@article { author = {Vaysi, Ramin and Salimifar, Mohammad reza}, title = {Investigation of Optical and Mechanical Properties of Bleached Chemi-mechanical Pulps (CMP) with Oxygen, Hydrogen Peroxide and Sodium Dithionite Stages}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {32}, number = {3}, pages = {311-321}, year = {2017}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2017.105625.1330}, abstract = {This study and it aim was accomplished on the effect of TCF bleaching on optical and mechanical properties of CMP pulp. For this purpose, some unbleached CMP pulps were randomly selected from Mazandaran Wood and Paper Industries (MWPI). Then these pulps were bleached with two and three OP, OPY, PY and O(Eo)P bleaching stages by using oxygen(O), alkali extraction with hydrogen peroxide(Eo), sodium dithionite(Y) . The hand sheets with 70 gr/m2 were prepared from above-mentioned of pulps, and then the optical and mechanical properties were measured and compared according by using TAPPI Standard test methods. The results showed that brightness, greenness, folds breaking length, tensile and tear strength were increased and opacity and a* factor were decreased. In general, role of three O(Eo)P stages and two OP and PY bleaching stages were better than P stage and unbleached CMP pulp mill in improve of brightness and its paper strength, too.}, keywords = {CMP pulp,Bleaching Stage,hydrogen peroxide,Oxygen,TCF Bleaching,Optical and mechanical properties}, title_fa = {بررسی ویژگی های نوری و مقاومتی خمیرکاغذ شیمیایی- مکانیکی(CMP ) رنگبری شده با توالی های اکسیژن، پروکسید هیدروژن و دی تیونیت سدیم}, abstract_fa = {این تحقیق با هدف تاثیر رنگبری کاملاً بدون کلر (TCF) بر ویژگی های نوری و مقاومتی کاغذ حاصل از خمیرکاغذCMP انجام شد. به همین منظور مقداری خمیر رنگبری نشده شیمیایی- مکانیکی((CMP به صورت تصادفی از کارخانه چوب و کاغذ مازندران انتخاب شد. سپس این خمیرها با توالی های دو و سه مرحله ای OP، OPY، PYو P(OE)O و با استفاده از اکسیژن(O)، پروکسید هیدروژن(P)،استخراج قلیایی با اکسیژن(OE) و دی تیونیت سدیم(Y) رنگبری گردید. از خمیرکاغذ های مذکور کاغذهای دست ساز با وزن پایه gr/m2 70 تهیه و خواص نوری و مقاومتی آن ها طبق آزمون های استاندارد TAPPI اندازه گیری و مقایسه گردید. نتایج نشان داد که در اثر رنگبری بدون ترکیبات کلر(TCF) روشنی، سبز رنگی، مقاومت های به پارگی، کششی، ترکیدن، طول پارگی و تاه شدن افزایش و ماتی و فاکتورa* کاغذ های حاصل از خمیرکاغذ CMP کاهش را نشان می دهد. به طور کلی، نقش توالی رنگبری سه مرحله ای P (Eo)O و همچنین توالی های رنگبری دو مرحله ای (PY) و (OP) در سفید سازی خمیرکاغذ CMP و بهبود روشنی و مقاومت های کاغذ حاصل موثر تر از توالی یک مرحله ای (P) و خمیر رنگبری نشده کارخانه بوده است.}, keywords_fa = {خمیر CMP,توالی رنگبری,پروکسید هیدروژن,رنگبری بدون ترکیبات کلر,خواص نوری و مقاومتی}, url = {https://ijwpr.areeo.ac.ir/article_112379.html}, eprint = {https://ijwpr.areeo.ac.ir/article_112379_2095c8d873c9932b14d36e1c78d6c4d2.pdf} } @article { author = {gholamian, Hadi and Tarmian, Asghar and Abdulkhani, Ali}, title = {Improvement of adhesion strength of polyurethane and alkyd coatings by nano-silane using sol-gel method}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {32}, number = {3}, pages = {322-333}, year = {2017}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2017.108093.1367}, abstract = {In present study, the adhesion strength of polyurethane and alkyd coatings on the poplar wood (Populus nigra) was improved by nano-silane coating using sol-gel method for outdoor application. For this purpose, the boards with dimensions of 15 × 10 × 2 mm were prepared according to EN 927-5. The surfaces of wood specimens were modified with Tetraethoxy‌silane (T) sol-gel material and then, solvent-borne alkyd (AS) and solvent-borne polyurethane (PS) coatings were applied. The coated samples were placed outdoor on a platform with a slope close to Karaj latitude (36̊) for 8 months according to ISO 877 standard. In order to characterize the quality of the coatings, colorimetric, tensile adhesion (Pull off), scratch adhesion (Cross cut) and ATR-FTIR tests were performed before and after weathering. The ATR-FTIR analysis demonstrated that the wood surface was covered with silicon oxides (SiO2) attached to hydrocarbon chains. As a result of surface wood modification by sol-gel, the color and adhesion strength of polyurethane and alkyd coatings were less affected by weathering. The highest tensile and scratch adhesions were found for the combined sol-gel and polyurethane coatings.}, keywords = {sol-gel,alkyd and polyurethane coating,Adhesion,weathering}, title_fa = {بهبود مقاومت چسبندگی پوشش‌های آلکیدی و پلی‌اورتان با استفاده از ترکیبات سیلانی به روش سل‌ژل‌}, abstract_fa = {در این تحقیق بهبود مقاومت چسبندگی پوشش‌های آلکیدی و پلی اورتان بر روی چوب صنوبر (Populus nigra) با استفاده از پوشش میانی نانو سیلانی به روش سل‌ژل برای کاربرد در فضای باز مورد ارزیابی قرار گرفت. برای این منظور نمونه‌هایی به ابعاد 2×10×15 میلیمتر مطابق با استاندارد 5-927 EN بریده شد. پس از اصلاح سطح نمونه‌ها با پوشش سل‌ژل تترا اتوکسی سیلان، پوشش‌های آلکیدی و پلی‌اورتان با دستگاه فیلم‌کش اعمال شد و نمونه‌های آماده شده به مدت 8 ماه مطابق استاندارد 877 ISO بر روی سکوی هوازدگی به طرف جنوب با شیب 36 درجه قرار داده شدند. کیفیت پوشش‌دهی با استفاده از آزمون‌های رنگ‌سنجی، چسبندگی کششی، چسبندگی خراشی و آزمون طیف‌سنجی مادون قرمز (FTIR-ATR) قبل و بعد از هوازدگی مورد بررسی قرار گرفت. نتایج مطالعات طیف‌سنجی نشان داد که نانو ذرات تشکیل شده در سطح چوب در اثر فرآیند سل‌ژل ماهیت سیلانی (2SiO) دارند و گروه‌های –OH سطح چوب با این گروه‌های سیلانی واکنش داده‌اند. اصلاح سطح چوب با فرایند سل‌ژل موجب شد تا مقاومت چسبندگی پوشش‌های آلکیدی و پلی‌اورتان کمتر تحت تاثیر هوازدگی قرار گرفته و ثبات رنگی پوشش‌ها افزایش یابد. بیشترین مقاومت چسبندگی کششی و خراشی مربوط به پوشش ترکیبی سل‌ژل و پلی-اورتان بود.}, keywords_fa = {سل‌ژل,پوشش,آلکیدی,پلی‌اورتان,چسبندگی,هوازدگی}, url = {https://ijwpr.areeo.ac.ir/article_112019.html}, eprint = {https://ijwpr.areeo.ac.ir/article_112019_de571784e836555ff309221eb976d2a3.pdf} } @article { author = {Nourbakhsh, Amir}, title = {Investigation of Multi walled Carbon Nanotube and Microcrystalline Cellulose on Mechanical, and Morphological Properties Wood Plastics Composites}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {32}, number = {3}, pages = {334-344}, year = {2017}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2017.22966.1261}, abstract = {In this research was to use the effects micro cellulose, and Multi walled Carbon Nanotube on the mechanical properties of wood plastics composites. This article presents the application of Multi walled Carbon Nanotube in order to evaluate and compare their suitability as reinforcement for thermoplastics. The effects of loading micro cellulose and Multi walled Carbon Nanotube content on the mechanical properties were also studied. The results showed that mechanical properties of the composites made with 50 micron cellulose and 1.5 and 2.5 % of Multi walled Carbon Nanotube were significantly superior to those of the lower length (20 micron) and control samples. Addition of Multi walled Carbon Nanotube could enhance the mechanical properties of the blends, due to the improvement of interface bond between the filler and matrix of wood plastics composites. The significant improvements in mechanical properties of the blends composites made with Multi walled Carbon Nanotube and micro cellulose were further supported by SEM and TEM micrographs.}, keywords = {Composite,MECHANICAL PROPERTIES,Micro- cellulose,Multi walled Carbon Nanotube}, title_fa = {بررسی استفاده از نانو لوله‌های کربنی چند جداره (MWCNTs) و ذرات میکرو کریستالین سلولز در تولید نانو چندسازه چوب- پلاستیک}, abstract_fa = {در این بررسی استفاده از نانو لوله های کربنی چند جداره و ذرات میکروکریستالین سلولز در ساخت نانو چندسازه چوب پلاستیک مورد توجه قرار گرفته است. اثرات اندازه ذرات میکرو کریستالین سلولز و نانو لوله کربنی چند جداره MWCNTs) ) بر خواص مکانیکی و ریخت شناسی نانو چندسازه چوب پلاستیک مطالعه شده است. در این بررسی استفاده از ذرات میکروکریستالین سلولز بهمراه آرد چوب در دو سطح 20 و 50 میکرون و درصد نانو لوله های کربنی چند جداره در سطح صفر ، 5/1 و 5/2 درصد چند سازه چوب پلاستیک مورد توجه قرار گرفت. نتایج نشان داده است که خواص مکانیکی در چندسازه با طول 50 میکرون ذرات نانو لوله کربنی در سطح 5/1 درصد نسبت به سایر تیمارها برتر بوده است. همچنین نتایج آزمایشات نشان دادکه استفاده از ذرات میکرو کریستالین سلولز باعث بهبود خواص حرارتی در جریان مخلوط‌سازی در فاز درون سطحی شده و سبب اتصال بهتر بین الیاف و ماتریس گردیده است. خواص مکانیکی نانو چند سازه با استفاده از عکسبرداری SEM و TEM مورد بررسی گرفته است.}, keywords_fa = {چندسازه,میکرو کریستالین سلولز,نانو لوله های کربنی,جفت‌کننده مالییکی,خواص مکانیکی}, url = {https://ijwpr.areeo.ac.ir/article_113094.html}, eprint = {https://ijwpr.areeo.ac.ir/article_113094_2440ed3b6dd60679015abf9452f28719.pdf} } @article { author = {abdolalizadeh, mahboob and azadi boyaghchi, mehrnaz and mohammadypour, mohammad and mohammadi achachluei, mohsen}, title = {The assessment of antifungal effect of Thiophanate-methyl on Paper destructive fungi and ‎its application in conservation paper works}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {32}, number = {3}, pages = {345-358}, year = {2017}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2017.113143}, abstract = {Paper works are more attacked by biological agents such as fungi, bacteria and insects due to its organic nature. In ‎archives, most of the biological destruction of paper is related to fungi. The importance of paper works ‎conservation has led to applying different methods to fungus removal. The chemical disinfection is of of the most ‎common disinfection methods. In this research, the application of Thiophanate methyl in paper destructive fungi ‎has been studied. Laboratory studies to evaluate the effects of Thiophanate methyl on paper and fungus include ‎accelerated ageing, the evaluation of effectiveness of antifungal Thiophanate methyl on fungi such as ‎Aspergillusniger, Aspergillusflavus and Penicilliurnsp and determination of antifungal stability after accelerated ‎ageing. Examination shows that Thiophanate methyl has successfully prevented spread of fungus in all density of ‎‏10‏‎, ‎‏50‏‎, ‎‏100,200‏‎ and ‎‏500‏‎ ppm. Aspergillus flavus fungus had a slight growth at ‎‏10‏‎ ppm, but no growth were ‎observed in other density. Aspergillusniger fungus had no growth capacity in density more than ‎‏100‏‎ ppm. ‎According to the results, treated papers are still able to control fungus growth after being in accelerated ageing ‎condition. In general, the results obtained by fungus growth halo and non-growth halo indicate that all fungi are ‎controllable in density of ‎‏200‏‎ ppm.‎}, keywords = {PAPER,Thiophanate methyl,fungus cultivation,ageing condition,conservation and restoration}, title_fa = {ارزیابی تأثیر ضد قارچی تیوفانات متیل بر قارچ‌های مخرب کاغذ و کاربرد آن در حفاظت آثار کاغذی}, abstract_fa = {آثار‎ ‎کاغذی به دلیل ماهیت آلی خود بیشتر موردحمله‌ی عوامل بیولوژیکی مثل قارچ‌ها، باکتری‌ها و حشرات قرار می‌گیرند. ‏در آرشیوها معمولاً بیشترین نوع تخریب بیولوژیکی کاغذ، به قارچ‌ها مربوط می‌شود. اهمیت حفاظت آثار کاغذی باعث شده تا ‏روش‌های متفاوتی در قارچ ‌زدایی این آثار بکار گرفته شود. روش ضدعفونی شیمیایی یکی از پرکاربردترین شیوه‌ی ضدعفونی ‏است. در این پژوهش کاربرد قارچ‌کش تیوفانات متیل بر قارچ‌های مخرب آثار کاغذی موردمطالعه قرارگرفته است. مطالعات ‏آزمایشگاهی انجام‌شده جهت بررسی تأثیرات تیوفانات متیل بر کاغذ و قارچ، شامل پیرسازی تسریعی کاغذ، بررسی میزان ‏تأثیرگذاری قارچ‌کش تیوفانات متیل بر قارچ‌های ‏Aspergillus niger، ‏Aspergillus flavus‏ و ‏Penicilliurn sp‏ و تعیین ‏میزان پایداری قارچ‌کش بعد از پیرسازی تسریعی است. بررسی‌ها نشان داد که تیوفانات متیل در تمامی غلظت‌های 10، 50، ‏‏100، 200 و ‏ppm‏500 به‌طور کامل از رشد قارچ ‏Penicilliurn sp‏ جلوگیری کرد. قارچ ‏Aspergillus flavus‏ تنها در ‏غلظت ‏ppm‏10 مقداری رشد داشت؛ اما در بقیه‌ی غلظت‌ها هیچ رشدی از این قارچ دیده نشد. قارچ ‏Aspergillus niger‏ ‏نیز در غلظت‌های بالای ‏ppm‏100 توانایی رشد نداشت. بر اساس نتایج، کاغذهای تیمار شده پس از قرار گیری در شرایط ‏پیرسازی تسریعی همچنان توانایی مهار رشد قارچ‌ها را دارد. به‌طورکلی، نتایج حاصل از هاله‌ی رشد و هاله‌ی عدم رشد، ‏نشانگر آن بود که در غلظت ‏ppm‏200 هر سه قارچ به‌طور کامل قابل‌کنترل هستند.‏}, keywords_fa = {کاغذ,تیوفانات متیل,کشت قارچ,پیرسازی تسریعی,حفاظت و مرمت}, url = {https://ijwpr.areeo.ac.ir/article_113532.html}, eprint = {https://ijwpr.areeo.ac.ir/article_113532_f21701f52a94b8ddf39bd3b35cd705ae.pdf} } @article { author = {Yahyavi, Mostafa and Khazaeyan, Abolghasem and Shakeri, Alireza}, title = {The use of black liquor and nano-graphene oxide in urea formaldehyde adhesive to improve the mechanical and physical properties of particleboard}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {32}, number = {3}, pages = {359-368}, year = {2017}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2017.109080.1381}, abstract = {Abstract The aim of this research is the possibility of using black liqour and nano Graphene oxide (GO) for making three-layer particle board. In this study, the amount of black liqour was as 0, 10, 20 and 30 percent and Graphene oxide was 0, 0.25 and 0.5 percent (based on oven dried weight of UF). Wood particles was pressed with using a laboratory hydraulic press. Mechanical and physical properties (modulus of rupture, modulus of elasticity, internal bonding, water absorption and thickness swelling after 2 and 24h soaking in water) of the produced boards were measured according to EN standards. The effect of each of the variables was studied on the properties and analyzed at 95 percent with using SPSS software and variance analysis factorial design. The results showed that increasing black liqour resulted in decreasing the modulus of rupture, modulus of elasticity and internal bonding. The results also indicated that water absorption and thickness swelling after 2 and 24h soaking in water increased with increased black liqour and Graphene oxide percent. The results show that increasing of nano ghraphen resulted in increasing modulus of rupture, modulus of elasticity and internal bonding.}, keywords = {Black liquor,Graphene oxide,PHYSICAL AND MECHANICAL PROPERTIES,PARTICLE BOARD}, title_fa = {بررسی استفاده از لیکورسیاه و نانو گرافن اکسید در چسب اوره فرمالدهید جهت بهبود خواص فیزیکی و مکانیکی تخته خرده چوب}, abstract_fa = {چکیده هدف از این پژوهش امکان استفاده از لیکورسیاه و نانوگرافن اکسید (GO) جهت ساخت تخته خرده چوب سه‌لایه بود که در سطح آزمایشگاهی بررسی ‌گردید. نسبت لیکورسیاه در ترکیب چسب در 4 سطح 0، 10 ،20 و 30 درصد و همچنین مقدار نانوگرافن اکسید در سه سطح 0، 25/0 و 5/0 درصد براساس وزن خشک چسب مصرفی بود. مقاومت‌های مکانیکی و فیزیکی تخته‌های تولید شده شامل مقاومت خمشی، مدول الاستیسیته، چسبندگی داخلی، واکشیدگی ضخامت و جذب آب پس از 2 و 24 ساعت غوطه‌وری در آب مطابق با استاندارد EN اندازه گیری شد. با استفاده از نرم افزار SPSS و روش آنالیز واریانس در قالب طرح آزمایش فاکتوریل تأثیر هر یک از عوامل متغیر بر خواص مورد مطالعه در سطح اطمینان 95 درصد مورد تجزیه و تحلیل قرار گرفت. نتایج آزمایش نشان داد که با افزایش لیکورسیاه مقاومت خمشی، مدول الاستیسیته و چسبندگی داخلی کاهش یافت، نتایج آزمون واکشیدگی ضخامت و جذب آب پس از 2 و 24 ساعت غوطه‌وری در آب نشان داد که با افزایش مقدار لیکورسیاه و نانوگرافن اکسید درصد واکشیدگی ضخامت و جذب آب افزایش یافته است. همچنین با افزایش درصد نانوگرافن اکسید مقاومت خمشی، مدول الاستیسیته و چسبندگی داخلی افزایش یافت.}, keywords_fa = {لیکور سیاه,نانوگرافن اکسید,خواص فیزیکی و مکانیکی,تخته خرده چوب}, url = {https://ijwpr.areeo.ac.ir/article_112020.html}, eprint = {https://ijwpr.areeo.ac.ir/article_112020_0b240cd7e20d47c4bc87c71f2061c0bd.pdf} } @article { author = {Abdolahi, Mehdi and Mosavian, Said amir and Varamsh, Akbar and Asadi, Amin}, title = {Qualitative Structural Characterization of Two Lignin Samples and Quantitative Determination of Hydroxyl and Methoxyl Functional Groups in Kraft Lignin via Acetylation}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {32}, number = {3}, pages = {369-381}, year = {2017}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2017.109402.1388}, abstract = {In this research, two types of lignin, i.e. one extracted from industrial waste water of the Iran wood and paper (choka) factory as black liquor and another provided from Aldrich company, were studied. Firstly, the lignin was precipitated from its black liquor by a dilute acid and was then purified by dissolving in tetrahydrofuran (THF). Lignin samples were characterized using Fourier transform infrared (FTIR) and proton nuclear magnetic resonance (1HNMR) spectroscopies. It was found from results that the Aldrich lignin has a structure similar with the lignosulfonate while lignin extracted from black liquor does not have a hydrophilic sulfonate group and has a Kraft lignin structure. Using acetylation of Kraft lignin and complementary characterization with 1HNMR spectroscopy, the ratio of hydroxyl functional groups to methoxy groups was calculated to be 1.11 to 1, and amount of the hydroxyl groups was calculated to be 5.91 mmol/g of acetylated lignin, where 53% of the hydroxyl groups is related to the aromatic hydroxyl groups. By having the molecular weight of the Kraft lignin which was obtained from the gel permeation chromatography (GPC) analysis of the acetylated Kraft lignin to be 1260 g/mol, average number of the hydroxyl groups per acetylated lignin chain was calculated to be 7.44.}, keywords = {LIGNIN,Acetylation,Structural characterization,FTIR,1H-NMR}, title_fa = {شناسایی کیفی ساختار دو نمونه لیگنین‌ و تعیین کمّی گروه های عاملی هیدروکسیل و متوکسیل لیگنین کرافت از طریق استیل دار کردن}, abstract_fa = {در این پژوهش، دو نمونه لیگنین، یکی استخراج شده از پساب صنعتی کارخانه چوب و کاغذ ایران (چوکا) تحت عنوان مایع سیاه و دیگری تهیه شده از شرکت آلدریچ، مطالعه شدند. لیگنین ابتدا از مایع سیاه آن توسط اسید رقیق رسوب داده شده و سپس با انحلال در تتراهیدروفوران خالص‌سازی شد. ساختار کلی نمونه‌های لیگنین با استفاده از آزمون‌های طیف‌سنجی مادون قرمز تبدیل فوریه (FTIR) و تشدید مغناطیسی هسته پروتون (1HNMR) شناسایی شدند. نتایج نشان داد که لیگنین تهیه شده از شرکت آلدریچ ساختاری مشابه با لیگنوسولفونات دارد، در حالی که لیگنین استخراج شده از مایع سیاه فاقد گروه‌های سولفوناتی بوده و از نوع لیگنین کرافت می‌باشد. با استفاده از واکنش‌ استیل‌دار کردن لیگنین کرافت و شناسایی تکمیلی با طیف‌سنجی تشدید مغناطیسی هسته پروتون (1HNMR)، نسبت تعداد گروه‌های عاملی هیدروکسیل به متوکسی 11/1 به 1 و تعداد گروه‌های هیدروکسیل آن به طور متوسط 91/5 میلی مول بر گرم لیگنین استیل‌دار محاسبه شد؛ که 53% آن به گروه‌های هیدروکسیل آروماتیکی مربوط بود. با داشتن وزن مولکولی لیگنین استیل‌دار شده که از آزمون کروماتوگرافی ژل تراوایی برابر1260 گرم بر مول بدست آمد، تعداد متوسط گروه‌های عاملی هیدروکسیل به ازای هر زنجیر لیگنین کرافت استیل دار شده محاسبه و مقدار 44/7 بدست آمد.}, keywords_fa = {لیگنین,استیل‌دار کردن,شناسایی ساختار,FTIR,طیف سنجی مغناطیسی هسته پروتون (1HNMR)}, url = {https://ijwpr.areeo.ac.ir/article_113508.html}, eprint = {https://ijwpr.areeo.ac.ir/article_113508_944380991fe46b4445912a34eef84641.pdf} } @article { author = {OMRANI, PANTEA and Eisapor, Reza}, title = {Investigation and compare the tensile strength of hardwood dowel joints, made by glue and welding}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {32}, number = {3}, pages = {382-391}, year = {2017}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2017.109986.1398}, abstract = {The insertion of dowels into solid wood for furniture has been used for centuries. Recently, this simple technology has been upgraded. The objective of the research was to evaluate and compare the tensile strength of the joints made of wood dowel through new method “wood welding” and classical method “using of glue”. Variables included dowel joints method (welding joint and joint with glue), dowel diameter (10 and 12 mm) and dowel surface (smooth and grooved). Members joint and dowel wood were hornbeam species (Carpinus betulus) and the used glue was polyvinyl acetate (PVA). The results showed that the types of joints, diameter and surface dowel, have significant effect on the tensile strength, so that welded joints, dowel diameter 12 mm and dowel grooved surface has the most tensile strength to other samples. The results also showed that in all cases, the strengths of the joints made by welding was more than the joints made by PVA glue.}, keywords = {wood welding,dowel joint,the tensile strength of the joint,polyvinyl acetate,Carpinus betulus}, title_fa = {بررسی و مقایسه مقاومت کششی اتصالات دوبل چوب پهن‌برگ، ساخته شده به دو روش اتصال با چسب و جوشکاری}, abstract_fa = {گنجاندن دوبل‌ها در چوب ماسیو برای ساخت مبلمان، برای قرن‌ها مورد استفاده بوده است و به تازگی این تکنیک ساده به تکنولوژی جوشکاری چوب ارتقاء یافته است. هدف از پژوهش حاضر، بررسی و مقایسه مقاومت کششی اتصالات ساخته شده با دوبل چوبی به روش نوین جوشکاری و روش مرسوم استفاده از چسب می‌باشد. متغیرهای مورد بررسی، روش اتصال دوبل (اتصال جوشکاری شده و اتصال با چسب)، قطر دوبل (10 و 12 میلی‌متر) و شکل سطح دوبل (صاف و شیاردار) در نظر گرفته شد. اعضای اتصال و دوبل از گونه‌ی پهن‌برگ ممرز (Carpinus betulus) و چسب مصرفی پلی وینیل استات (PVA) انتخاب گردید . نتایج نشان دادند که نوع اتصال، قطر و سطح دوبل بر مقاومت کششی اثر معنی‌داری دارد؛ به‌طوری‌که اتصالات جوشکاری شده، دوبل با قطر mm 12 و دوبل با سطح شیاردار دارای بیشترین مقاومت کششی نسبت به سایر نمونه‌ها بودند. همچنین نتایج نشان داد که در تمام حالت‌ها، مقاومت‌های مربوط به اتصالات ساخته شده توسط روش جوشکاری، نسبت به اتصالات ساخته شده توسط چسب PVA بیشتر بود.}, keywords_fa = {جوشکاری چوب,اتصال دوبل,مقاومت کششی اتصال,پلی وینیل استات,گونه‌ی ممرز}, url = {https://ijwpr.areeo.ac.ir/article_112382.html}, eprint = {https://ijwpr.areeo.ac.ir/article_112382_cc91c29a2b74b076e9ca884de1241997.pdf} } @article { author = {Ghorbani, Maryam and null, null and fooladian, farhad}, title = {Effect of thermal modification on physical and mechanical behavior of sunflower-polypropylene composites}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {32}, number = {3}, pages = {392-401}, year = {2017}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2017.110664.1414}, abstract = {The Use of agricultural plants wastes as an alternative forest resources in the cellulose industry can be recommended due to the severe shortage of wood raw material and restriction of forest harvesting. The aim of current research was to investigate the effect of thermal modification on applied properties of composite made from sunflower stem flour-polypropylene. Thermal modification of sunflower stems was done at temperatures of 160, 180 and 200°C for 30 minutes and mixed with polypropylene in ratio of 30wt%. Test samples were prepared with maleic anhydride-grafted polypropylene as coupling agent by injection molding method. FTIR spectroscopy of sunflower stem flour confirmed the chemically changes due to thermal modification. More integration and uniform distribution, and less cavities were observed in the scanning electron micrographs of failure surface. The removal of hemicellulose of sunflower stem flour improved the thermal stability of composite, which thermal gravimetric analyzer (TGA) confirmed it with increasing in modification temperature up to 180°C. Modification at 200°C decreased thermal stability compared to other temperatures. Thermal modification leads to significant decrease in water absorption and improvement in bending and tensile properties due to hemicellulose degradation, increasing the crystallinity, loss of polarity, increased compatibility between the two phases of composite and uniform distribution of fillers in polymeric matrix. Notched impact strength of modified composites decreased due to better adhesion between lignocellulosic filler and polymer that facilitate the crack development along the interface.}, keywords = {Thermal modification,sunflower-polypropylene composites,Thermal stability,physical properties,mechanical behavior}, title_fa = {اثر اصلاح گرمایی بر رفتار فیزیکی و مکانیکی فرآورده مرکب آفتابگردان/پلی‌پروپیلن}, abstract_fa = {با کمبود شدید ماده‌اولیه چوبی و محدودتر شدن بهره‌برداری از جنگل‌ها، کاربرد پسماند گیاهان کشاورزی ‌به عنوان جایگزین منابع جنگلی در صنایع سلولزی را می‌توان توصیه نمود. هدف از تحقیق حاضر بررسی اثر ‌اصلاح گرمایی ساقه آفتابگردان بر خواص کاربردی فرآورده مرکب آرد ساقه آفتابگردان/پلی‌پروپیلن بوده‌است. اصلاح گرمایی ساقه آفتابگردان در 3 سطح دمایی 160، 180 و 200 درجه‌سانتی‌گراد در زمان 30 دقیقه انجام شد چندسازه با اختلاط 30 درصد وزنی آرد ساقه آفتابگردان با پلی‌پروپیلن در حضور انیدریدمالئیک پیوند شده به پلی‌پروپیلن به عنوان عامل جفت‌کننده و به روش قالب‌گیری تزریقی تهیه گردید. نتایج طیف‌سنجی آرد ساقه‌آفتابگردان تغییرات شیمیایی ناشی از اصلاح گرمایی را تایید کرد. در تصاویر میکروسکوپ الکترونی یکپارچگی بیشتر، توزیع یکنواخت‌تر و حفره‌های کمتر در سطح شکست فرآورده‌های حاوی آرد اصلاح گرمایی شده مشاهده گردید. بر اساس تحلیل وزن‌سنجی گرمایی، حذف همی‌سلولزها باعث بهبود پایداری گرمایی ماده مرکب تا دمای 180 درجه‌سانتی‌گراد را نشان داد، ولیکن افزایش دمای اصلاح به 200 درجه‌سانتی‌گراد موجب کاهش پایداری گرمایی فرآورده حاصل شد. ‌اصلاح گرمایی با تخریب همی‌سلولزها، افزایش بلورینگی، کاهش قطبیت، افزایش سازگاری بین دو فاز چندسازه، و توزیع یکنواخت پرکننده در زمینه پلیمر منجر به کاهش جذب آب و بهبود معنی‌دار خواص خمشی و کششی شد. چسبندگی خوب پرکننده لیگنوسلولزی و پلیمر با تسهیل انتشار ترک در امتداد ناحیه سطح مشترک، موجب کاهش مقاومت به ضربه فاق‌دار فرآورده حاصل گردید.}, keywords_fa = {اصلاح گرمایی,فرآورده مرکب آفتابگردان/پلی‌پروپیلن,پایداری گرمایی,خواص فیزیکی,رفتار مکانیکی}, url = {https://ijwpr.areeo.ac.ir/article_112384.html}, eprint = {https://ijwpr.areeo.ac.ir/article_112384_e30ee22aee19367119c1e4fb508d10b4.pdf} } @article { author = {Zafari sarmori, Mohammad and Farokhpayam, saeid reza and Sanei, Ehsan and shamsian, mohammad}, title = {The effects of recycling on the physical and mechanical properties of wood plastitc composite made with high density polyethylene}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {32}, number = {3}, pages = {402-410}, year = {2017}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2017.107141.1356}, abstract = {Although many studies have been done about the application of waste materials such as used plastics but returning of wood plastic products (Regrind) to the production cycle was rarely reported. In this work, the effect of once and twice regrind on the functional properties of WPC made from high density polyethylene (HDPE) has been studied. The specimens were fabricated with powder raw materials and by the flat press under laboratory conditions. HDEP and poplar wood flour were mixed with a weight ratio of 50-50 percent. The estimation of regrind process, physical and mechanical properties of boards were measured after each regrinding and also to evaluate of regrinding on filler particle size and the interface between the polymer and wood flour some Scanning Electron Microscopy (SEM) were prepared. The results of this research showed that regrinding of WPC leads to a decrease in mechanical properties including bending strength, flexural modulus, tensile strength and tensile modulus and on the other hand regrinding process leads to improved physical properties including water absorption and thickness swelling after hours. SEM photographs showed that during the process of regrinding, filler particle size is reduced while matrix surrounding the filler particles better.}, keywords = {Regrind,wood plastitc composite,PHYSICAL AND MECHANICAL PROPERTIES,matrix,filler}, title_fa = {تأثیر بازآسیاب بر خصوصیات فیزیکی و مکانیکی فرآورده مرکب چوب پلاستیک ساخته‌شده با پلی‌اتیلن سنگین}, abstract_fa = {درباره‌ی استفاده از مواد ضایعاتی مانند پلاستیک‌های دست‌دوم، تحقیقات زیادی به چشم می‌خورد اما به بازگشت فرآورده‌ی کامل چوب پلاستیک (بازآسیاب) به چرخه‌ی تولید کمتر پرداخته‌شده است؛ بنابراین، این کار پژوهشی تمرکز خود را بر روی تأثیر بازآسیاب یک‌باره و دوباره بر خواص کاربردی فرآورده چوب پلاستیک پلی‌اتیلنی سنگین قرار داده است. نمونه‌ها به روش پرس تخت، با مواد اولیه به شکل پودر و تحت شرایط آزمایشگاهی ساخته شدند. برای ساخت نمونه‌ها از پلی‌اتیلن سنگین و آرد چوب صنوبر با درصد وزنی 50-50 استفاده شد. برای برآورد اثر بازآسیاب، خصوصیات فیزیکی و مکانیکی تخته‌های ساخته‌شده پس از هر بار بازآسیاب اندازه‌گیری شد و برای برآورد اثر بازآسیاب بر روی اندازه ذرات پرکننده و همچنین فصل مشترک بین آرد چوب و پلیمر تصاویر میکروسکوپ الکترونی (SEM) تهیه گردید. نتایج حاصل از این کار پژوهشی نشان داد که بازآسیاب چوب پلاستیک منجر به کاهش خواص مکانیکی شامل مقاومت خمشی، مدول خمشی، مقاومت کششی و مدول کششی می‌شود و همچنین فرآیند بازآسیاب منجر به بهبود خواص فیزیکی شامل جذب آب 24 ساعت و واکشیدگی ضخامت 24 ساعت می‌شود. تصاویر میکروسکوپی نشان داد که در خلال فرآیند بازآسیاب اندازه ذرات پرکننده کاهش پیداکرده است و ماتریس، ماده پرکننده را به‌صورت بهتری در برگرفته است.}, keywords_fa = {بازآسیاب,فرآورده مرکب چوب پلاستیک,خواص مکانیکی,ماده‌ی زمینه,پرکننده}, url = {https://ijwpr.areeo.ac.ir/article_113052.html}, eprint = {https://ijwpr.areeo.ac.ir/article_113052_074c49837108e0d6f1c96aea047d845f.pdf} } @article { author = {Samariha, Ahmad and Khademi Eslam, Habibollah}, title = {The effect of water vapor treatment of wood flour on physical and mechanical properties of hybrid composite made of poplar fiber and recycled polypropylene}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {32}, number = {3}, pages = {411-421}, year = {2017}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2017.108571.1372}, abstract = {Abstract The effect of adding steamed and non-steamed fiber on physical and mechanical properties of the composites made of recycled polypropylene was investigated. Recycled polypropylene was used as a basic matrix at a 57% level, and poplar fibers were used at 180 °C for 1 h at a constant level of 40% in two forms: non-steamed and steamed. The ratio of steamed fibers to non-steamed fibers in composites was 100:0, 50:50, and 0:100, respectively. For all components, the coupling agent was maleic anhydride at a level of 3%. Mixing was done using an internal mixer at 180 °C and 60 rpm, and the samples were constructed by injection molding method. To investigate the effect of steam treatment on the fiber structure and crystallization, X-ray diffraction analysis and FTIR spectra were used. The results showed that the Steaming had no significant effect on resistance. But with steaming increased mechanical properties and physical properties of reduced. Keywords: Composites, Recycled polypropylene, Steamed fiber, XRD, FTIR}, keywords = {composites,Recycled polypropylene,Steamed fiber,XRD,FTIR}, title_fa = {بررسی اثر تیمار بخارآب آرد چوب بر خواص فیزیکی، مکانیکی چندسازه ساخته‌شده از آرد صنوبر و پلی‌پروپیلن بازیافتی}, abstract_fa = {چکیده اثر افزودن آرد تیمار شده و نشده با بخارآب بر خواص فیزیکی و مکانیکی چندسازه ساخته‌شده از پلی‌پروپیلن بازیافتی بررسی شد. پلی‌پروپیلن بازیافتی در سطح ۵۷ درصد وزنی و آرد صنوبر به‌میزان ثابت ۴۰ درصد به دو صورت بخاردهی نشده و بخار دهی شده تحت دمای 180 درجه سانتی‌گراد به مدت یک‌ساعت استفاده شدند. نسبت آرد بخاردهی شده به نشده در چندسازه‌ها به-ترتیب 100:0، 50:50 و 0:100 در نظر گرفته شد. در کلیه ترکیبات ماده سازگارکننده به‌میزان 3 درصد وزنی استفاده شد. عمل اختلاط در مخلوط‌کن داخلی، با دمای 180 درجه سانتی‌گراد و با سرعت 60 دور در دقیقه انجام شد و نمونه‌ها با روش قالبگیری تزریقی ساخته شدند. به‌منظور بررسی اثر بخاردهی آرد چوب بر ساختار و بلورینگی، از آزمون تفرق اشعه X و طیف FTIR استفاده شد. نتایج نشان داد بخاردهی آرد چوب، به لحاظ آماری تأثیر معنی‌داری بر ویژگی‌های مکانیکی چند سازه حاصل ندارد، ولی نمونه‌های حاوی آرد بخاردهی شده از مقاومت‌های مکانیکی به نسبت بالاتری برخوردار بودند. همچنین نتایج نشان داد که تاثیر بخار دهی بر جذب آب و واکشیدگی ضخامت معنادار بوده و نمونه‌های بخاردهی شده خواص فیزیکی بهتری داشته‌اند.}, keywords_fa = {چندسازه,پلی‌پروپیلن بازیافتی,آرد بخاردهی شده,XRD,FTIR}, url = {https://ijwpr.areeo.ac.ir/article_113053.html}, eprint = {https://ijwpr.areeo.ac.ir/article_113053_4b3fe39fc525a00e13297dc73e75e1f2.pdf} } @article { author = {Nazari, Latif and Hosseinihashemi, Seyyed Khalil}, title = {Laboratory Study of Synergistic Effects of Mixtures of Organic Biocides, Metal Chelator and Antioxidant Materials against Rainbow White-rot Fungus}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {32}, number = {3}, pages = {422-435}, year = {2017}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2017.114464.1424}, abstract = {In this research, the individual and interaction effects of three organic biocides (propiconazole, tebuconazole, and chlorothalonile) with the metal chelator EDTA and the antioxidant BHT at different concentrations (50, 150, 250, 350, and 450 ppm) against the white-rot fungus, Trametes versicolor was investigated. In under laminar sterile hood, about 25 mL of the media was poured into the Petri plates. Three antibiogram discs (with triangular position) put on the media. By micro-sampler about 20 μL of steriled preservative solutions was poured on every disc, separately. Then, about 5 mm of mycelium plug of intended fungus that was inoculated previously was put in the center of plates. The plates were incubated and daily for one week, the mycelium growth of fungus and inhibition effects of different preservative solutions against fungus was measured. The results of this research demonstrated that chlorothalonil biocide by itself have not any inhibition effect on growth of fungus, whilst propiconazole and tebuconazole biocides by itself have significant effect at different concentrations on growth of fungus. In consider of synergistic effect of propiconazole, tebuconazole, and chlorothalonil biocides with non-biocides additives of EDTA and BHT, it has been found that there is synergistic effect between propiconazole biocide and the metal chelator EDTA at high concentration such as 450 ppm, but in combination with other solutions synergistic effect has not been found. Also, any synergistic effect has not found between tebuconazole and chlorothalonil biocides with other preservative solutions.}, keywords = {Organic biocides,EDTA,BHT,growth inhibition,Synergism,TRAMETES VERSICOLOR}, title_fa = {بررسی آزمایشگاهی اثرات هم افزایی (سینرژیک) مخلوط های آفت کش های آلی، مواد کیلیت کننده فلز و آنتی اکسیدان در برابر قارچ مولد پوسیدگی سفید رنگین کمان}, abstract_fa = {در این تحقیق اثرات مستقل و متقابل آفت کش های آلی پروپیکونازول، تبوکونازول و کلروتالونیل با کیلیت کننده فلز اتیلن دی آمین تترا استیک اسید (EDTA) و آنتی اکسیدان هیدروکسی تولوئن بوتیل دار (BHT) در غلظت های مختلف 50، 150، 250، 350 و ppm 450 در برابر قارچ مولد پوسیدگی سفید رنگین کمان (Trametes versicolor) مورد آزمون قرار گرفت. در زیر هود لامینار، به میزان 25 میلی لیتر از محیط کشت استریل در داخل پتریدیش ها ریخته شد. سه دیسک آنتی بیوگرام استریل (با موقعیت مثلثی شکل) روی محیط کشت قرار داده شد. به کمک نمونه بردار به میزان 20 میکرولیتر محلول حفاظتی استریل شده بر روی هر یک از دیسک ها به طور جداگانه ریخته شد. سپس به مقدار 5 میلی متر از پلاگ میسیلیوم قارچ در مرکز پتریدیش ها قرار داده شد. پتریدیش ها به مدت یک هفته در داخل انکوباتور قرار داده شدند. روزانه به مدت یک هفته، رشد میسیلیوم قارچ و اثرات بازدارندگی محلول های حفاظتی مختلف در برابر قارچ، مورد اندازه گیری قرار گرفت. نتایج حاصل از این تحقیق نشان داد که آفت کش کلروتالونیل به تنهایی هیچ اثر بازدارندگی بر روی رشد قارچ نداشته است، در حالی که آفت کش های پروپیکونازول و تبوکونازول به تنهایی اثر معنی داری در غلظت های مختلف بر روی رشد قارچ داشته اند. در بررسی اثر هم افزایی (سینرژیک) آفت کش های پروپیکونازول، تبوکونازول و کلروتالونیل با افزودنی های غیر آفت کش EDTA و BHT این طور یافته شده است که بین آفت کش پروپیکونازول و کیلیت کننده فلز EDTA در غلظت بالا مانند ppm 450 اثر هم افزایی وجود داشته است، اما در ترکیب با بقیه محلول ها، اثر هم افزایی یافته نشده است. همچنین، هیچگونه اثر هم افزایی بین آفت کش های تبوکونازول و کلروتالونیل با سایر محلول های حفاظتی یافته نشده است.}, keywords_fa = {آفت کش های آلی,BHT,EDTA,بازدارندگی رشد,هم افزایی,قارچ رنگین کمان}, url = {https://ijwpr.areeo.ac.ir/article_113054.html}, eprint = {https://ijwpr.areeo.ac.ir/article_113054_ca00610ad0b01b6b4ca9a673d33ad885.pdf} } @article { author = {Rezvani, Mohammad Hadi and Talaei, Aisona and Rajabi Cham Heidari, Hosseinali}, title = {Modification of Paulownia Wood with methylolated dimethyloldihydroxyethylenurea (mDMDHEU) and the investigation of its effect on Some of Strength Properties}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {32}, number = {3}, pages = {436-449}, year = {2017}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2017.110668.1415}, abstract = {One of the main strategies to develop the extent of wood modification is using active functional groups in wood structure or the so-called impregnation with modified N-methylol compound. The aim of this study was to evaluate the physical properties of paulownia wood after modify with Polycrease ECR Cell wall resin, to name modified dimethylol-dihydroxyethyleneurea (mDMDHEU). Physical test samples were prepared according to ASTM and EN standard and treated with pressure vessel method at two concentration levels; 15 and 25 percent of soluble resin. For polymerization, treated samples were heated in oven for 24-hour periods at 145 and 155 ºC respectively. Weight percent gain (WPG), bulking, water soaking, swelling, anti-swelling efficiency (ASE), leaching and contact angle were determined. High mDMDHEU concentration increased the weight gain and cell wall bulking. Highest weight percent gain (10.70%) and bulking efficiency (6.85%) in to levels of 25% were determined at 155 ˚C. In comparison with the unmodified wood, the mDMDHEU modified wood due to absorbed polymer enhancement exhibited improved dimensional stability and reduced water uptake, and maximum dimensional stability were determined in samples modified using to level 25% mDMDHEU containing solutions and curing temperature 155 ºC. Moreover, mDMDHEU treatment was resistant to leaching. Contact angle measurement further confirmed the improved hydrophobicity of wood after modification. Modification with mDMDHEU improved significantly the physical properties. The improve of the resistance of chemically modified wood exposed to can be attributed to the reduction of wood moisture, bulking of cell walls and cell cavities blocking affect to dominant reactivity mDMDHEU with cell wall wood polymer.}, keywords = {physical properties,Polycrease ECR (mDMDHEU),Cell Wall WPC,water absorption,bulking efficiency}, title_fa = {اصلاح چوب پالونیا بادی ‌متیلول دی هیدروکسی اتیلن‌‌اوره اصلاح‌شده (mDMDHEU) و بررسی تأثیر آن بر برخی ویژگی‌های فیزیکی}, abstract_fa = {یکی از راه‌کارهای مهم افزایش گستره کاربرد اصلاح خواص چوب، بهرهگیری از گروه‌های عاملی فعال در ساختار چوب یا به اصطلاح آغشته ‌کردن با ترکیبات N- متیلول است. هدف از این تحقیق، بررسی ویژگی‌های فیزیکی چوب پالونیا پس از اصلاح با رزین دیواره‌ای Polycrease ECR، به‌ نام‌ دی متیلول دی هیدروکسی اتیلن‌ اوره اصلاح‌ شده (mDMDHEU) بود. نمونه‌های آزمون فیزیکی بر اساس استاندارد ASTM و EN تهیه گردیدند و به ‌روش سلول تهی اصلاح ‌شده در دو سطح غلظت 15 و 25 درصد از رزین اشباع شدند. پلیمریزاسیون رزین تحت اعمال دما در آون در بازه زمانی 24 ساعت، به‌ترتیب در دو سطح دمای 145 و 155 درجه سانتی‌گراد انجام شد. درصد افزایش وزن، تورم حجمی، جذب آب، واکشیدگی‌ حجمی، اثر ضد واکشیدگی، آبشویی و زاویه تماس اندازه‌گیری شد. افزایش سطح غلظت mDMDHEU، به افزایش وزن و حجیم‌شدگی دیواره سلولی چوب منتهی شد. بیشترین درصد افزایش وزن (70/10 درصد) و ضریب حجیم‌شدگی (85/6 درصد) در سطح 25 درصد mDMDHEU، و دمای 145 درجه سانتی‌گراد تعیین شد. در مقایسه با چوب اصلاح نشده، ثبات ابعاد چوب اصلاح شده با mDMDHEU، در اثر افزایش سطح جذب پلیمر، بهبود یافته و جذب آب کاهش داشته است، به‌طوری‌که بیشترین پایداری ابعاد در سطح حاوی 25 درصد mDMDHEU، و دمای 145 درجه سانتی‌گراد اندازه‌گیری شد. به‌علاوه تیمار mDMDHEU، به آبشویی مقاوم بود. اندازه‌گیری زاویه تماس، بهبود آب‌گریزی چوب پس از اصلاح را تأیید کرد. اصلاح با mDMDHEU، بهبود معنی‌دار خواص فیزیکی را به‌همراه داشت. بهبود مقاومت فیزیکی چوب اصلاح شیمیایی شده را می‌توان به‌کاهش رطوبت، حجیم‌شدن دیواره سلولی و مسدود شدن منافذ در اثر واکنش‌پذیری بالای mDMDHEU، با پلیمر دیواره سلول چوب نسبت داد.}, keywords_fa = {ویژگی های فیزیکی,(Polycrease ECR (mDMDHEU,چوب پلیمر دیواره‌ای,جذب آب,ضریب حجیم کنندگی}, url = {https://ijwpr.areeo.ac.ir/article_112021.html}, eprint = {https://ijwpr.areeo.ac.ir/article_112021_1ccaa1d85becba8371f23a81ab123b94.pdf} } @article { author = {Golbabaei, Fardad and Nourbakhsh, Amir and Kargarfard, Abolfazl and Hajihassani, Reza}, title = {Investigation on the Properties of Cement Fiber Board Produced Using Waste Paper}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {32}, number = {3}, pages = {450-461}, year = {2017}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2017.110393.1404}, abstract = {In this study, the reinforcing effect of recycled newsprint paper (RNP) in cement boards has been investigated. The experiment was designed to apply two variable factors, RNP and calcium chloride (CaCl2). Cement-fiber boards with the density of 0.7 kg/m3 were manufactured using fiber/cement ratios of 10:90, 15:85, 20:80 and 25:75 (w/w) and 3% and 5% CaCl2 as accelerator. Minimum four boards (replications) were fabricated for each combination of variables, and the mechanical and physical properties of the boards were evaluated. The statistical analysis showed that the effect of the RNP and CaCl2 contents on modulus of rupture of cement fiber boards were significant at 1% significant level. The results showed that addition of CaCl2 enhanced the mechanical properties of the boards. All properties of the boards were improved as the CaCl2 content was increased from 3% to 5%. The modulus of rupture and modulus of elasticity of the boards decreased with addition of RNP, and the maximum values were obtained at RNP loading of 10%. The results also showed that as the fiber content was increased, significant increase in water absorption and thickness swelling occurred. Increasing RNP fiber content from 10% to 25% reduced both the mechanical and physical properties considerably. The optimum condition was obtained when the RNP and CaCl2 contents were 10% and 5%, respectively.}, keywords = {Fiber cement,waste paper,calcium chloride,Composite}, title_fa = {امکان استفاده از روزنامه باطله در تولید آجر الیاف سیمان سبک}, abstract_fa = {در این تحقیق نقش تقویت الیاف روزنامه باطله در ساخت تخته‌سیمان مورد بررسی قرار گرفته است. این بررسی برای اعمال دو عامل متغیر یعنی الیاف روزنامه باطله و کلرید کلسیم طراحی شده است. تخته الیاف سیمان با دانسیته 7/0 کیلوگرم بر مترمکعب با استفاده از نسبت‌های الیاف/سیمان 90:10، 15/85، 20/80 و 25/75 و کلرید کلسیم با 3% و 5% به‌عنوان شتاب‌دهنده تولید و مورد بررسی قرار گرفت. تخته‌ها حداقل در چهار تکرار برای هر ترکیب از متغیرها ساخته شده و خواص مکانیکی و فیزیکی آنها مورد ارزیابی قرار گرفت. تجزیه‌وتحلیل آماری نشان داد که اثر مقدار الیاف روزنامه باطله و مقدار کلرید کلسیم در مدول گسیختگی و واکشیدگی در 24 ساعت تخته الیاف سیمان‌های تولید شده در سطح 1% معنی‌دار بوده است. نتایج نشان داد که با افزایش مقدار کلریدکلسیم مقاومت به خمش استاتیک افزایش و واکشیدگی ضخامت کاهش می‌یابد. تمام خواص تخته الیاف سیمان‌ها با تغییر مقدار کلرید کلسیم از 3% به 5% بهبود یافته است. مدول گسیختگی و مدول‌الاستیسیته تخته‌ها با افزایش مقدار درصد الیاف روزنامه باطله کاهش می‌یابد و حداکثر مقدار آن در استفاده از 10% الیاف روزنامه باطله به‌دست‌آمده است. همچنین نتایج نشان داد که با افزایش میزان الیاف روزنامه باطله افزایش قابل‌توجهی در جذب آب و واکشیدگی الیاف در ضخامت رخ می‌دهد. افزایش میزان الیاف روزنامه باطله از 10% به 25% خواص مقئمت به خمش را کاهش و واکشیدگی ضخامتی را به میزان قابل‌توجهی افزایش می‌دهد. با بررسی‌ نتایج به‌دست‌آمده مطلوب‌ترین شرایط هنگامی به دست می‌آید که مقدار الیاف روزنامه باطله و کلرید کلسیم به ترتیب 10% و 5% باشد. }, keywords_fa = {الیاف چوب سیمان,روزنامه باطله,اتصال معدنی,کامپوزیت}, url = {https://ijwpr.areeo.ac.ir/article_113092.html}, eprint = {https://ijwpr.areeo.ac.ir/article_113092_64f768c5edb86953e628e52cb8b2c19d.pdf} }