Pulp and paper
Mehrnoosh Tavakoli; saraeyan ahmad reza; hossein resalati; ali ghasemian
Abstract
The present study was carried out aiming to investigate the effect of using Deinked Mixed Office Waste Pulp (MOW) on the properties of Alkaline Peroxide Mechanical Pulp (APMP) from cotton stalk. APMP pulps was prepared using chelating agents such as Na2SiO3 and DTPA (control sample) and without ...
Read More
The present study was carried out aiming to investigate the effect of using Deinked Mixed Office Waste Pulp (MOW) on the properties of Alkaline Peroxide Mechanical Pulp (APMP) from cotton stalk. APMP pulps was prepared using chelating agents such as Na2SiO3 and DTPA (control sample) and without these agents in two-stage pulping withL/Wratio 6:1(ml/g), 20 minutes impregnation time at 70 0Cfor firststage, 60 minutes impregnation at 75 0Cfor second stage. Also, pulp was preparedfrommixed office waste paper, whichweredeinked with conventional flotation and then each pulp was separately refined up to about 300 ml CSF. The handsheets were made from control sample pulps, APMP without chelating agents, MOW deinked pulp and mixing with 10%, 20% deinked pulp with control APMP. Physical and mechanical properties were determined using TAPPI standard methods. Deinked MOW pulp had the maximum values of density, brightness, strength properties and APMP pulp without chelating agents had the minimum values. Among mixed pulps, APMP pulp containing 20% deinked MOW pulp showed the maximum value of density, brightness, burst index and tear index.
Chemical conversion
mahdiye mazandarani; ali ghasemian; ahmadreza Saraeyan; mahdi mashkour; SeyedRahman Jafari Petroudy
Abstract
In the present study, preparation of cotton stalk (Sahel variety) as one of the common agricultural residues was studied through three stages as Soda-AQ chemical pulping, delignification and alkaline treatment, aiming for the production of cellulose nanocrystal. In order to identify the optimum condition ...
Read More
In the present study, preparation of cotton stalk (Sahel variety) as one of the common agricultural residues was studied through three stages as Soda-AQ chemical pulping, delignification and alkaline treatment, aiming for the production of cellulose nanocrystal. In order to identify the optimum condition for the preparation of cellulose nanocrystal, acidic hydrolysis of the produced alpha-cellulose was done using 64% sulfuric acid, 25, 35 and 45 minute as time and at 35, 45 and 55 degree centigrade as temperature. Atomic Force Microscopy (AFM), X-Ray Diffraction, and Dynamic Light Scattering (DLS) were used to identify the quantitative and qualitative properties of cellulose nanocrystals. AFM micrographs showed that more severe condition of the treatments decreased the thickness of the cellulose nanocrystals. XRD results also demonstrated that the preparation stages of alpha-cellulose as well as acidic hydrolysis treatments much effectively increased the degree of crystallinity. DLS results indicated that 98.7 percent of the produced nanocrystals under the condition of 55 degree centigrade and 45 minute were in the range of 18-95 ηm, whose highest abundance was in the range of 18-39 ηm. Thus, the mentioned condition were determined as the best and optimum condition for the production of cellulose nanocrystal from cotton stalk cellulose.
Composite wood products
mahdi abasyan; asghar omidvar; mahdi mashkour; zinat farhadi
Abstract
This study seeks to investigate the possibility of producing polypropylene composite- cotton stalk flour with various percentages of cotton stalk flour. Determining the best treatment in terms of physical and mechanical properties and exploring the effect of using cotton stalks in the production of the ...
Read More
This study seeks to investigate the possibility of producing polypropylene composite- cotton stalk flour with various percentages of cotton stalk flour. Determining the best treatment in terms of physical and mechanical properties and exploring the effect of using cotton stalks in the production of the composites were among the major objectives of this study. Six treatments consisting of Polypropylene, 40, 55 and 70 percent level of cotton stalks and two fillers (cotton stalks with and without barks) were developed. Maleic anhydride modified polypropylene (3% wt) was applied to each treatment. The mixing and granulation of the plastic and cotton silk flour was carried out using twin screw extruder model 4815. After preparing and shearing of samples, the mechanical properties of composites including tensile strength, rupture modulus and elasticity modulus were calculated in accordance with D-6109 and ASTM D-7031 standards. In addition, water absorption and thickness swelling tests were performed according to D-570-98 standard. The results showed that an increase in the flour of cotton stalk reduced the tensile strength and rupture modulus on the one hand, and increased the bending elasticity modulus on the other hand. In terms of the performance of the filler, there was a significant difference between values of rupture modulus and elasticity modulus at 95% level whereas this difference was not significant for tensile strength. Moreover, this difference was significant for values of water absorption and thickness swelling. The maximum tensile strength belonged to T4 with 40 percent of cotton stalk bark fibers.
Physics and Mechanical Wood
Shamohammad Amiri
Abstract
Anatomical, chemical and pulping characteristics of Cotton stalk as a nonwood material.Fiber length, fiber diameter, lemun and cell wall thickness were measured at 24.47, 16.43 and 4.02 mn respectively. Paper making coefficients were also calculated coefficient, flexibility coefficient and ranckl ...
Read More
Anatomical, chemical and pulping characteristics of Cotton stalk as a nonwood material.Fiber length, fiber diameter, lemun and cell wall thickness were measured at 24.47, 16.43 and 4.02 mn respectively. Paper making coefficients were also calculated coefficient, flexibility coefficient and ranckl coefficient were calculated at 34.28, 67.14 and 48.93 respectively.Chemical composition of cotton stalk was determined at 47.83%cellulose, 21.66% lignin, 2.13% alcohol-acetone extractives and 2.83% ash.Soda pulping at following variables was investigated. Three levels, of cooking temperature (140, 160 and 180 degree Celsius), three cooking time (30, 40 and 50 minutes) and raw material condition (normal and debarked stalks). Active alkali of 20% (based on NaOH) and liquor to wood ratio of 5: 1 were kept constant for all soda cooks. The optimum combination of variables160 degree Celsius I temperature, 40 minutes time and debarked raw material. The yield and kappa no. of pulp obtained at this cooking condition was 50.4% and 89.15 respectively.
