Management and Economics wood
Afshin Kshn dehghan; Habibalah Khademi eslam; Behzad Bazyar
Abstract
In this study, the influence of the fungus (Coriolus versicolor) on the durability of Horn beam (carpinus betulus) in natural state and treated with CCA (Copper/Chromium/Arsenic) was evaluated. CCA is a kind of water borne preservatives that was used to treat specimens under vacuum and pressure ...
Read More
In this study, the influence of the fungus (Coriolus versicolor) on the durability of Horn beam (carpinus betulus) in natural state and treated with CCA (Copper/Chromium/Arsenic) was evaluated. CCA is a kind of water borne preservatives that was used to treat specimens under vacuum and pressure (Bethel procedure) with amount of 3.5 & 1.5 percent on the basis of oven dry wood. Specimens were contaminated with cultured fungus for eight weeks in incubator. After this period, weight reduction, compressive strength (parallel to grain) and hardness of specimens were measured. Weight reduction of treated samples with 3.5 & 1.5 percent CCA were 1.68 and 1.73 percent respectively. Weight reduction of control samples were much higher (22.87 percent) than treated ones. There was no significant difference between the Compressive strength (parallel to grain) of treated and control samples without effect of fungus but the samples with effect of fungus have significant difference. Compressive strength (parallel to grain) of treated samples with 3.5 & 1.5 percent of CCA were 64.33 and 60.10 (Mpa) respectively but Compressive strength (parallel to grain) of control samples were much lower (38.44 Mpa) than treated samples. There was no significant difference between the hardness of treated and control samples without effect of fungus. On the other hand, the hardness of treated samples was more than control samples slightly, but this difference was not significant in 5 percent level. The hardness of treated and control samples with effect of fungus have significant difference. Hardness of treated samples with 3.5 & 1.5 percent of CCA were 5788(N) and 5799(N) respectively. However the hardness of control samples were much lower (3139N) than treated samples. Eventually CCA (Tanalith c) increased the durability of Horn beam (Carpinus betulus) from nondurable level to durable level.
Asghar Tarmian; Marjan Ebrahimi; Reza Oladi
Abstract
In this research, the effects of vessel features, including vessel diameter, density and porosity on drying rate and casehardening of beech (Fagus Orientalis) and oak (Quercus castaneifolia) was investigated. For this purpose, flat-sawn boards with dimensions of 170×50×80 mm (L×T×R) ...
Read More
In this research, the effects of vessel features, including vessel diameter, density and porosity on drying rate and casehardening of beech (Fagus Orientalis) and oak (Quercus castaneifolia) was investigated. For this purpose, flat-sawn boards with dimensions of 170×50×80 mm (L×T×R) were cut from the sapwood and were then dried in laboratory kiln at 50˚C and 50 % relative humidity to final moisture content of 8%. After drying, the severity of casehardening of dried boards was measured using prong test. For anatomical studies and measuring vessel features, white chalk and black marker method was used and scanned sections were analyzed using ImageJ. Pearson correlation was applied between vessel features and drying properties using SPSS software. Results showed that vessel proportion and porosity have more pronounced effect on the drying rate than vessel diameter and the latter feature can be ignored; as drying rate in the free-water domain was lower for oak having larger but fewer vessels than beech. Results also showed that correlation between casehardening and vessel diameter was significantly positive; however, a negative correlation was observed between porosity and casehardening.
Mehrabi Madhoshi; Maliheh Alizadeh
Abstract
In order to establish a kiln drying schedule for Iranian Beech (Fagus orientalis) lumbers of 5.5 cm thickness, commercially cut from Shast Kola region , 5 km distance from Gorgan. They were then dried under the program based on diffusion theory (from Malmquist's relations) were adopted to dry the lumbers ...
Read More
In order to establish a kiln drying schedule for Iranian Beech (Fagus orientalis) lumbers of 5.5 cm thickness, commercially cut from Shast Kola region , 5 km distance from Gorgan. They were then dried under the program based on diffusion theory (from Malmquist's relations) were adopted to dry the lumbers to the final moisture content of 12±2 %. This program for three separate kiln charges and initial moisture content 66.6, 58 and 45 percent was developed. Initial drying bulb temperature (first step) 46 °C and wet-bulb temperature 45 °C was calculated and in three schedules were same. The severity of surface, end checks and warp (bowing, crooking, twisting) in the lumbers were measured before and after the drying process and quality control methods were used to analyze the wood defects. Results indicated that drying of beech lumber using this new schedule was satisfactory. Also intensity changes of defect in all three repeats were about acceptable quality and quantity. Superior characteristics of this program was no surface checks in samples because the moisture content was reduced slowly.
asghar tarmian; Seaid Alireza Dehghan; Elnaz Trighnoor; Mohammad reza Pyramon; Razyeh Shamsy; Mohammad Layeghi
Abstract
In this research, the performance of a semi-greenhouse solar kiln was evaluated for dying different wood species in different season in Karaj. This study was carried out in two separate parts. In the first part, the flat-sawn boards of oak and fir with a nominal thickness of 50 mm were dried during summer ...
Read More
In this research, the performance of a semi-greenhouse solar kiln was evaluated for dying different wood species in different season in Karaj. This study was carried out in two separate parts. In the first part, the flat-sawn boards of oak and fir with a nominal thickness of 50 mm were dried during summer of the year 2012. In the second part, the flat-sawn boards of beech and poplar with the same thickness were dried in autumn, 2014 and spring, 2015. For both parts, the boards were also air-dried. The temperature measured inside the solar kiln was 35 ºC greater than that outside during daytime and also the kiln temperature ranged from 55 to 75ºC during 10 a.m. to 2 p.m.. In both parts of research, all wood species dried in the solar kiln faster with better quality compared to those air-dried. The severity of casehardening and surface checking in the boards dried in the solar kiln was lower and more homogenous moisture profile was observed. In addition, the final moisture content was lower for the boards dried in the solar kiln.
Zibab Frozan; asghar tarmian; Reza Ghamari; hamed matini behzad
Abstract
In this research, the effect of wetwood and blue stain on the drying rate and fluid transport coefficients of poplar (P. nigra) was evaluated. For this purpose, five boards with dimensions of 150 × 35 × 45 mm were cut from wet wood, normal wood and stained -wood areas of freshly cut ...
Read More
In this research, the effect of wetwood and blue stain on the drying rate and fluid transport coefficients of poplar (P. nigra) was evaluated. For this purpose, five boards with dimensions of 150 × 35 × 45 mm were cut from wet wood, normal wood and stained -wood areas of freshly cut lumbers in Taleghan region and then dried to the final moisture content of 8 percent inside a laboratory dryer at temperature of 50 °C, relative humidity of 60% and air velocity of 1 m/s. Overall, drying time was 120 h. After drying, the transverse permeability and diffusion coefficients were measured. The results showed that the wetwood had no decreasing effect on the drying rate of poplar wood; however, it reached to the final moisture content slower due to higher initial moisture content. َAlso, the wetwood had no significant effect on the transverse permeability but reduced the diffusion coefficient. In contrast to the wetwood effects, the drying rate, permeability and diffusion coefficients were increased due to the blue stain.
