Pulp and paper
farzaneh shiralizadeh; mohammad azadfallah; ali Abdolkhani; mohammad Layeghi; saeed mahdavi
Abstract
This study was conducted with the aim of producing laboratory samples of transparent paper using overbeating method. Hence, bagasse bleached soda pulp was subjected to post-bleaching sequence of DED to remove residual chromophores. Then this pulp was refined in a PFI mill to reach different ...
Read More
This study was conducted with the aim of producing laboratory samples of transparent paper using overbeating method. Hence, bagasse bleached soda pulp was subjected to post-bleaching sequence of DED to remove residual chromophores. Then this pulp was refined in a PFI mill to reach different levels of 55, 130, 200, and 260 mL,CSF (Canadian standard freeness) freeness. Then handsheets were made according to TAPPI standard T 205 om– 8. Results indicated that refining has significant effect on optical properties especially transparency so that the maximum value was observed using pulp with the minimum freeness, i.e. 55 ml. The variations of transparency due to refining were also further explained by measuring scattering coefficient, opacity and brightness of the specimens. In addition, mercury porosimetry and analyzing the pictures of scanning electron microscopy (SEM) demonstrated the extensive variations of pore structure in paper during refining which impose great influence on developing transparency.
Amir Nourbakgsh
Abstract
Two recycled polymers (rHTPE and rPP) combined with baggase fibers were used as the reinforcing material to improve the mechanical properties of wood plastic nanoclay composite. The amount of baggase fibers varied at three levels (25, 35 and, 45 percent). Two recycled polymers (rPP and rHDPE) were used ...
Read More
Two recycled polymers (rHTPE and rPP) combined with baggase fibers were used as the reinforcing material to improve the mechanical properties of wood plastic nanoclay composite. The amount of baggase fibers varied at three levels (25, 35 and, 45 percent). Two recycled polymers (rPP and rHDPE) were used as polymer matrix. Tensile, flexural and impact strength properties were measured according to ASTM standard tests. Scanning electron microscopy (SEM) and X-Ray Diffraction (XRD) was performed to interpret the results. The results were statistically analyzed using factorial experimental under completely randomized block design and the averages were compared using DMRT. The application of 35 percent bagasse fibers as compared with 25 and 45 percent increased the strength of wood plastics composites. However, higher impact strength was reached using 25% bagasse fibers as compared with either 35 or 45% bagasse fibers. rHDPE nano-clay composite showed higher tensile, flexural and impact properties compared with rPP. Imaging the morphology of nano-clay by X-Ray diffraction and scanning electron microscopy showed the distribution of nano-clay particles in polymer structure and intercalation was observed.
Mysam Abdolali sarbandi; Vahid Safdari; Sayed javad Sepidedam; Esmaeil Ganjyan
Abstract
In this research, the properties of cement fiberboard produced using different contents of nano-silica and bleached bagasse fibers were evaluated. Different ratios of bagasse fibers, cement and nano-silica were blended using an electrical blender. The mixture was then poured into a mould (15x18x18 ...
Read More
In this research, the properties of cement fiberboard produced using different contents of nano-silica and bleached bagasse fibers were evaluated. Different ratios of bagasse fibers, cement and nano-silica were blended using an electrical blender. The mixture was then poured into a mould (15x18x18 cm dimension). The produced mould samples were matured for 14 days at room temperature and high moisture content (100%) and after maturing, the bending strength and physical properties of boards were measured. Results showed that both materials (naosilica and bagasse fibers) changed the bending and physical properties of the final boards. The bending strength of samples increased with the increase in nano-silica up to 1% and exceeding 1% decreased this property. It is because high content of silica (more than 1%) results in aggregate of nano-silica and cement and micro cracks occurred in samples. Also the increase in bagasse fiber up to 4% increased of bending strength of boards and more bagasse fibers decreased the bending strength. It is because high bagasse fibers cannot distribute in the cement matrix and fiber bundles reduced the bending strength. However, as the nano-silica and bagasse fibers content increase, the water and moisture absorption as well as thickness swelling increases, whereas density decreases.
Composite wood products
Hamed Nasiry; Ali Varshoei; Abolfazl Kargarfard
Abstract
In this study the possibility of bagasse fiber usage in Fiber-Cement Composite (FCC) manufacturing, was investigated. Two load of bagasse fiber (%4, 10), three level of calcium chloride as facilitator (5, 7.5 and 10 percent per dry weight of cement) and two type of Portland cement (type II and V) were ...
Read More
In this study the possibility of bagasse fiber usage in Fiber-Cement Composite (FCC) manufacturing, was investigated. Two load of bagasse fiber (%4, 10), three level of calcium chloride as facilitator (5, 7.5 and 10 percent per dry weight of cement) and two type of Portland cement (type II and V) were considered as variables (12 treatments). There were three replicates for each treatment, thus 36 experimental board were manufactured totally. The physical and mechanical properties of experimental specimens were investigated and results analyzed by SPSS software as fully randomized factorial model. As results indicated, there was no significant different between cement type II and V in physical and mechanical properties. The increased loads of calcium chloride caused a striking reduction in mechanical properties and increased water absorption amounts. The best bending strength, modulus of elasticity, IB and minimum thickness swelling were reported in treatment with 4% fibers, 7.5% calcium chloride and type II cement.
