khadijeh armand; ali ghasemiyan
Abstract
In this research, the effect of sodium peroxide and sodium hypochlorite on the chemical-mechanical pulp bleaching (CMP) has been investigated. For this purpose, unbleached CMP pulp was produced from Mazandaran wood and paper mill, and bleaching with hydrogen peroxide and sodium hypochlorite was carried ...
Read More
In this research, the effect of sodium peroxide and sodium hypochlorite on the chemical-mechanical pulp bleaching (CMP) has been investigated. For this purpose, unbleached CMP pulp was produced from Mazandaran wood and paper mill, and bleaching with hydrogen peroxide and sodium hypochlorite was carried out in two levels of 3 and 4%, during both 60 and 90 minutes in 70°C at 8% consistency. In each treatment, 30 grams of pulp with hydrogen peroxide, sodium silicate, DTPA, sodium hydroxide and sodium hypochlorite for bleaching were prepared. In the following 60 gr/m2 hand sheets were prepared and the optical properties of hand sheets were measured and analyzed based on TAPPI.The results obtained from the review of optical properties of handsheets show that by increasing the bleaching time and the level of chemicals the optical properties was improved. So that the highest brightness and minimum yellowness were observed in the 4% and 90 minutes in bleaching whit hydrogen peroxide. the lowest opacity in the control sample. Resistance properties such as tensile, burst and tear strength of bleached paper were also increased.
Pulp and paper
Maryam Alipoor; Ghasem Asadpur Atouei; Seaid Majid Zabihzadeh; Zohreh Ghazvini
Abstract
With considering that in chemical-mechanical pulp (CMP) production process , the wood chips washing pre-treatment is important , so this research was conducted to investigate the effect of pre-treatment washing of populous deltoids wood chips on CMP Optical(brightness and opacity) and Strength(tensile ...
Read More
With considering that in chemical-mechanical pulp (CMP) production process , the wood chips washing pre-treatment is important , so this research was conducted to investigate the effect of pre-treatment washing of populous deltoids wood chips on CMP Optical(brightness and opacity) and Strength(tensile and burst indexes) properties. Pre-treatment was accomplished with pure hot water and alkaline solutions (NaOH) at three levels of 0.5, 2 and 3.5 percent too. Pre-treated populous deltoids wood chips and control (chips without washing) were converted to pulp by CMP process. The results of this research indicated that the pretreatment of populous deltoids wood chips with hot water and also alkaline solutions caused wood chips mass and using of these treated chips for pulping caused pulp yield and brightness increscent, pulp strength reduction and also energy consumption increscent. . Removing of some part of chips hemicellulos have negative effect on the pulp refinability and cause pulp strength reduction.
Pulp and paper
Mehrnoosh Tavakoli; saraeyan ahmad reza; hossein resalati; ali ghasemian
Abstract
The present study was carried out aiming to investigate the effect of using Deinked Mixed Office Waste Pulp (MOW) on the properties of Alkaline Peroxide Mechanical Pulp (APMP) from cotton stalk. APMP pulps was prepared using chelating agents such as Na2SiO3 and DTPA (control sample) and without ...
Read More
The present study was carried out aiming to investigate the effect of using Deinked Mixed Office Waste Pulp (MOW) on the properties of Alkaline Peroxide Mechanical Pulp (APMP) from cotton stalk. APMP pulps was prepared using chelating agents such as Na2SiO3 and DTPA (control sample) and without these agents in two-stage pulping withL/Wratio 6:1(ml/g), 20 minutes impregnation time at 70 0Cfor firststage, 60 minutes impregnation at 75 0Cfor second stage. Also, pulp was preparedfrommixed office waste paper, whichweredeinked with conventional flotation and then each pulp was separately refined up to about 300 ml CSF. The handsheets were made from control sample pulps, APMP without chelating agents, MOW deinked pulp and mixing with 10%, 20% deinked pulp with control APMP. Physical and mechanical properties were determined using TAPPI standard methods. Deinked MOW pulp had the maximum values of density, brightness, strength properties and APMP pulp without chelating agents had the minimum values. Among mixed pulps, APMP pulp containing 20% deinked MOW pulp showed the maximum value of density, brightness, burst index and tear index.
Pulp and paper
Mostafa Nikkhah Dafchahi; Hossein Resalati
Abstract
This research was performed to evaluate the potential of acid pre-hydrolysis soda-AQ process for the production of dissolving pulp including high α-cellulose content from Populus deltoides. To achieve the aim, a pre-hydrolysis liquor containing 0.06% acid sulfuric, soda-AQ pulping, and OD0ED1 bleaching ...
Read More
This research was performed to evaluate the potential of acid pre-hydrolysis soda-AQ process for the production of dissolving pulp including high α-cellulose content from Populus deltoides. To achieve the aim, a pre-hydrolysis liquor containing 0.06% acid sulfuric, soda-AQ pulping, and OD0ED1 bleaching sequence were used. The results show that using at least 0.40 kappa factor at D0 stage was necessary to gain access a high quality dissolving pulp including characteristics like having brightness level and α-cellulose content higher than 86% and 98%, respectively. A kappa reduction of 40.3% was achieved by performing a single stage oxygen delignification after soda-AQ pulping to drop kappa number of pulp from 14.1 to 8.4 prior to entrancing the pulp into the final bleaching stage. The results illustrated that producing acid pre-hydrolyzed soda-AQ dissolving pulp including high α-cellulose content and brightness, and even viscosity is completely feasible through controlling and optimizing the acid pre-hydrolysis, pulping, oxygen delignification stages, and D0ED1 bleaching sequence.
Pulp and paper
Seyed_Pedram Hashemi; Asghar Tabei; Seyyed Peyman Hashemi
Abstract
In this study the effect of different values of peroxide in three levels 3%, 4%, 5% and sodium hydroxide in two levels 2%, 3%, on bleaching of tobacco stalks ( Nicotiana tabacum L. 'PVH 19') soda pulp was investigated. Tobacco stalks were soda pulped using 22% alkali in 170°C for 100 minutes. Produced ...
Read More
In this study the effect of different values of peroxide in three levels 3%, 4%, 5% and sodium hydroxide in two levels 2%, 3%, on bleaching of tobacco stalks ( Nicotiana tabacum L. 'PVH 19') soda pulp was investigated. Tobacco stalks were soda pulped using 22% alkali in 170°C for 100 minutes. Produced pulp had 37.1 % yield and kappa number 62. Bleaching process included two stages: chelating and alkali peroxide bleaching. Results indicated that brightness increased and kappa number decreased by increasing sodium hydroxide and peroxide Hydrogen level.The data related to 3% caustic soda and 5% peroxide treatment without chelating stage, indicated that initial chelating stage significantly affected on the brightness, kappa number and yield of the bleached pulp, and this treatment had the lowest brightness and the highest kappa number and yield among all treatments. Finally, 3% caustic soda-5% peroxide treatment with initial chelating stage had the highest brightness (44.50%) and the lowest yield (83.20%), was selected as the best treatment.
Pulp and paper
Saeideh Sharifi; Ahmad reza Saraeyan; Hossein Resalati
Abstract
Preparation and pre-treatment of raw material influences the pulp production time and color elimination. Pulp consistency during the treatment also influences the color reaction. In the preparation of the APMP pulp, bagasse was pretreated by either boiling water, 1% NaOH as well as 1% NaOH + 1% ...
Read More
Preparation and pre-treatment of raw material influences the pulp production time and color elimination. Pulp consistency during the treatment also influences the color reaction. In the preparation of the APMP pulp, bagasse was pretreated by either boiling water, 1% NaOH as well as 1% NaOH + 1% H2O2. The liquor to bagasse ratio, treatment time and temperature of alkaline peroxide treatment were constant as 10:1, 30 min, and 70 °C respectively. The treatment duration was determined so that at least five percent of the initial hydrogen peroxide remained at the end of chemical treatment. Characteristics of hand sheets were determined according to the TAPPI standard. The results showed that, the duration of the treatment for pulp consistency of 10, 15 and 20% was 50, 30 and 10 minute, for sample pretreated with boiling water and 290, 230 and 170 minute for the sample pretreated with 1% NaOH + 1% H2O2. The highest brightness of the paper reached with bagasse pretreated in boiling water at 20 % consistency.
Iman Akbarpoor; Hossein Resalti; Ali Solimani
Abstract
In this study, the effect of elimination and relative decrease of sodium silicate along with substituting the organic complex of sulvy-x was investigated on optical properties of CMP pulp bleached by hydrogen peroxide. The brightness of paper were increased to 66.8%, yellowness decreased to 22% and opacity ...
Read More
In this study, the effect of elimination and relative decrease of sodium silicate along with substituting the organic complex of sulvy-x was investigated on optical properties of CMP pulp bleached by hydrogen peroxide. The brightness of paper were increased to 66.8%, yellowness decreased to 22% and opacity decreased to 80% with increase in sodium silicate charge from 0.7% to 3%. Also, with complete elimination of sodium silicate and using of sulvy-x at different levels of 0.4, 0.5, 0.7 and 1% , highest brightness and lowest yellowness were shown at 0.5% sulvy-x. These values were 66.1% and 21.8%, respectively. The brightness of paper enhanced from 61.2% to 67.3% with increasing of sulvy-x charge from 0.4% up to 0.5% blended with constant value of 0.7% sodium silicate. But the brightness decreased at higher levels. Generally, pretreatment by DTPA prepared the paper with lower brightness and higher yellowness at two different states namely silicate-free and silicate-containing with sulvy-x. Pretreatment by DTPA at silicate-free state led to decrease of opacity but at silicate-containing state terminated to improve of opacity values. Increasing of bleaching time up to 120 minutes resulted in the paper with higher brightness, higher opacity and lower yellowness at silicate containing state with sulvy-x. At silicate-free state, increasing of bleaching time up to 120 minutes led to improve of opacity while brightness improved and yellowness reduced with increase in bleaching time to 90 minutes. Also, the brightness of paper decreased at higher times (120 minutes) and yellowness increased. In conclusion, achieved results from comparison of optical properties of paper produced from peroxide bleaching of hardwood CMP pulp indicated that we could produce the paper with desirable or even better optical properties by replacing of sulvy-x rather than sodium silicate compared to conventional peroxide bleaching.
Somayeh Ghasemi; Rabie Behroz
Abstract
Using high consistency pulp especially in bleaching plant is highly attractive due to considerable reduction in energy and water consumptions and low effluent volume. This research investigates the effect of consistency CMP pulp on bleaching by hydrogen peroxide. For this purpose, unbleached mixed hardwood ...
Read More
Using high consistency pulp especially in bleaching plant is highly attractive due to considerable reduction in energy and water consumptions and low effluent volume. This research investigates the effect of consistency CMP pulp on bleaching by hydrogen peroxide. For this purpose, unbleached mixed hardwood CMP pulp of Mazandaran wood and paper CO. mill was used. Bleaching was carried out with QP sequences. Pretreatment or Q stage was carried out by DTPA as a chelating agent for removing transition metals. Chelating stage had a similar condition for all pulps. bleaching with hydrogen peroxide was carried out in three levels of hydrogen peroxide 2, 3, 4% and proportion NaOH to H2O2: 0.8, 0.7, 0.6 by adding 3% sodium silicate in 70˚C and 150min at four consistency level (10, 15, 25 and 30%). After bleaching, handsheets were made with grammage 60gr/m2 from bleached pulp. The experimental results showed that high brightness and opacity and lower yellowness was obtained at 30% consistency by 2 and 3% peroxide charge. However, by using 4% hydrogen peroxide, higher brightness and lower yellowness attained at 25% consistency. Brightness is increased continuously by increasing consistency from 10 to 30% at 2, 3% peroxide. But at 4% peroxide charge, brightness is increased from 10, 15 and 25%, and then at 30% consistency is decreased significantly. Also under conditioning of 2% peroxide and 30% consistency and 2% peroxide at 25% consistency can obtain similar brightness to 3% peroxide and 25% consistency and 4% peroxide at 10% consistency. That it means of 25, 30% decrease in consumption peroxide and sodium hydroxide.
Hossein Shob chary; Ahmad reza Saraeyan; Ali Ghasemian
Abstract
This study was conducted to investigate the properties of cotton stalks APMP pulp. APMP prepared from chipped cotton stalks. the pulps were prepared separately from debarked and bark containing stalks using three two-stage treatments.Sodium hydroxide charge as a constant level of 4% and hydrogen ...
Read More
This study was conducted to investigate the properties of cotton stalks APMP pulp. APMP prepared from chipped cotton stalks. the pulps were prepared separately from debarked and bark containing stalks using three two-stage treatments.Sodium hydroxide charge as a constant level of 4% and hydrogen peroxide at three levels of 0, 1 and 2% were used in to two-stages, sodium hydroxide as a constant level of 2% and hydrogen peroxide at three levels of 2, 3, 4% were applied. Other conditions of pulping was time's of 20 min for first stage and 100 min for second stage, temperature 70°C and l/w:6:1 as fixed factors considered. Pulp yield determined after neutralization and defiberation. All the pulps were refined up to 300 (ml, CSF) freeness and handsheets were made, then and properties of papers measured using TAPPI standards. Results showed that the pulp yield and brightness was higher in free-bark compared to bark-containing conditions. Also paper produced in free-bark condition with cotton stalks core, resulted the higher tensile and burst indexes and higher breaking length compared to whole cotton stalk.While tear index didn’t show significant difference.Generally, caliper and bulk rates were high in total treatments (free-bark and bark-containing conditions) from cotton stalk APMP process.
Meisam Aliabadi; Eiman Akbaepoor; Ahmad reza Saraeian
Abstract
In this study, the effect of organic complex "sulvy-x" on the optical properties of hornbeam CMP pulp bleached with hydrogen peroxide was investigated. Sulvy-x was used in two sequences silicate-free and silicate containing in hydrogen peroxide bleaching. The brightness of papers increased to 60.52 and ...
Read More
In this study, the effect of organic complex "sulvy-x" on the optical properties of hornbeam CMP pulp bleached with hydrogen peroxide was investigated. Sulvy-x was used in two sequences silicate-free and silicate containing in hydrogen peroxide bleaching. The brightness of papers increased to 60.52 and the yellowness decreased to 22.6 with increasing silicate charges up to 1% . However, at higher levels than 1% , the brightness decreased and the yellowness increased. Without dosage of sodium silicate but using 0.5% of sulvy-x, maximum brightness of 59.3% and minimum yellowness of 23.4 % ISO was achieved. In silicate-containing bleaching, combination of 0.5% sulvy-x and 0.7% sodium silicate resulted the highest brightness (60.28 % ISO) and the lowest yellowness (23 % ISO). Optimum charge of sodium hydroxide and hydrogen peroxide were determined as 2.5% and 5%.The best time for bleaching of hornbeam CMP pulp was 90 minutes in either sequences. With regard to results obtained, utilization of the organic complex of sulvy-x could be a suitable substitution for sodium silicate which produces the pulp with higher brightness and lower yellowness in conventional peroxide bleaching.
Pulp and paper
Iman Akbarpour; Hossein Resalati
Abstract
This research was accomplished in order to investigate the replacement of organic complex of Glanapone Stab with sodium silicate on optical properties of hardwood CMP pulp bleached by hydrogen peroxide. The highest brightness of 65.5% and the lowest yellowness of 21.6% was attained at silicate-free ...
Read More
This research was accomplished in order to investigate the replacement of organic complex of Glanapone Stab with sodium silicate on optical properties of hardwood CMP pulp bleached by hydrogen peroxide. The highest brightness of 65.5% and the lowest yellowness of 21.6% was attained at silicate-free followed by replacement of 0.7% and 1.5% Glanapone. But the highest opacity 98.2% was gained using 0.5% glanapone. The brightness of paper increased to 68.1% and the yellowness decreased to 20.8. by adding of glanapone consumption from 0.4% to 0.5% in blended with 0.7% sodium silicate. At higher levels than 0.5% glanapone, the brightness of paper decreased and the yellowness increased. Using Higher levels of 1 and 1.5% glanapone in blended with 0.7% sodium silicate resulted the highest opacity 97.9% and 98%, respectively. Increasing of peroxide usage up to 5% at two different states of silicate-free and silicate-containing with glanapone resulted in the paper with higher brightness and lower yellowness and opacity. CMP pulps bleached at 120 minutes resulted the highest brightness of 71.1% and the lowest yellowness of 18.3% at silicate-containing state with glanapone. Maximum opacity of 98.3% and 98% were shown at bleaching time 30 minutes at two states silicate-free and silicate-containing state with glanapone, respectively. In this research with regard to optical properties in relation to paper produced from CMP pulp bleaching at two states silicate-free and silicate-containing with glanapone,it can be said that possibility of producing the paper with similar optical properties or even better using 0.7% or 1.5% at silicate-free is in compared to conventional hydrogen peroxide bleaching. Also, we could produce the paper with higher brightness along with lower yellowness and similar opacity followed by bleaching time of 120 minutes and hydrogen peroxide 5% in combination of 0.7% sodium silicate with 0.5% glanapone in compared to higher consumed values of sodium silicate.
