nano/Wood Plastics Composites
امیر نوربخش
nourbakhsh_amir@yahoo.com
1
ابوالفضل کارگرفرد
a_kargarfard@yahoo.com
2
دانشیار، صنایع چوب و کاغذ، بخش تحقیقات علوم چوب و فراوردههای آن، مؤسسه تحقیقات جنگلها و مراتع کشور، تهران
دانشیار، صنایع چوب و کاغذ، بخش تحقیقات علوم چوب و فراوردههای آن، مؤسسه تحقیقات جنگلها و مراتع کشور، تهران
در این بررسی استفاده از ذرات میکروکریستالین سلولز در ساخت نانو چندسازه چوب پلاستیک مورد توجه قرار گرفته است. اثرات ابعاد ذرات میکرو کریستالین سلولز و جفت کننده مالییکی(MAPP) بر خواص مکانیکی، ریخت شناسی و حرارتی نانو چندسازه چوب پلاستیک مطالعه شده است. در این بررسی استفاده از ذرات میکروکریستالین سلولز بهمراه آرد چوب در دو سطح 20 و 50 میکرون ، درصد جفت کننده مالییکی 5/2 و 5 درصد بهمراه 3 درصد نانو رس در تهیه چند سازه چوب پلاستیک مورد توجه قرار گرفت. نتایج خواص مکانیکی در چندسازه با طول 50 میکرون ذرات میکرو سلولز و 5 درصد جفت کننده نسبت به سایر تیمارها برتر بوده است. همچنین نتایج آزمایشات نشان دادکه استفاده از جفت کننده مالییکی باعث بهبود خواص حرارتی در جریان مخلوطسازی در فاز درون سطحی شده و سبب اتصال بهتر بین الیاف و ماتریس گردیده است. خواص مکانیکی نانو چند سازه با استفاده از عکسبرداری SEM و TEM مورد بررسی گرفته است. پراکنش ذرات نانو رس در ماتریس چند سازه و تجزیه و تحلیل رفتار حرارتی چند سازه نیز به کمک آزمون TGA نشان داده که استفاده از 5% عامل جفت کننده مالییکی بهمراه ابعاد بلندتر ذرات میکرو سلولز بطور مشخص باعث افزایش مقاومت حرارتی چند سازه نسبت به سایر تیمارها شده است.
In this research the impact of micro cellulose particles length, and coupling agent (MAPP) on the mechanical and thermal properties of Nano/ wood plastics composites were investigated. The results showed that mechanical properties of the composites made with 50 micron micro cellulose particles and 5 % of MAPP were significantly different to those of the lower length (20 micron) and 2.5% of MAPP. Addition of MAPP enhanced the mechanical and thermal properties of the blends, due to the improvement of interface bond between the filler and matrix of Nano/ wood plastics composites. The significant improvements in mechanical properties of the blended composites made with MAPP and NC were further supported by SEM and TEM micrographs. Nano/ clay particles distribution and thermo gravimetric analysis (TGA) indicated that the addition of 5% MAPP and the longer micro cellulose particles remarkably increased the thermal stability of the blends compared to other treatments of Nano/ wood plastics composites.
https://ijwpr.areeo.ac.ir/article_102673_3c70327d5480a38edf15d15dd6b5b538.pdf
چندسازه
میکرو سلولز
نانو رس
جفتکننده مالییکی
خواص مکانیکی
خواص حرارتی
Composite
MECHANICAL PROPERTIES
Micro- cellulose
Thermal properties
Nanoclay
per
موسسه تحقیقات جنگلها و مراتع کشور
تحقیقات علوم چوب و کاغذ ایران
1735-0913
2383-112X
2016-03-20
31
1
166
179
10.22092/ijwpr.2015.105611
105611
Research Paper
کاربرد نانو نقره در تولید کاغذ اسکناس ضد باکتری
Application of nano silver in the production of antibacterial banknote paper
امید یزدانی آقمشهدی
omidyazdani29@yahoo.com
1
قاسم اسد پور اتویی
gh.asadpour@sanru.ac.ir
2
اسماعیل رسولی گرمارودی
e_rasooly@sbu.ac.ir
3
رضا ایمانی
rezaim56@yahoo.com
4
دانشآموخته کارشناسی ارشد صنایع خمیر و کاغذ، دانشگاه علوم کشاورزی و منابع طبیعی ساری
استادیار، گروه مهندسی چوب و کاغذ، دانشگاه علوم کشاورزی و منابع طبیعی ساری
استادیار، گروه مهندسی فناوری تولید سلولز و کاغذ، دانشگاه شهید بهشتی، زیرآب، سوادکوه
دانش آموخته مقطع دکتری دانشگاه آزاد اسلامی واحد علوم تحقیقات تهران
اسکناس درطی دوره عمر خود از محیط های مختلف و مشاغل گوناگون، آن هم با فراوانی زیاد عبور می کند به طوریکه طی مطالعات علمی ثابت شده، اسکناس کاغذی را می توان یکی از مهمترین و شاید کم نظیرترین عوامل انتقال دهنده بیماری های عفونی و انگلی در جامعه دانست. هدف از این تحقیق بررسی راهکار مناسبی جهت ضد باکتری کردن کاغذ اسکناس با استفاده از نانو ذرات نقره به عنوان ماده ضد باکتری و کمک نگهدارنده پلی اکریل آمید کاتیونی می باشد. برای این کار خمیرکاغذ آزمایشگاهی الیاف پنبه رنگبری شده با پروکسید با درجه روانی oSR34 و درصد خشکی % 1/3 و pH خنثی تهیه و سپس مواد افزودنی فوق با شرایط مشخص (نانو نقره با مقادیر مصرف 25، 50، 75 و100 پی پی ام به همراه میزان 3/0 درصد پلی اکریل آمید کاتیونی) به آن اضافه گردیده و در پایان از آنها کاغذهای دست ساز 90 گرمی ساخته شد. جهت بررسی صحت نشست ذرات نقره از کاغذهای فوق تصاویر میکروسکوپ الکترونی تهیه شد. به منظور بررسی ضدباکتری شدن کاغذ از روش طیف سنجی فرابنفش-مرئی UV-vis استفاده گردید. همینطور کاغذها از نظر ویژگی های نوری و مقاومتی مورد ارزیابی قرار گرفتند. نتایج نشان داد با افزایش میزان مصرف نانو نقره، میزان مقاومت های کاغذ روند کاهشی، ماتی افزایش و از روشنی کاسته شده است. در خصوص آزمون بیولوژیکی نتایج نشان داد با مصرف بیشتر نانو نقره خصوصیات ضد باکتری کاغذ افزایش یافته است. بنابراین، با توجه به نتایج آزمونهای مقاومتی، نوری و بیولوژیکی و نیز در نظر گرفتن جنبه های اقتصادی و زیست محیطی، میزان مصرفppm 25 برای نانونقره به عنوان تیمار بهینه تعیین گردید.
Bank-note during in its lifetime exposed to different environments and various applicationns with high frequency. As it is confirmed in scientific studies, bank-note can be one of the most important and perhaps rarest of disease and parasites carriers in society. The goal of this study is evaluation of the appropriate solution for antibacterial banknote paper production using silver nanoparticles as an antibacterial agent and a cationic polyacrylamide as retention aid. Laboratory pulp of cotton fibers bleached with hydrogen peroxide with freeness of 34 °SR, consistency of 3.1% and neutral pH were prepared and then above additives were added with specified conditions (nano silver with 25, 50, 75 and 100 ppm with 0.3% percent cationic polyacrylamide) and finally 90 g/m2 standard handsheets made from above mentioned pulp. To verify the presence of silver particles in paper structure, the hand sheet papers were characterized by SEM. UV-vis spectrophotometric method was used to evaluate of antibacterial properties of paper. Also, papers were analyzed in strength and optical properties. The results showed that with increasing the silver nanoparticles consumption, paper strength properties and brightness were decreased, and opacity increased. The biological test results showed that the antibacterial properties of paper were improved with silver nanoparticles consumption. Based on the results of strength, optical and biological tests and also economic and environmental overviews, 25ppm consumption of nano-silver was determined as optimized treatment.
https://ijwpr.areeo.ac.ir/article_105611_e648a2bac6281b91d1a5b5547da87b38.pdf
کاغذ اسکناس
کدورت سنجی
کاغذ ضد باکتری
نانوذرات نقره
Bank-note
turbidity test
paper antibacterial
Silver nanoparticles