Composite wood products
masoudreza habibi; Hossein Hosseinkhani; Saeed Mahdavi
Abstract
In this study , MDF was produced from three clones of poplar (P.e. vernirubensis, P.e. costanzo, P.e.561.41). Age clones of poplar were 4 and 12 years. In addition to age variation , the influence of three production variables (steaming time , press time and resin content on MDF properties were investigated. ...
Read More
In this study , MDF was produced from three clones of poplar (P.e. vernirubensis, P.e. costanzo, P.e.561.41). Age clones of poplar were 4 and 12 years. In addition to age variation , the influence of three production variables (steaming time , press time and resin content on MDF properties were investigated. Variations of each variable were as follow:
- Steaming time (5, 10, 15 minutes)
- Press time (3, 4, 5 minutes)
- Resin content (9%, 11%)
Fiber length and fiber diameter of 4 and 12 years old poplar clones (P.e. vernirubensis, P.e. costanzo, P.e.564.41) were measured 746, 25.23, 805, 25.76,751, 25.44 and 902, 31.62, 995, 29.23, 899, 26.83 micron respectively.
MOR, MOE, IB, TS2, TS24 were determined according to DIN standard.
Increasing steaming time decreased board's internal bond and bending properties. As expected, boards demonstrated better properties at higher resin consumption. Minimum of boards thickness swelling were obtained at 15 minutes steaming time because of fiber hydrophilic properties were decreased. There are no significant differences between 4 and 12 years old of clones for bending properties and IB of boards. The effect of age variation is only significant difference on thickness swelling of boards which it is lower for 4 years old clones.
Composite wood products
masoudreza habibi; Saeed Mahdavi; Hossein Hosseinkhani
Abstract
In this study, MDF was produced from Reed ( Phragmites australis ). Reeds are collected from Talabe - Anzalye areas. The treatments conditions for fiber preparing were as follows:-Steaming temperature 170°c, 180°c-Steaming time 5, 10, 15 minutesThe other production variables were constant. The ...
Read More
In this study, MDF was produced from Reed ( Phragmites australis ). Reeds are collected from Talabe - Anzalye areas. The treatments conditions for fiber preparing were as follows:-Steaming temperature 170°c, 180°c-Steaming time 5, 10, 15 minutesThe other production variables were constant. The anatomical properties of Reed such as fiber length, fiber diameter, lumen cell diameter, and cell wall thickness were measured respectively 1.38mm, 17.07, 6.15, 5.46 micron. LID ratio of Reed fiber was measured 80.84. The physical and mechanical properties of MDF were determined according to DIN standard. The measurements of bending properties and IB of MDF revealed that increasing steaming time and steaming temperature caused to decrease MOR, MOE and IB.Also the results of MDF dimentional stabilities indicated that Thickness Swelling after 2 and 24 hours decreased upon increasing steaming time and steaming temperature. Degradation of hemicellulose chains may be the reason of decreasing Thickness Swelling.
Pulp and paper
Kamyar Salehi; Abdolrahman Hosseinzadeh; Hossein Familian
Abstract
In order to investigate the possibility of utilizing cotton stem in cellulosic industries chemical, physical and anatomical properties of cotton stem (var. varamin) was investigated.Cotton wood fiber length, fiber diameter, lumen diameter and cell wall thickness was measured at 840 mm, 23.9mlm, ...
Read More
In order to investigate the possibility of utilizing cotton stem in cellulosic industries chemical, physical and anatomical properties of cotton stem (var. varamin) was investigated.Cotton wood fiber length, fiber diameter, lumen diameter and cell wall thickness was measured at 840 mm, 23.9mlm, 16/11mm, and 3/9mm respectively.Cotton stem oven-dry density, basic density, and air-dry density were measured at 0/44 gr./cm3, 0.4Ogr/cm3, and .42gr/cm3.Shrinkage and swelling was measured at 7.7 %, 8.3% and porosity was measured at 70.5%.Chemical composition was as follow: cellulose 52%, lignin 29.2%, ash 104% and extractives 6.8%.Anatomical features were as follow: Growth ring boundaries distinct or absent Wood diffuse-porous. Vessels in diagonal or radial pattern grouping:partly solitary partly in radial multiples of 2-4-6 or very small cluster Simple perforation plate. Intervesse pit alternate. Intervessel pit size: minute -< 4mm. Vestured pits absent. Vessel-ray pits with much reduced borders to apparently simple Helical Thickening absent. Mean tangential diameter of vessel lumina 50-100mm. Vessels per square millimeter 20-40 vessels. Mean vessel element length - < 350mm. Tyloses Gums & deposits absent. Fiber with simple to minutely bordered pits. Helical thickening in ground tissue fibers absent.Nonseptate fiber present. Fibers very thin walled. Rays with multi seriate portion as wide as uniseriate portion. Aggregate rays absent. Ray height> 1mm. Body ray cells procumbent with over 4 rows of upright And square marginal cells Ray per millimeter 4-12/mm.
Composite wood products
masoudreza habibi; Saeed Mahdavi; Hossein Hosseinkhani; Sayed javad Sepideh dam
Abstract
In this study, MDF was produced from Reed (Phragmites australis). Reeds are collected from Hor-Alazym area. The treatments conditions for fiber preparing were as following:- Steaming temperature 170, 180oC(Steaming pressure 7,9 bar).- Steaming time 5, 10, 15 minutes.The other production variables were ...
Read More
In this study, MDF was produced from Reed (Phragmites australis). Reeds are collected from Hor-Alazym area. The treatments conditions for fiber preparing were as following:- Steaming temperature 170, 180oC(Steaming pressure 7,9 bar).- Steaming time 5, 10, 15 minutes.The other production variables were constant.The anatomical properties of Reed such as Fiber length, fiber diameter, lumen cell diameter, and cell wall thickness were measured. LID ratio of Reed fiber was measured 73.69. The physical and mechanical properties of MDF were determined according to DIN standard. The measurements of bending properties and IB of MDF revealed that increasing steaming time and steaming temperature caused to decrease MOR, MOE, and IB.Also the results of MDF dimentional stabilities indicated that Thickness Swelling after 2 and 24 hours decreased upon increasing steaming time and steaming temperature. Degradation of hemicellulose chains may be the reason of decreasing Thickness Swelling.
Chemical conversion
Saeed Mahdavi; Abdolrahman Hosseinzadeh; Abbas Fakhryan roghani; masoudreza habibi
Abstract
In order to evaluate reed as a raw material for wood & paper industries, three main regions of Iran consist of south, North and East were selected for this study. Phragmites australis is dominant species in these regions and this study concentrated on it as well.Chemical components and biometry of ...
Read More
In order to evaluate reed as a raw material for wood & paper industries, three main regions of Iran consist of south, North and East were selected for this study. Phragmites australis is dominant species in these regions and this study concentrated on it as well.Chemical components and biometry of fibers were determined with four and thirty replications respectively. Statistical analysis showed that there were no significant differences among three regions in fiber length and lumen diameter but reversely fiber width and cell wall thickness showed significant differences. The highest fiber length mean was 1.39mm. For North (Anzali) Coefficients of papermaking of fibers also were calculated for each region. Biometerical fiber results, showed that P. australis has good fiber compare to the Iranians hardwoods as papermaking.The results also showed that there are significant differences between regions and subregions at %5 level. North had the highest and lowest cellulose and lignin contents respectively. These results also proved that P.australis is one of the best Iranians' raw materials as cellulose and lignin contents between the others.
