Majid Salehi; Mohammad Talaei poor; Habibollah Khademi Eslam; Behzad Bazyar
Abstract
The use of various pretreatments, including the torrefaction process, in order to increase the efficiency and optimize the consumption of fuel briquettes, have attracted a lot of attention in recent years. Therefore, in this research, torrefaction pretreatment at 180 ºC temperature was used to modify ...
Read More
The use of various pretreatments, including the torrefaction process, in order to increase the efficiency and optimize the consumption of fuel briquettes, have attracted a lot of attention in recent years. Therefore, in this research, torrefaction pretreatment at 180 ºC temperature was used to modify bagasse biomass. In addition, lignin binding agent was used at levels of 2, 5 and 10%. Fuel briquettes weighing 30 grams were prepared using a manual briquetting machine. The physical, resistance and thermal characteristics of the resulting briquettes were investigated. The results showed that torrefaction pre-treatment by increasing the volumetric density of the resulting briquettes and increasing the amount of fixed carbon up to about 50% was able to increase the heating value of the briquettes up to about 10%, on the other hand, this process led to a decrease in the compressive strength of the resulting briquettes, which is used lignin as a binding agent could compensate a significant amount of this resistance drop. The results showed that the number of volatile substances of briquettes was reduced by 9% with torrefaction pre-treatment, which has a significant effect on reducing the pollution of these briquettes. In the study of the effect of lignin, it was also observed that with the increase in the consumption of lignin, the density and calorific value also increased. In general, the results of this research show that the use of lignin binding agent together with torrefaction pre-treatment can make possible the production of high-quality fuel briquettes from bagasse.
Mohammad Reza topa esfandiyari; Mohammad Talaei poor; Habibollah Khademi Eslam; Seeyed Ahmad Mirshokraie; behzad baziyar
Abstract
This study uses soda lignin to modify it with furfural as adhesive on the physical and mechanical properties of plywood Poplar wood. Producing plywood, pure Lignin (L.100%), lignin-furfural 30% (L.70-F.30), lignin- furfural 60% (L.40-F.60) were used as the adhesive at three different levels ( 120 140 ...
Read More
This study uses soda lignin to modify it with furfural as adhesive on the physical and mechanical properties of plywood Poplar wood. Producing plywood, pure Lignin (L.100%), lignin-furfural 30% (L.70-F.30), lignin- furfural 60% (L.40-F.60) were used as the adhesive at three different levels ( 120 140 160gm2) accompanied with ammonium chloride (1%) as the hardener and wheat flour (30%) as the filler based on the dry weight of the adhesive. Plates made with urea formaldehyde resin at 160 g/m2 were produced as control samples. characteristics of adhesives included solid material percentage, viscosity, specific weight and PH were measured. After producing the laboratory boards, the physical and mechanical properties of samples, such as thickness swelling after 2 and 24 hours of being soaked in water, shear strength, modulus of rupture, and modulus of elasticity were measured. The results indicate that independent and interactive effects of adhesive and its consumption level on the physical and mechanical properties of plywood are not statistically significant. And in all cases, the control boards had better properties than the lignin adhesives
Yashar Einollahi; Amir Hooman Hemmasi; Habibollah Khademi Eslam; Esmaeil Ghasemi; Mohammad Talaei poor
Abstract
Considering the increase of environmental pollutant resulted from agglomerating rubbish and wastes containing stable petroleum-based polymers, substitution of these polymers with bio-polymers and solving their problems and defects in the production process as well as the final products is an important ...
Read More
Considering the increase of environmental pollutant resulted from agglomerating rubbish and wastes containing stable petroleum-based polymers, substitution of these polymers with bio-polymers and solving their problems and defects in the production process as well as the final products is an important topic. In this study, the possibility of the production of poly lactic acid (PLA)-rice husk composite with acceptable properties, and also the effect of using flame retardant mineral fillers of aluminum three hydrates (ATH) and magnesium di-hydroxide (MDH) on physical and thermal properties of the produced composite were investigated. Results indicated that the density of PLA-rice husk composite was higher than petroleum-based polymers composites (PP/HDPE-rice husk composites); and flame retardant mineral fillers addition led to an increase in the composite density. Also, flame retardant mineral fillers addition decreased the composite water absorption and thickness swelling, in a way that they were comparable with petroleum-based polymers composites. Results of thermal gravimetric analysis (TGA) showed that flame retardant mineral fillers addition also decreased the temperature of the composite weight loss curve peaks, and the weight loss rate toward temperature rising.
Ali Kazemi Tabrizi; Habibollah Khademi Eslam; Amir Hooman Hemmasi; Behzad Bazyar; Vahid Atghia
Abstract
Abstract In this study, acidified Luffa (AHS@L), by sulfonic acid, as an effective and biodegradable solid acid catalyst was produced. The synthesized catalyst was characterized by TGA, SEM, XRD and FTIR, and the results indicated that modified Luffa flour had an intense acidic property. The FT-IR analyze ...
Read More
Abstract In this study, acidified Luffa (AHS@L), by sulfonic acid, as an effective and biodegradable solid acid catalyst was produced. The synthesized catalyst was characterized by TGA, SEM, XRD and FTIR, and the results indicated that modified Luffa flour had an intense acidic property. The FT-IR analyze show a broad peak at 3400cm-1 that improve the acidification of the Luffa surface. Also the XRD analyze clearly show the change in the morphology of Luffa after acidification. The TGA analyze show us the heat resistance of the catalyst up to 245 ° C and the SEM images clearly showed that the catalyst surface was hydrated as a result of acidification. The synthesized catalyst was used to protect the amines in the N-tert butyl carbamate reaction under solvent-free conditions at room temperature. Different types of aliphatic and aromatic amines have been produced as related monocarbamates with excellent yields and short reaction times. This method was mild and selective and has advantages such as heterogeneous catalysis, low cost and catalyst recovery capability.
mona shayestehkia; Habibollah Khademi Eslam; Behzad Baziyar; Hossein Rangavar; Hamid Reza Taghiyari
Abstract
Abstract In this research, the effect of cellulose nanocrystals on the functional properties of wood cement composite panels has been investigated. Variable factors in this research are the percentage of nano in (five levels of 0, 0.1, 0.2, 0.5 and 1%), the weight of cement and also the ratio of mixing ...
Read More
Abstract In this research, the effect of cellulose nanocrystals on the functional properties of wood cement composite panels has been investigated. Variable factors in this research are the percentage of nano in (five levels of 0, 0.1, 0.2, 0.5 and 1%), the weight of cement and also the ratio of mixing wood chips with cement in three levels (1 to 3, 1 To 3.5 and 1 to 4) dry weight of cement. In this research, poplar wood and Portland cement type 2 have been used as fixed agents. In total, 15 treatments and 3 replicates of each treatment were made. Preparation of sample in accordance with the standard (DIN / EN 634) and measurement of physical and mechanical properties including flexural modulus, modulus of elasticity in accordance with the standard (DIN / EN 310), internal adhesion in accordance with the standard (DIN / EN 319), thickness swelling after 2 and 24 hours of immersion in water was performed according to the standard (DIN / EN 317). Increased cellulose nanocrystals improved physical and mechanical strength. SEM microscopic images were taken from the samples to examine the microstructural properties of the composite. In the pictures, it was found that by adding cellulose nanocrystals, we see an improvement in the disintegration of nanocomposite materials and as a result, an increase in mechanical and physical properties
Mohammad Reza topa esfandiyari; Mohammad Talaei poor; Habibollah Khademi Eslam; Seeyed Ahmad Mirshokraie; Behzad Bazyar
Abstract
This study uses the Lignin-Glyoxal adhesive to replace chemical resins with environmental compounds producing plywood. producing plywood, pure Lignin (L.100%), lignin- glyoxal 15% (L.85-G.15), lignin-glyoxal 30% (L.70-G.30) and Urea-formaldehyde (control) were used as adhesive at 160 gr/m2 level. Accompanied ...
Read More
This study uses the Lignin-Glyoxal adhesive to replace chemical resins with environmental compounds producing plywood. producing plywood, pure Lignin (L.100%), lignin- glyoxal 15% (L.85-G.15), lignin-glyoxal 30% (L.70-G.30) and Urea-formaldehyde (control) were used as adhesive at 160 gr/m2 level. Accompanied with ammonium chloride (1%) as the hardener and wheat flour (30%) as the filler based on the dry weight of the adhesive characteristics of adhesives included solid material percentage, viscosity, specific weight and PH were measured. After producing the laboratory boards, the physical and mechanical properties of samples, such as thickness swelling after 2 and 24 hours of being soaked in water, shear strength, modulus of rupture, and modulus of elasticity were measured. In addition, the groups and bonds in the pure lignin and lignin-gloxal adhesives were identified by Fourier Transform Infrared (FTIR) spectroscopy. The results indicated that the independent effect of adhesive type on the thickness swelling of plywood after 2 and 24 hours was significant. Although the results suggest that modifying the lignin would improve the plywood in all cases, the control boards had better featurers than those made with the Lignin-Glyoxal adhesive.
Ai Hasanpoor tichi; Fardad Golbabaei; Habibollah Khademi Eslam
Abstract
In this study, the effect of nano-wollastonite on physical, mechanical and morphological properties of composites made of bagasse and gypsum was investigated. The mixing ratio of sugarcane to gypsum pulp at three levels (80:20, 70: 30 and 40: 60%) and nano-wollastonite at three levels of zero, 3 and ...
Read More
In this study, the effect of nano-wollastonite on physical, mechanical and morphological properties of composites made of bagasse and gypsum was investigated. The mixing ratio of sugarcane to gypsum pulp at three levels (80:20, 70: 30 and 40: 60%) and nano-wollastonite at three levels of zero, 3 and 7% were considered as the variables of this study. The thickness of the test boards was 16 mm cake density of all boards was considered to be 1.10 gr/cm3. Then the mechanical and physical properties of the specimens including modulus of rupture, modulus of elasticity, internal bonding, water absorption after 2 and 24 hours immersion and density of boards according to DIN-EN-634 and fire resistance (weight loss percentage) according to ISO 11925 Were measured. In this study, a thermocouple and a flask were used to measure the hydration heat. Microscopic images (SEM) were obtained from the fracture surface of the specimens to investigate the common boundary between bagasse-gypsum and nano-dispersion. The results showed that with increasing bagasse mixing, the modulus of rupture, modulus of elasticity and internal bonding decreased and water absorption and weight loss percentage of boards exposed to fire increased. Application of nano-wollastonite up to 7% improved all mechanical and physical properties of composites. Also, microscopic imaging (SEM) showed that the optimum level of nano-wollastonite can fill vacant voids due to gypsum hydration and create a uniform structure.
Amir Mollahassani; Amir Hooman Hemmasi; Habibollah Khademi Eslam; Amir Lashgari; behzad baziyar
Abstract
The aim of this study is to evaluate the dynamic and static of elastic properties of Fir wood joints. For this purpose conventional joints in woos industry including dovetail, tongue and groove beech wood (Abies alba.) joints with polyvinyl acetate (PVA) and cyanoacrylate (CA) adhesives were used. Dimensions ...
Read More
The aim of this study is to evaluate the dynamic and static of elastic properties of Fir wood joints. For this purpose conventional joints in woos industry including dovetail, tongue and groove beech wood (Abies alba.) joints with polyvinyl acetate (PVA) and cyanoacrylate (CA) adhesives were used. Dimensions of research samples were determined 24×50×360 (mm) according to international standard (ISO No.3129), and the results indicate that the effects of joint type, adhesive type, joint size, and also retrospective joint size became meaningful at 5% level in dynamic and static tests. As the length of groove and height of dovetail and length of dowel increased in the joints, dynamic and static elasticity modules increased, and in terms of changes in elasticity modules of the research. Elasticity module for dovetail joint, as a result of the shape, having a homogenous joint texture, and also lack of extended adhesive line in the joint, is closer to un jointed samples (control group). Also cyanoacrylate adhesive improved elasticity features of samples compared to polyvinyl acetate adhesive as a result of higher tension resistance and faster coagulation. The results of the Student's t-test indicate that there exists a not significant difference between the mean of dynamic and the mean of static modulus of elasticity, not significance at 5% level and The Pearson correlation test indicate that the dynamic and static modulus of elasticity of the samples are significant at 5% level and are of positive correlation(+.0958) .With regard to the correlation of the results of dynamic and static tests, methods for non-destructive dynamic investigation may be regarded as appropriate alternatives to destructive static tests, in order to assess and classify woods.
Composite wood products
Salume Esmaeilzadeh Saeih; Habibollah Khademi Eslam; Esmaeil Ghasemi; behzad baziyar
Abstract
Abstract Effects of temperature, cellulose Nano fibers and Nano clay particles on mechanical, physical and morphological properties of biodegradable composites made of recycled thermoplastic starch biopolymer and regular mixed industrial sawdust are investigated. To this aim Cellulose Nano Fibers and ...
Read More
Abstract Effects of temperature, cellulose Nano fibers and Nano clay particles on mechanical, physical and morphological properties of biodegradable composites made of recycled thermoplastic starch biopolymer and regular mixed industrial sawdust are investigated. To this aim Cellulose Nano Fibers and Nano Clay particles were selected to be 0, 3 and 5 weight percent and were added to prepared biodegradable composites by using internal mixer and samples prepared by injection molding. Mechanical properties including tensile modulus and strength, flexural modulus and strength were extracted at temperatures ranging from 23 ºC to 80 ºC. Impact test and water absorption and thickness swelling were also performed according to related standards. Results show that elevating the temperature drastically reduce mechanical properties. Nano Clay addition results in better mechanical properties except for impact and water absorption and thickness swelling are improved. Using 5% Cellulose Nano Fibers improves mechanical and morphological properties better than 3% addition. Dynamic mechanical thermal analysis revealed Nano composites samples with 5% Nano Clay and Cellulose Nano Fibers has higher storage modulus and glass transition temperatures in compare to pure composite samples. This Nano particles can be successfully used to improve properties and performance except for fracture resistance.
Composite wood products
Abbas Tamjidi; Mohamad Mehdi Faezipour; Habibollah Khademi Eslam; Ghanbar Ebrahimi; Kazem DoosthoseinI
Abstract
DOR:98.1000/1735-0913.1398.34.140.66.1.9.1586 In this study, the possibility of three-layered oriented strand board production from hornbeam (Carpinus betulus L.) wood was evaluated. Two levels of press time (6 and 8 minutes) and three levels of press temperature (180˚C, 200˚C and 220˚C) were applied ...
Read More
DOR:98.1000/1735-0913.1398.34.140.66.1.9.1586 In this study, the possibility of three-layered oriented strand board production from hornbeam (Carpinus betulus L.) wood was evaluated. Two levels of press time (6 and 8 minutes) and three levels of press temperature (180˚C, 200˚C and 220˚C) were applied and 12 mm thick laboratory boards were made from hornbeam wood. The strands on the surface layers were aligned in the long direction of the board and the middle layer strands are cross aligned to the surface layers. In all treatments, board targeted density of 0/7 g/cm3 and mat moisture content of 7% and phenol-formaldehyde resin (PF) content of 7% based on the oven dry weight of the strands were kept constant. The mechanical and physical properties of the boards were measured as defined in relevant European standards test methods EN 300. The internal bound (IB) and thickness swelling (TS24) of boards were significantly improved as the press time increased from 6 to 8 minutes. The modulus of rupture (MOR) and internal bound (IB) and thickness swelling (TS24) were significantly improved as the press temperature increased from 180˚C to 220˚C. Overall results showed that the highest MOR and IB and the lowest TS24 were achieved at 8 minutes press time and 220˚C press temperature and all boards made from this mentioned conditions exceed the EN 300 standards for MOR, MOE, IB and TS24.
Management and Economics wood
Afshin Kshn dehghan; Habibalah Khademi eslam; Behzad Bazyar
Abstract
In this study, the influence of the fungus (Coriolus versicolor) on the durability of Horn beam (carpinus betulus) in natural state and treated with CCA (Copper/Chromium/Arsenic) was evaluated. CCA is a kind of water borne preservatives that was used to treat specimens under vacuum and pressure ...
Read More
In this study, the influence of the fungus (Coriolus versicolor) on the durability of Horn beam (carpinus betulus) in natural state and treated with CCA (Copper/Chromium/Arsenic) was evaluated. CCA is a kind of water borne preservatives that was used to treat specimens under vacuum and pressure (Bethel procedure) with amount of 3.5 & 1.5 percent on the basis of oven dry wood. Specimens were contaminated with cultured fungus for eight weeks in incubator. After this period, weight reduction, compressive strength (parallel to grain) and hardness of specimens were measured. Weight reduction of treated samples with 3.5 & 1.5 percent CCA were 1.68 and 1.73 percent respectively. Weight reduction of control samples were much higher (22.87 percent) than treated ones. There was no significant difference between the Compressive strength (parallel to grain) of treated and control samples without effect of fungus but the samples with effect of fungus have significant difference. Compressive strength (parallel to grain) of treated samples with 3.5 & 1.5 percent of CCA were 64.33 and 60.10 (Mpa) respectively but Compressive strength (parallel to grain) of control samples were much lower (38.44 Mpa) than treated samples. There was no significant difference between the hardness of treated and control samples without effect of fungus. On the other hand, the hardness of treated samples was more than control samples slightly, but this difference was not significant in 5 percent level. The hardness of treated and control samples with effect of fungus have significant difference. Hardness of treated samples with 3.5 & 1.5 percent of CCA were 5788(N) and 5799(N) respectively. However the hardness of control samples were much lower (3139N) than treated samples. Eventually CCA (Tanalith c) increased the durability of Horn beam (Carpinus betulus) from nondurable level to durable level.
Composite wood products
Ahmad Samariha; Habibollah Khademi Eslam
Abstract
Abstract The effect of adding steamed and non-steamed fiber on physical and mechanical properties of the composites made of recycled polypropylene was investigated. Recycled polypropylene was used as a basic matrix at a 57% level, and poplar fibers were used at 180 °C for 1 h at a constant level ...
Read More
Abstract The effect of adding steamed and non-steamed fiber on physical and mechanical properties of the composites made of recycled polypropylene was investigated. Recycled polypropylene was used as a basic matrix at a 57% level, and poplar fibers were used at 180 °C for 1 h at a constant level of 40% in two forms: non-steamed and steamed. The ratio of steamed fibers to non-steamed fibers in composites was 100:0, 50:50, and 0:100, respectively. For all components, the coupling agent was maleic anhydride at a level of 3%. Mixing was done using an internal mixer at 180 °C and 60 rpm, and the samples were constructed by injection molding method. To investigate the effect of steam treatment on the fiber structure and crystallization, X-ray diffraction analysis and FTIR spectra were used. The results showed that the Steaming had no significant effect on resistance. But with steaming increased mechanical properties and physical properties of reduced. Keywords: Composites, Recycled polypropylene, Steamed fiber, XRD, FTIR
Composite wood products
Abbas Tamjidi; Mohammad Mehdi Faezipour; Kazem Doosthoseini; Ghanbar Ebrahimi; Habibollah Khademieslam
Abstract
In this study, the effects of mat moisture content and press temperature on physical and mechanical properties of three layered oriented strand boards were evaluated. Two levels of mat moisture content 7% and 10% and three levels of press temperature 180 ˚c , 200 ˚c and 220 ˚c were applied and 12 ...
Read More
In this study, the effects of mat moisture content and press temperature on physical and mechanical properties of three layered oriented strand boards were evaluated. Two levels of mat moisture content 7% and 10% and three levels of press temperature 180 ˚c , 200 ˚c and 220 ˚c were applied and 12 mm in nominal thickness laboratory boards were made from mixture of three clones of ten-year-old hybrid poplar ( populous euramericana vernirubensis, p. e. I-214, P. e. 561/41) while the strands on the surface layers are aligned in the long direction of the board and the middle layer strands are cross aligned to the surface layers. In all treatments, board targeted density of 0/7 g/cm3 and press time of 8 min and phenol-formaldehyde resin (PF) content of 7% based on the oven dry weight of the strands were held constant. The mechanical and physical properties of the boards were measured as defined in relevant European standards EN 300 for OSB/1 and OSB/2. Overall results showed that all boards made from above mentioned conditions exceed the EN 300 standards for MOR, MOE, IB and TS24. The bending properties (MOR and MOE) of boards were significantly improved as the mat moisture content increased from 7 to 10%. The highest MOR was achieved at 10% mat moisture content and 220 ˚c press temperature and the highest MOE was achieved at 10% mat moisture content and 180 ˚c press temperature. The Modulus of Rupture (MOR) and Thickness swelling (TS24) were significantly improved as the press temperature increased from 180 ˚c to 220 ˚c. The lowest TS24 was achieved at 7% mat moisture content and 220 ˚c press temperature and the highest IB was achieved at 7% mat moisture content and 200 ˚c press temperature.
Composite wood products
Habib alah Khademieslam; Mehdei Kalagar
Abstract
In this investigation, tensile and physical properties of polypropylene (as matrix)/wheat straw fiber/paper mill sludge (as filler) composites was studied. The ratio of wheat straw fiber/ paper mill sludge was selected as 40/0, 30/10, 20/20, 10/30 and 0/40 (w/w) were used. Also, for better ...
Read More
In this investigation, tensile and physical properties of polypropylene (as matrix)/wheat straw fiber/paper mill sludge (as filler) composites was studied. The ratio of wheat straw fiber/ paper mill sludge was selected as 40/0, 30/10, 20/20, 10/30 and 0/40 (w/w) were used. Also, for better compatibility between the two phases 3% MAPP as coupling agent was used. Mixing process was done in twin screw internal mixer extruder, and then composite samples were manufactured by injection molding. Result indicated that the tensile modulus of elasticity improved with increasing fillers and also it was observed that the toughness of composite increased when compared to the pure PP, while due to the usage of more paper sludge, these properties was improved. Tensile strength of composite decreased with adding 40% wheat straw fiber, but with addition of sludge tensile strength increased significantly. Adding wheat straw in PP matrix and its hydrophilic properties resulted in the highest rates of water absorption and thickness swelling. However, adding paper sludge and lower amount of lignocellulosic material, and the compatibilizer noticeably decreased the physical properties due to better bonding between two phases.
Composite wood products
Hassan Ziaei Tabari; Habibollah Khademieslam; Behzad Bazyar; Amir Homan Hemmasi
Abstract
A new kind of thermoplastic elastomer nano composite reinforced with nano cellulose fibers is reported. The first aim of this investigation was to study the interaction and dispersion of nano cellulose fiber into Pebax matrix. This copolymer is Polyether – b – Amide thermoplastic elastomer ...
Read More
A new kind of thermoplastic elastomer nano composite reinforced with nano cellulose fibers is reported. The first aim of this investigation was to study the interaction and dispersion of nano cellulose fiber into Pebax matrix. This copolymer is Polyether – b – Amide thermoplastic elastomer which is synthetized from renewable resources, and its hydrophilic character allows it to interact with nano cellulose. The interaction and reinforcement effect of nano cellulose at 3 levels of nano cellulose (1%, 3% and 5%) were examined by Scanning electron microscopes (SEM), Fourier transform infrared spectroscopy (FTIR) and Mechanical tests (young module, elongation at break and impact resistance). The results achieved from these tests were indicating appropriate effects of nano cellulose fibers for the strong interaction and close contact with polyamide phase of Pebax polymer which caused high mechanical properties (at 3% of nanoellulose) in nano composites. The young module and impact resistance of nano composite were significantly increased.
Management and Economics wood
shahram tahmasebi; behzad bazyar; habibolah Khademi Islam; mohammad Ghofrani
Abstract
In this study, structural performance of corner joint reinforced by fiber reinforced polymers (FRP) at the area of maximum tension stress was investigated under diagonal tension loading. Therefore 1 to 3 layers of unidirectional woven Glass, Carbon and Kevlar fibers were used ...
Read More
In this study, structural performance of corner joint reinforced by fiber reinforced polymers (FRP) at the area of maximum tension stress was investigated under diagonal tension loading. Therefore 1 to 3 layers of unidirectional woven Glass, Carbon and Kevlar fibers were used and hand lay-up was done by vinyl ester and epoxy resins. Results of load-displacement curve at yield point exhibited capability of the reinforcing layers in preventing joint opening to some extent under load. However, failure was observed at the joint due to picking fibers from wood surface or members fracture near the interface when loading increased. Since the reinforced zones of the joints by FRP show the maximum shear stress, consequently the separation of fibers from wood surfaces increased at these locations. The adhesion of FRP layers to joint surface was not appropriate due to difficult process of layering at right angle of joints followed by probable formation of air bubbles. The results of assessing FRPs reinforcing behaviour indicated that application of vinyl ester in comparison with epoxy as matrix exhibited better performance. In addition, glass and carbon fibers showed better performance than Kevlar fibers as reinforcing agents.
Composite wood products
ali hasanpoor tichi; behzad bazyar; Habibalah khademieslam; Mohammad Talaeipoor
Abstract
In this study the possibility of nano- wollastonite usage in three level (0 , 3 and 6 percent per dry weight of cement) and mixture ratios of lingo cellulosic materials to cement in three level 10:90, 20:80 and 30:70 on physical, mechanical and microscopic properties of composite made from kraft fibers ...
Read More
In this study the possibility of nano- wollastonite usage in three level (0 , 3 and 6 percent per dry weight of cement) and mixture ratios of lingo cellulosic materials to cement in three level 10:90, 20:80 and 30:70 on physical, mechanical and microscopic properties of composite made from kraft fibers was investigated. There were three replicatesfor each treatment and 27 experimental boards were manufactured totally. Specimens were prepared according to DIN- EN- 634 standard to measure mechanical and physical properties. Mechanical and physical properties including compression strength, interior bonding (IB), thickness swelling after 2 and 24 hours immersion into the water and density were measured. Micro- structural properties of composites were evaluated by SEM images.The results showed that compression strength , interior bonding and density increased by higher levels of nano- wollastonite content in the boards. By increasing of nano- wollastonite, dimensional stability was significantly improved in comparison to the control boards. SEM images showed the improvement of micro- structural boards by increasing the nano- wollastonite content.
Composite wood products
Mehdi Kalagar; behzad baziyar; Habibalah Khademislam; Esmaeil Ghasemi; Amir homan Hemmasi
Abstract
In this paper, poly lactic acid (PLA)/ wheat straw fibers manufactured by twin screw extruder and molding compression have been studied. Wheat straw fibers were treated with trietoxymethel silane for better compatibility between two phases. Physical properties, tensile properties of the composites were ...
Read More
In this paper, poly lactic acid (PLA)/ wheat straw fibers manufactured by twin screw extruder and molding compression have been studied. Wheat straw fibers were treated with trietoxymethel silane for better compatibility between two phases. Physical properties, tensile properties of the composites were analysis. The effect of the wheat straw fibers on the thermal properties of PLA has also been investigated in DSC experiments. The effects of silane treatment on the wheat straw fibers have been analyzed by FTIR. Scanning electron microscopy from samples surface were used for better study of water absorption and thickness swelling. Composites wheat straw fiber were treated shows signification lower water absorption and thickness swelling than composites PLA/ untreated wheat straw fibers. The lower amount of water absorption and thickness swelling occurred in the pure PLA. The existence crack and break occurred in the surface of PLA/ untreated wheat straw fibers composites after immersion in the water indicating higher water absorption and thickness swelling were in these samples. Wheat straw fibers were treated with silane due to better wetting and better linkage in the interfacial surface with PLA matrix showed higher tensile properties then PLA/ untreated wheat straw fiber composites. Differential scanning calorimeter test showed that with addition wheat straw fibers were treated to pure PLA the increased glass transition temperatures. The nucleating effect of wheat straw fibers, special treatment with silane cause to increased in the crystallization temperature composites than pure PLA which a positive effect showed on the degree of crystallization.
Habib alah Khademi eslam; Zahra Yoosefnia; Esmaeil Ghasemi; Mohammad Talaeipoor
Abstract
The effect of nanoclay and coupling agent contents on the mechanical properties of wood flour/ polypropylene/ nanoclay composites was investigated. Wood flour content was constant at 40%, maleic anhydride at two levels of 2 and 4% and nanoclay (Cloisite 30B) at four levels of 0, 1, 3 and 5% were used. ...
Read More
The effect of nanoclay and coupling agent contents on the mechanical properties of wood flour/ polypropylene/ nanoclay composites was investigated. Wood flour content was constant at 40%, maleic anhydride at two levels of 2 and 4% and nanoclay (Cloisite 30B) at four levels of 0, 1, 3 and 5% were used. The materials were mixed in an internal mixer at 180 o C, 60 rpm for 12 minutes, and then the specimens were fabricated by injection molding method. The mechanical properties such as tensile and flexural strength, flexural modulus and impact strength were measured. The nanoclay dispersion was examined by X-ray diffraction. The results indicated that the tensile and flexural strength, and the flexural modulus increased with increasing the nanoclay, but impact strength decreased. The tensile and flexural strength, flexural modulus increased as the compatibilizer content increased from 2 to 4%, but impact strength was decreased. The structural examination of the wood polymer nanocomposite with X-ray showed that nanoclay was distributed as intercalation structure in polymer matrix, and the d-spacing of layers were increased with increasing of nanoclay particles content.
Habib alah Khademi eslam; Razieh Baghbani; Esmaeil Ghasemi; Behzad Bazyar
Abstract
Flexural strength, modulus and tensile strength of composites made from treated baggase flour/recycled polyethylene was investigated. Baggase flour (40 mesh particles) was treated with 10% hydroxide sodium for 45 minutes. Then, the composites were manufactured using injection molding method using both ...
Read More
Flexural strength, modulus and tensile strength of composites made from treated baggase flour/recycled polyethylene was investigated. Baggase flour (40 mesh particles) was treated with 10% hydroxide sodium for 45 minutes. Then, the composites were manufactured using injection molding method using both treated and virgin baggase flour as filler (46 and 26%), and recycled and virgin polyethylene as matrix. Flexural strength of the composites made from treated fiber was superior to the relevant untreated fibers. Chemical modification of bagasse fiber improved the tensile strength. Increasing the fiber ratio from 26 to 46%, increased the flexural strength, modulus and tensile strength of the composite. Flexural and tensile properties of the composites produced using recycled HDPE were identical to those based on virgin HDPE.
Hassan Ziaei Tabari; Amir Nourbakhsh; Habibollah Khademi Eslam; behzad baziyar
Abstract
The aim of this study was to investigate the potential of using reed flour and different contents of montmorillonite (nanoclay) nanoparticles on the physical and tensile properties of polypropylener/reed flour/nano clay composite. The amount of coupling agent and reed flour was constant at 5% and 40%, ...
Read More
The aim of this study was to investigate the potential of using reed flour and different contents of montmorillonite (nanoclay) nanoparticles on the physical and tensile properties of polypropylener/reed flour/nano clay composite. The amount of coupling agent and reed flour was constant at 5% and 40%, respectively and nanoclay content, adjusted at four levels of 0, 1, 3 and 5% were considered. The materials were mixed in an internal mixer and the samples were prepared by injection molding method. The specimens were tested in accordance with EN ISO 527 standard test method for tensile properties (tensile strength and module) and elongation at break. Physical properties such as water absorption and thickness swelling were measured. The results of tensile moduli and strengths, elongation at break and physical properties (water absorption) showed improvement by the addition of nanoclay up to 3%.
Nader Maili; Mohammad Talaei; Habib alah Khademi eslam; Behzad Bazyar
Abstract
In This Study,Effect of Enzymatic Deinking on Mechanical Strength of old newspaper was investigated .The protocol for the enzymatic treatment of old newspaper on a laboratory scale using cellulase and combination of callulase:lipase was developed as an effective method for paper recycling.
The deinking ...
Read More
In This Study,Effect of Enzymatic Deinking on Mechanical Strength of old newspaper was investigated .The protocol for the enzymatic treatment of old newspaper on a laboratory scale using cellulase and combination of callulase:lipase was developed as an effective method for paper recycling.
The deinking conditions of pulping consistency of 4% with the pulping time of 2/5 min.temperature 20 and 50 C.at neutral PH.
The study focused on analyzing the effects of enzyme treatment on mechanical strength of old newspaper.
The results showed that enzymatic treatment increases the mechanical strengths of the treated pulp compared to the control pulp.Also, the effect of combination of cellulase and lipase on improvement of mechanical strengths of pulp is more than cellulase treatment alone.
Management and Economics wood
Arash Hassan poor; Behzad Bazyar; Habib alah Khademi eslam; Amir Hooman Hamasi
Abstract
Wood polymer composites (wpc) have been extracting used for building Products, Automotive, Packaging materials and another applications. Wpc is subject to fungal attack due to wood components. Early detection of wood decay is critical because decay fungi can cause mass loss and rapid structure failure. ...
Read More
Wood polymer composites (wpc) have been extracting used for building Products, Automotive, Packaging materials and another applications. Wpc is subject to fungal attack due to wood components. Early detection of wood decay is critical because decay fungi can cause mass loss and rapid structure failure. The objective of this study was to compare the effects of two fungi Trametes versicolorand Coniophora puteana on the mass loss of wood plastic composites. Specimens as four various treatments: contain 40,50,60,70 percent of wood flour in composition, were exposed to brown rot and white rot for 4, 8, 12, 16 week. After each of mentioned time Mass loss was measured and its amount increased for each of treatments. As seen, most amount of mass loss occurred on 16th week after contamination and in samples with 70% wood flour about two fungi .Results shown that contamination time and wood flour percent in composition have direct correlation with composites mass loss. Also at same treatments and contamination times white rot has more severe effects on mass loss factor than brown rot.
