Pulp and paper
somayeh heydari; Ahmad Reza Saraeyan; Mohamadreza Dehghani firozabadi; Alireza Shakeri; babak shokri
Abstract
Ethylene vinyl alcohol (EVOH) copolymer is of semi crystalline materials with excellent barrier properties to gases. Also, it has shown outstanding chemical resistance. Despite its low gas permeability, EVOH copolymer displays poor water and water vapor resistance. In this study, Trimethoxymethylsilane ...
Read More
Ethylene vinyl alcohol (EVOH) copolymer is of semi crystalline materials with excellent barrier properties to gases. Also, it has shown outstanding chemical resistance. Despite its low gas permeability, EVOH copolymer displays poor water and water vapor resistance. In this study, Trimethoxymethylsilane (as hydrophobic coating) was deposited by Plasma Enhanced Chemical Vapor (PECVD) method on the coated paper with Ethylene vinyl alcohol in order to improve the paper's barrier properties of moisture transmission. Coating by PECVD method was done in the certain conditions of time 6 min and pressure 300 m Torr. Different treatments were applied for power including 50, 70 and 90W.Then contact angle was measured in order to determined improvement of the paper's barrier properties of moisture transmission . The result showed that papers which were coated with Trimethoxymethylsilane had higher contact angle water 55.7% more than the control. The results revealed that the best condition was obtained by 50 W power. The structural and chemical properties of deposited layer were observed with Fourier Transform infrared spectroscopy- Attenuated Total Reflectance (FTIR-ATR) and Energy Dispersive X-ray Spectroscopy (EDS). The results confirmed bonding of silane on the surface EVOH polymer.
Pulp and paper
somayeh heydari; Ahmad Reza Saraeyan; Mohammad Reza Dehghani Firouzabadi; Alireza Shakeri; babak shokri
Abstract
DOR:98.1000/1735-0913.1398.34.100.66.1.9.1604 In this study, EVOH was coated on paper made of CMP pulp by extrusion method in order to improve the paper's barrier properties of oxygen transmission. Ethylene vinyl alcohol (EVOH) shows poor moisture resistance despite less gas permeability. Then, dimethoxydimethylsilane ...
Read More
DOR:98.1000/1735-0913.1398.34.100.66.1.9.1604 In this study, EVOH was coated on paper made of CMP pulp by extrusion method in order to improve the paper's barrier properties of oxygen transmission. Ethylene vinyl alcohol (EVOH) shows poor moisture resistance despite less gas permeability. Then, dimethoxydimethylsilane was deposited using Plasma Enhanced Chemical Vapor Deposition on EVOH film as the hydrophobic layer. A random factorial experiment was designed with three factors at three levels including time (6-8-10 min), pressure (30-0400-500 m Torr), and radio frequency power (50-70-90 W). The contact angle, oxygen transmission rate, tensile strength, and strain energy were measured to obtain the optimum condition. Expert Design method using response surface was used to optimize the condition coating Dimethoxydimethylsilane in order to improve the hydrophobic properties, reduce OTR, increase tensile strength and strain energy. Based on this method the optimum condition was suggested as: time 6 min, pressure 499.99 m Torr and power 50W. Keywords: Extrusion , Contact angle, Oxygen transmission rate, Response Surface methodology.
Pulp and paper
Ahmad reza Saraeyan; Somayeh Heidari; Ahmad reza Shakeri
Abstract
Increased environmental concerns over the use of certain synthtic packaging in combination with consumer demands led to increased interest in alternative packaging materials research. Paper is biodegradable and widely used in packaging applications therefore perfectly safe for the environment. In an ...
Read More
Increased environmental concerns over the use of certain synthtic packaging in combination with consumer demands led to increased interest in alternative packaging materials research. Paper is biodegradable and widely used in packaging applications therefore perfectly safe for the environment. In an effort to produce more environmentally friendly materials, renewable and biodegradable biopolymers have been utilized as paper coating substances. in this study carried out to determine effect of the four type of biopolymers such as anionic starch, chitosan, polyvinyl alcohol and etylenvinyl alcohol, on the smoothness, Water absorption, air resistance, burst Index properties paper made of bagasse soda pulp. Coating done whith coater tester. Coating weight was 3-6 g/m2. The results of the mechanical and physical properties of the handsheets showed that, led to increase index burst handsheets coated with etylenvinyl alcohol and anionic starch indices as 34.4 and 26.26% compared to control sample. Air resistance and smoothness was for coated paper with starch more than control sample indices as 173.23 and 18.73%. also coated paper with chitosan showed minimum value..
