@article { author = {Kargarfard, Abolfazl}, title = {Investigation on Utilization of Corn stalk In Particleboard Production}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {25}, number = {2}, pages = {147-156}, year = {2010}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2010.117277}, abstract = {The of utilization corn stalk residues in combination with poplar wood for particleboard production is investigated. Four combinations of corn stalk and P.nigra particles (100% corn stalk; 75% corn stalk, 25% poplar wood; 50% corn stalk, 50% poplar wood and 25% corn stalk, 75% poplar wood) is used. Two resin contents of 10 and 12% and two press temperatures of 170 and 180C is employed. The results showed that increasing press temperature from 170 to 180C, decreased both MOR and MOE of boards and increasing resin content from 10 to 12%, improved MOR. When the ratio of poplar wood to corn stalk increases, both MOR and MOE of the boards increases and the highest values were reached at 50 and 75% poplar wood. Higher press temperature and lower ratio of corn stalk improved internal bond (IB). Higher press temperature, resin content and lower ratio of corn stalk, decreased thickness swelling. Based on the results, with application of either 25 to 50% corn stalk and press temperature of 170C, standard particleboard can be produced.  }, keywords = {}, title_fa = {اثراستفاده از ذرات ساقه ذرت بر ویژگیهای فیزیکی و مکانیکی تخته‌خرده‌چوب}, abstract_fa = {هدف از این تحقیق، کاربرد ساقه ذرت دانه‌ای در تولید تخته‌خرده‌چوب بوده است. لذا از مخلوط ساقه ذرت و چوب صنوبر (P.nigra) با نسبتهای متفاوت شامل 100 % و 0 % ، 75 % و 25% ، 50 % و 50 % و 25 % و 75 % به ترتیب برای ساقه ذرت و چوب صنوبر و با استفاده از دو دمای پرس 170 و180 درجه سانتیگراد و دو میزان مصرف چسب 10 و 12 درصد (براساس وزن خشک خرده‌چوب)، اقدام به ساخت تخته‌خرده‌چوب گردید. نتایج حاصل از این بررسی نشان داد که با افزایش دمای پرس از مقاومت خمشی و مدول‌الاستیسیته تخته‌ها کاسته شده است  درحالی‌که با افزایش مصرف چسب، ویژگیهای خمشی تخته‌ها به نحو معنی‌داری بهبود یافته است. همچنین با افزوده شدن خرده‌چوب صنوبر به ترکیب چوبی، مقاومت خمشی و مدول‌الاستیسیته تخته‌ها افزایش یافته است، در شرایطی که از 50 و 75 درصد خرده‌چوب صنوبر استفاده شده است این ویژگیها حداکثر بوده است. همچنین افزایش دمای پرس و کاهش ذرات ساقه ذرت در ترکیب چوبی باعث بهبود چسبندگی داخلی تخته‌ها گردیده است. نتایج حاصل از اندازه‌گیری واکشیدگی ضخامت تخته‌ها نیز نشان داد که افزایش دمای پرس و میزان مصرف چسب در سطح معنی‌داری، مقدار واکشیدگی ضخامتی را کاهش داده است. درحالی‌که با کاهش ذرات ساقه ذرت در ترکیب چوبی، واکشیدگی ضخامتی تخته‌ها افزایش یافته است. بنابراین در یک نتیجه‌گیری کلی می‌‌توان بیان نمود که از ساقه ذرت در صورتی‌که بین 25 تا 50 درصد در ترکیب چوبی استفاده شود، با استفاده از دمای پرس 170 درجه سانتیگراد و میزان مصرف چسب 10 درصد، امکان تولید تخته‌هائی با ویژگیهای استاندارد وجود دارد.}, keywords_fa = {تخته‌خرده‌چوب,ساقه ذرت,صنوبر,میزان مصرف چسب,دمای پرس,ویژگیهای فیزیکی و مکانیکی}, url = {https://ijwpr.areeo.ac.ir/article_117277.html}, eprint = {https://ijwpr.areeo.ac.ir/article_117277_f09cccfc211e68ceb815e9aa3d07dd39.pdf} } @article { author = {Fakhryan, Abas and Hosseinkhani, Hossein and Golbabaei, Fardad and Brazandeh, Mohammad mehdi}, title = {Pulping and paper making properties of Populus costanzo}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {25}, number = {2}, pages = {157-169}, year = {2010}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2010.117280}, abstract = {In this Investigation chemical, physical, morphology, pulp and paper making characteristics of   Populus costanzo were studied. The average dry and critical specific gravity was found to be  0.39and 0.36 and the fiber morphology including fiber length  , diameter ,lumen and thickness of cell wall 1.14 mm,28.84 µm, 28 µm ,and 2.92 µm was determined respectively. The average chemical composition including cellulose 50.74%, lignin 19.18%, Ext. 1.22%  and Ash 1.65% were measured. In order to cook and pulping, Kraft process was used. The maximum  yield and kappa number of Populus costanzo at 1 hour cooking time, 150°c cooking temperature and 12% effective alkali condition  obtained at 61.91% and 54.83 respectively and the minimum  yield and kappa number at 3 hour cooking time, 170°c cooking temperature and 16% effective alkali condition  obtained at 45.63% and 13.42 respectively.  }, keywords = {Populus costanzo,KRAFT PROCESS,yield,pulp,kappa number,Burst Strength,tear strength}, title_fa = {بررسی لیگنین زدایی و کاغذسازی چوب صنوبر کوستانزو ( Populus costanzo) به روش کرافت}, abstract_fa = {در این بررسی ویژگیهای فیزیکی، شیمیایی، ابعاد الیاف، خمیرکاغذ و کاغذسازی گونه صنوبر کوستانزو مورد تحقیق قرارگرفت. متوسط جرم ویژه خشک و بحرانی چوب به ترتیب 39/0 و 36/0 و میانگین طول‌الیاف، قطرالیاف، قطرحفره سلولی و ضخامت‌دیواره سلولی آن به ترتیب 14/1 میلی‌متر، 84/28 میکرون،00/24 میکرون و 92/2 میکرون اندازه‌گیری شد. میزان سلولز، لیگنین، خاکستر و مواداستخراجی چوب این درخت به ترتیب 74/50%، 18/19%، 65/1% و 22/1% تعیین شد. به منظور پخت وتهیه خمیر کاغذ  روش کرافت مورد استفاده قرار گرفت. بیشترین بازده وعددکاپای خمیر کاغذ صنوبرکوستانزو در زمان پخت 1ساعت، درجه حرارت پخت 150 درجه سلسیوس و قلیائیت موثر 12% به ترتیب با 91/61% و83/54 وکمترین بازده و عدد کاپا در زمان پخت 3 ساعت، درجه حرارت پخت 170 درجه سلسیوس و قلیائیت موثر 16% به ترتیب با 63/45% و42/13 بدست آمد. طول پاره شدن کاغذهای تهیه شده در زمان پخت 3 ساعت با 6953 متر دارای بیشترین مقدار بوده و در گروه A قرار گرفته است.  }, keywords_fa = {صنوبر کوستانزو,روش کرافت,بازده خمیرکاغذ,عدد کاپا,مقاومت در برابر ترکیدن,مقاومت در برابر پاره شدن}, url = {https://ijwpr.areeo.ac.ir/article_117280.html}, eprint = {https://ijwpr.areeo.ac.ir/article_117280_afd4c77f944e37212f6357921d2e288e.pdf} } @article { author = {Golbabaei, Fardad and Hosseinkhani, Hossein and Nourbakhsh, Amir and Kargarfard, Abolfazl and Fakhryan, Abas}, title = {An Investigation on the possibility of utilizing domestic wood in cooling towers}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {25}, number = {2}, pages = {170-186}, year = {2010}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2010.117281}, abstract = {Most industrial production processes need cooling water to operate efficiently and safely. Refineries، steel mills، petrochemical manufacturing plants، electric utilities and paper mills all rely heavily on equipment or processes that require efficient temperature control. Cooling water system control these temperatures by transferring heat from hot process fluids into cooling water. As this happens، the cooling water itself gets hot before it can be used again it must either be cooled or replaced by a fresh supply of cold water. The aim of this study was utilizing domestic wood in cooling towers structure. For this purpose، five wood spices included: Hornbeam، Oak، Alder،Populus and Tehran pine (Eldarica pine) and also five different regions with different climate، included: electric plant Montazer ghaem from Karaj near of Tehran، electric plant Loshan from north of Iran، electric plant Dorcheh Esfahan from center of Iran and petrochemical manufacturing plants Bandar emam from south of Iran، have been chosen. Sampling have been done and treated with CCA. All samples were put in the cooling towers and were tested during the study period. (Mechanical tests such as specific gravity، static bending، compression parallel to grain and hardness).  Based on this study، the mechanical properties of these spices during last four years were done. At the fifth year of study، virtual damages have not seen where as significant difference have been achieved in aspect of mechanical properties. Among of theses wood spices، Populous and Pinus eldarica had minimum mechanical degrade and it should be noted that Pinus eldarica spices had better quality than populous spices.    }, keywords = {Cooling tower,PHYSICAL AND MECHANICAL PROPERTIES,CELCURE}, title_fa = {بررسی امکان جایگزینی چوب گونه های بومی ایران در ساختمان برجهای خنک کننده}, abstract_fa = {جهت اجرای این طرح تحقیقاتی نمونه­هایی از گونه­های توسکا، افرا، بلوط، صنوبر و کاج الداریکا به ابعاد120× 5×5 سانتیمتر تهیه و با توجه به داشتن سیلندر و امکانات اشباع چوب در نیروگاه منتظر قائم کرج مطابق با روش متداول برای اشباع چوبهای برجهای خنک کننده با ماده حفاظتی سلکور اشباع شدند و پس از نگهداری به مدت حدود 2 ماه جهت تثبیت ماده حفاظتی، به 4 منطقه گیلان ( نیروگاه برق لوشان )، خوزستان ( پتروشیمی بندر امام)، استان اصفهان ( نیرو گاه برق دورچه) و استان تهران ( نیرو گاه برق منتظر قائم کرج) که از نظر شرایط محیطی بلحاظ آلودگی کاملا با یکدیگر متفاوت بودند انتقال و در داخل برجهای خنک کننده نصب شدند و در طول مدت 6 سال هرساله تعدادی از نمونه‌ها به آزمایشگاه انتقال و سختی، خمش استاتیک و فشارموازی‌الیاف اندازه‌گیری شد. نتایج حاصل از این بررسی نشان داد که بعداز گذشت 6 سال در نقاطق مختلف عوامل تخریب متفاوتی بر روی چوبها اثر گذاشته‌اند البته در طی 4 سال از نظر آماری تخریبی مشاهده نشده و در سال پنجم  اجرای طرح نیز از نظر دید ظاهری تخریبی مشاهده نشده ولی مقاومتها کاهش یافته‌اند. در منطقه صنعتی پتروشیمی ماهشهر با توجه به تولیدات مواد شیمیایی مختلف از جمله کلر و گوگرد که این مواد در هوا پخش شده و از طریق باد و عوامل مکش برج بر روی چوبها اثر کرده و باعث تخریب شیمیایی شده است در حالی که در سایر مناطق این آلودگی وجود نداشته و بیشتر تخریب بیولوژیکی اتفاق می‌افتد در بین گونه‌های مختلف استفاده شده جهت تهیه نمونه  گونه‌های بلوط و کاج‌الداریکا از نظر شکل ظاهری و مقاومتها استقامت بسیار بالایی داشته‌اند اما گونه بلوط با توجه به جذب آب زیاد آن دارای وزن بسیار زیادی نیز شده است که باعث افزایش وزن کلی سازه می‌شود که مطلوب نیست چوب کاج الداریکا با توجه به خصوصیات مناسب ساختمانی و مواد شیمیایی موجود در آن و با توجه به کاشت آن در ایران می‌تواند جایگزین بسیار مناسبی به جای چوب گونه‌های وارداتی باشد.}, keywords_fa = {برج‌های خنک کننده,بلوط,توسکا,صنوبر دلتوئیدس,افرا,کاج الداریکا,مقاومت مکانیکی,خواص فیزیکی}, url = {https://ijwpr.areeo.ac.ir/article_117281.html}, eprint = {https://ijwpr.areeo.ac.ir/article_117281_de95dc1b1839b1d1c3a9061ac753327d.pdf} } @article { author = {Basiji, Farshid and Safdari, Vahid reza and Jahan latibari, Ahmad and Nourbakhsh, Amir}, title = {Effect of fiber length on mechanical properties of wood composite plastic (Polypropylene)}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {25}, number = {2}, pages = {187-200}, year = {2010}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2010.117282}, abstract = {The objective of adding reinforcing fillers, such as natural fibers to plastics is to increase the strength compared with neat plastic and wood. In this research the effect of wood pulp fiber length (short, medium and long), aspect ratio and fiber content (27%, 37%, 47% and 0% (non-reinforced PP)) with 3% maleic anhydride grafted polypropylene on wood plastic composites (WPCs) has been studied.   Results showed that increased fiber length or aspect ratio and fiber content increases mechanical properties (tensile strength, tensile modulus and MOE). Impact strength had an inverse correlation with fiber content and fiber length, but fiber content was a much more important factor than fiber length for impact strength. The impact strength of composite of softwood pulps was much higher than wood floor composite plastic. The significant interaction between fiber length and fiber content, and the lack of a specific trend in the treatments made assessment of the effect of fiber properties on MOR difficult.    }, keywords = {Pulp fiber,FIBER LENGTH,Aspect ratio,fiber content,wood- plastic composite,MECHANICAL PROPERTIES}, title_fa = {اثر طول الیاف بر روی ویژگی‌های مکانیکی چند سازه چوب پلاستیک (پلی‌پروپلین)}, abstract_fa = {افزودن موادی نظیر الیاف طبیعی به فرآورده چندسازه پلاستیک، باعث افزایش برخی از  مقاومت­های  فرآورده ساخته شده در مقایسه با پلاستیک خالص می­شود. در این پژوهش اثرهای مربوط به طول الیاف خمیرکاغذ (کوتاه، متوسط و بلند)، ضریب­کشیدگی و مقدار الیاف (27 درصد، 37 درصد، 47 درصد و صفر درصد وزنی) با ماده جفت­کننده مالییک­انیدرید که در همه تیمارها 3 درصد و یکسان بوده بر روی ویژگی­های مکانیکی فرآورده چند سازه چوب پلاستیک مورد مطالعه قرار گرفت. الیاف خمیر­کاغذ و پلی­پروپلین در یک اکستردور با یکدیگر مخلوط و به داخل قالب تزریق و مطابق با استانداردهای مربوطه از آنها تخته تهیه شد. نتایج نشان داد که افزایش طول یا ضریب­کشیدگی و مقدار الیاف باعث افزایش ویژگی­های مکانیکی (مقاومت به کشش، مدول­کششی و MOE ) تخته­های ساخته شده می­شود. بنابراین مقاومت به ضربه با مقدار و طول الیاف همبستگی معکوس داشته است. به­طوری­که برای مقاومت به ضربه مقدار الیاف عامل مهم­تری نسبت به طول الیاف بوده است. همچنین مقاومت به ضربه پلاستیک تقویت­شده با الیاف خمیرکاغذ در مقایسه با پلاستیک تقویت­شده با خاک­اره بیشتر است. وجود روابط متقابل معنی­داری بین طول الیاف و مقدار الیاف برای ویژگی MOR و همچنین عدم وجود یک روند قابل درک در تیمارهای مربوط به MOR تا حدودی تجزیه و تحلیل مربوط به اثرهای طول و مقدار الیاف را بر روی این ویژگی مکانیکی با ابهام مواجه ساخته است.}, keywords_fa = {خمیرکاغذ,طول الیاف,ضریب کشیدگی,مقدارالیاف,چوب پلاستیک و ویژگی‌های مکانیکی}, url = {https://ijwpr.areeo.ac.ir/article_117282.html}, eprint = {https://ijwpr.areeo.ac.ir/article_117282_4fa0faf19a085169abc2d133d29d32a1.pdf} } @article { author = {Ghotbaldin, Farhad and Khademieslam, Habib alah and Nourbakhsh, Amir and Talaeipoor, Mohammad}, title = {The Effects of Some Production Variables on Physical and Mechanical Properties of Particleboard Made of Alnus subcordata by UF and MUF resin}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {25}, number = {2}, pages = {201-210}, year = {2010}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2010.117288}, abstract = {An experiment was conducted to study polymerization conditions and important production factors, the amount of resin and press temperature, on physical and mechanical properties of produced boards by urea formaldehyde (UF) and melamine urea formaldehyde (MUF) were compared. Purify UF resin (control treatment) and its mixture with MUF at 25, 50 and 75% proportions in 170 and 180˚C temperature were used to make homogen particle boards. The proportion of resin to particles was 10 percent by dry weight. Other production factors were assumed as fix factors. Eight experimental groups (treatment) with three replications per each were studied. Produced particles were derived from species Alnus subcordata. Physical and mechanical properties measurement prepared samples were based on European EN standard. Examined Physical characteristics were water absorption and thickness swelling and mechanical characteristics were modulus of rupture, modulus of elasticity and so internal bond. The data were analyzed in completely randomized design with factorial arrangement (4*2). Statistical significances among treatment means were determined by multiple range test of Duncan. The results of this study showed that physical and mechanical properties of boards were improved by increasing the level of MUF resin and temperature. Eventually, with consideration all results and so quality and economical aspects of produced particleboard by MUF resin and its comparison with control group we have concluded that 50 percent of MUF resin and 180 degree centigrade of press temperature are optimal levels.  }, keywords = {Particleboard,MUF resin,UF RESIN,press temperature,PHYSICAL AND MECHANICAL PROPERTIES}, title_fa = {تاثیر برخی از متغیر های تولید بر روی خواص فیزیکی و مکانیکی تخته خرده چوب ساخته شده از گونه توسکا بوسیله دو چسب UF و MUF}, abstract_fa = {در این بررسی شرایط پلیمر شدن و متغیرهای مهم تولید یعنی میزان استفاده از رزین و درجه حرارت پرس بر روی خواص فیزیکی و مکانیکی تخته های ساخته شده از دو نوع رزین UF و MUF مقایسه گردید. رزین UF بصورت خالص (تیمار شاهد) و مخلوط با رزین MUF در سطوح مختلف 25 ، 50 و 75 درصد بر مبنای 10 درصد وزن خشک خرده چوب و دو دمای پرس 170 و 180 درجه سانتیگراد جهت ساخت تخته خرده چوب همسان بکار گرفته شد. سایر عوامل تولید ثابت در نظر گرفته شدند. خرده چوب مورد استفاده از گونه جنگلی توسکا بدست آمد. در کل از مجموع عوامل متغیر مربوطه 8 تیمار حاصل گردید و برای هر تیمار سه تخته (تکرار) ساخته شد. ویژگی های فیزیکی مورد آزمایش شامل جذب آب و واکشیدگی ضخامت و ویژگیهای مکانیکی شامل مقاومت خمشی، مدول الاستیسیته و چسبندگی داخلی بود. تأثیر مستقل و متقابل عوامل متغیر بر ویژگی نمونه های ساخته شده با استفاده از طرح فاکتوریل کاملاً تصادفی و آزمون دانکن (DMRT) مورد بررسی قرار گرفت. نتایج حاصله نشان داد که هر چه میزان استفاده از رزین MUF بیشتر و دمای پرس بالاتر (˚C180)  باشد، در محدوده این تحقیق خواص فیزیکی و مکانیکی تخته های ساخته شده بهبود یافته است. در نهایت با توجه به نتایج حاصله و در نظر گرفتن جنبه های کیفی و اقتصادی تولید تخته خرده چوب با رزین MUF  و مقایسه خواص این تخته ها با نمونه های شاهد حد بهینة عوامل متغیر با فرض شرایط ثابت این تحقیق، استفاده از رزینMUF در سطح 50% و دمای پرس 180 درجه سانتیگراد می باشد.}, keywords_fa = {تخته خرده چوب,رزین MUF,رزین UF,دمای پرس,خواص فیزیکی و مکانیکی}, url = {https://ijwpr.areeo.ac.ir/article_117288.html}, eprint = {https://ijwpr.areeo.ac.ir/article_117288_0a1e08493b7395bdc56826f7b71686c8.pdf} } @article { author = {Mansoryar, Eiraj and Karimi, Alinaghi and Ebrahimi, Ghanbar and Mirshokraei, Ahmad and Rahimi, Sohrab}, title = {Water repelling Populus Alba by emulsion of paraffin, Quaternary ammonium and hydrated starch}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {25}, number = {2}, pages = {211-222}, year = {2010}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2010.117290}, abstract = {The water repellency and dimensional stabilization of wood species are important for outdoor uses. In this study, the water absorption and water repelling of poplar wood (Populus Alba) by emulsion of paraffin, Quaternary ammonium and starch, were investigated. Paraffin in three levels of 0%, 3%, 5%, Quaternary ammonium in three levels of 0%, 1.5%, 2.5% and also starch in three levels of 0%, 1% and 2%(by weight) were selected as variables. A set of matched specimens were set aside as control, for making comparison. Results showed that the amount of paraffin had a positive significant effect on water absorption and water repellency that is increasing paraffin would improve these properties. Furthermore, specimens treated with paraffin had better water repellency than control samples. Based on the results, it is claimed that the treatment of 5% paraffin, 0-1.5% Quaternary ammonium and 0-1% starch will bring about water absorption and water repellency in treated specimens to a desired level, without causing any damage to other physical properties of them.}, keywords = {Paraffin,Quaternary ammonium,starch,water repelling,poplar wood}, title_fa = {آبگریز کردن چوب صنوبرکبوده ((Populus alba) با استفاده از امولسیون پارافین،کواترنری آمونیوم و نشاسته هیدراته}, abstract_fa = {پیشگیری از نوسان رطوبت چوب و افزایش ثبات ابعاد و ضد آب کردن آن بویژه در مصارف بیرونی موضوع مهمی است.به نحوی که در این پژوهش برای کنترل رطوبت و ضد آب کردن چوب صنوبر کبوده با اشباع آن توسط امولسیون ترکیبی با نسبت های وزنی مختلف پارافین (0، 3 و 5 درصد)، کواترنری آمونیوم (0، 5/1 و 5/2 درصد) و نشاسته هیدراته (0،1 و 2 درصد) استفاده شده و خواص فیزیکی شامل درصد جذب آب و خاصیت آبگریزی اندازه گیری شده است. نمونه های جور و سالم که مورد تیمار این امولسیون قرار نگرفته بودند به‌عنوان شاهد انتخاب شدند. نتایج نشان داده است که مقدار پارافین تاثیر معنی‌داری بر جذب آب و خاصیت آبگریزی داشته، به طوری که با افزایش مقدار پارافین این خواص بهبود یافته‌اند. به طور کلی نمونه‌های تیمار شده با پارافین، آبگریزی بیشتری نسبت به نمونه‌های شاهد داشته‌اند. خواص فیزیکی نمونه‌های تیمارشده با این محلول امولسیون، مورد بررسی قرار گرفت تا تاثیر این تیمار روی خواص فیزیکی آنها نسبت به شاهد تعیین شود. بنابراین محلول حاوی 5 درصدپارافین، 5/1-0 درصدکواترنری آمونیوم و1-0 درصدنشاسته، در زمینه حفظ خواص فیزیکی تاثیر مطلوبی را داشته است.}, keywords_fa = {پارافین,کواترنری آمونیوم,نشاسته هیدراته,آبگریز کردن,صنوبر}, url = {https://ijwpr.areeo.ac.ir/article_117290.html}, eprint = {https://ijwpr.areeo.ac.ir/article_117290_b6bc1fe2f9b54746419b8f4a5a029254.pdf} } @article { author = {Akbarpoor, Iman and Resalti, Hossein and Saraeyan, Ahmad reza}, title = {Enzymatic Versus Chemical Deinking of Old Newspaper}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {25}, number = {2}, pages = {223-233}, year = {2010}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2010.117292}, abstract = {In this study, Deinking of old newspaper was investigated by chemical and enzymatic methods. Chemical treatment was done using chemicals at different times of 10, 20 and 30 minutes, consistency of 10%, temperature of 50±1!C along with washing, flotation and combination of washing/flotation. While, Enzymatic treatment was accomplished at different concentrations of 0.025, 0.05, 0.1 and 0.2% of cellulase enzyme (on the basis of oven dried waste paper), pH range of   5-5.5, different times of 10,15 and 20 minutes, consistency of 10%, temperature of 50±1!C along with washing. The results comparison of optimum chemical and enzymatic treatments showed that, deinked pulp by chemical method had higher brightness and yellowness. Also, deinked pulp by chemical method resulted the papers with higher bulk, higher caliper and higher air resistance.}, keywords = {Deinking,Old newspaper,Cellulase Enzyme,Optical properties,physical properties}, title_fa = {جوهرزدایی آنزیمی‌کاغذ روزنامه باطله در مقایسه با روش شیمیایی متداول}, abstract_fa = {در این تحقیق جوهرزدایی کاغذ روزنامه باطله به دو روش شیمیایی متداول و آنزیمی‌مورد بررسی قرار گرفت. تیمار شیمیایی کاغذ روزنامه باطله با استفاده از مواد شیمیایی در زمانهای مختلف10،20 و30 دقیقه، درصد خشکی10 درصد، دما 1±50 درجه سانتی‌گراد همراه با شستشو، شناورسازی وترکیب شستشو و شناورسازی انجام شد. این در حالی است که تیمار آنزیمی‌با استفاده از آنزیم سلولاز در غلظت‌های مختلف 025/0 ، 05/0 ،1/0 و2/0 درصد (براساس وزن خشک کاغذ باطله)، محدوده 5/5-5 pH ، زمانهای مختلف10، 15 و20 دقیقه، درصد خشکی10 درصد، دما 1±50 درجه سانتی‌گراد همراه با شستشو انجام گرفت. مقایسه نتایج خواص نوری تیمارهای بهینه شیمیایی و آنزیمی‌نشان داد که خمیرهای کاغذ جوهرزدایی شده به روش شیمیایی متداول دارای درجه روشنی بیشتر و زردی بیشتر می‌‌باشند. همچنین خمیرهای کاغذ جوهرزدایی شده به روش شیمیایی متداول کاغذهای حجیم‌تر، ضخیم‌تر و با مقاومت به عبور هوای بیشتری را نتیجه داد.}, keywords_fa = {جوهرزدایی,کاغذ روزنامه باطله,آنزیم سلولاز,خواص نوری,خواص فیزیکی}, url = {https://ijwpr.areeo.ac.ir/article_117292.html}, eprint = {https://ijwpr.areeo.ac.ir/article_117292_02b4b3a1da81bdd512364f299647ab96.pdf} } @article { author = {tarmian, asghar and Sepehr, Amir}, title = {Investigation on the heat transfer and evolution of temperature gradient through wood during drying; Case study: beech (Fagus orientalis) and spruce (Picea abies)}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {25}, number = {2}, pages = {234-247}, year = {2010}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2010.117291}, abstract = {The heat transfer through three orthotropic directions and the evolution of temperature gradient in beech (Fagus orientalis) and spruce (Picea abies) during drying were investigated. Thus, due to low capacity of dryer, small flat-sawn boards with dimensions of 80 × 25 × 40 mm (L×R×T) were used. Then, the boards were dried at the dry-bulb temperature of 60 °C and relative humidity of 50 %. Four surfaces of the boards were coated by polyurethane-coated aluminum foil to confine the heat flux along one direction. Then, the boards were thermally insulated by 50 mm-thick Styrofoam. Some holes with 1mm in diameter were made on the board specific distances to measure the temperature using thermocouple. The results showed that the temperature of each wood increased as heating up progressed until it reached to the wet-bulb temperature. Then, it remained at an almost constant value as the wet bulb temperature until the wood moisture content reached the hygroscopic range. Furthermore, the pattern of the temperature profile for both wood species was almost identical. The surface temperature of the boards increased until it reached the dry-bulb temperature of 60 °C, while the core temperate remained as the wet-bulb temperature (48-52 °C) throughout the rest of drying period.}, keywords = {Heat transfer,Temperature profile,drying,Spruce,beech}, title_fa = {بررسی فرایند انتشار حرارت و توسعه گرادیان دما در چوب طی خشک‌شدن؛ مطالعه موردی: راش (Fagus orientalis) و نوئل(Picea abies)}, abstract_fa = {فرآیند انتشار حرارت در سه جهت ارتوتروپ و توسعه گرادیان دما در گونه­های چوبی راش (Fagus­ orientalis) و نوئل (Picea abies) طی خشک شدن بررسی شد. برای این منظور و با توجه به کم بودن ظرفیت خشک­کن از تخته­های مماسی کوچک به ابعاد 40× 25×80 (L×R×T) میلی­متر استفاده شد. سپس، تخته­ها در در دمای خشک 60 درجه سانتیگراد و رطوبت نسبی 50 درصد خشک شدند. برای محدود کردن انتشارحرارت در یک راستا و اندازه­گیری انتقال حرارت در یک جهت تخته، پنج سطح از شش سطح تخته­ها با فویل آلمینیومی آغشته با رزین پلی‌اورتان اندود شد و سپس از یک پلاستوفوم با ضخامت 50 میلی­متر به­عنوان عایق حرارت بر روی تخته­ها استفاده شد. برای اندازه­گیری دما با ترموکوپل، سوراخ­هایی به قطر یک میلی­متر در فواصل معین در تخته­ها ایجاد شد. نتایج نشان داد که دمای هر دو گونه چوبی طی خشک­شدن به تدریج افزایش یافته تا وقتی که به دمای تر برسد. سپس، در این دما باقی می­ماند تا وقتی که رطوبت چوب وارد دامنه هیگروسکپیک شود. همچنین، گرادیان دما در هر دو گونه چوب الگوی مشابهی داشت، به این ترتیب که دمای لایه سطحی تخته­ها تا دمای خشک 60  درجه سانتیگراد افزایش یافت، ولی دمای مغز تخته‌ها تا پایان عملیات خشک­شدن درحد دمای‌تر(48 -52 درجۀ سانتیگراد) باقی­ماند.}, keywords_fa = {انتقال حرارت,گرادیان دما,خشک کردن,نوئل,راش}, url = {https://ijwpr.areeo.ac.ir/article_117291.html}, eprint = {https://ijwpr.areeo.ac.ir/article_117291_381dd6fc03a51976b1a097a58707c242.pdf} } @article { author = {Safdari, Vahid}, title = {Morphological and chemical components of Ulmus glabrar, Ulmus compestris, Zelkova carpinifolia, Celtis australis}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {25}, number = {2}, pages = {248-259}, year = {2010}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2010.117312}, abstract = {The suitability of wood and noon-wood species for using in pulp and paper industry can be predicted by their morphological and chemical characteristics. In these research morphological and chemical properties of four spices of Ulmacea family, Ulmus glabrar, Ulmus compestris, Zelkova carpinifolia and Celtis australis have been compared. From each species three cross section, 5 cm thickness has been selected. Wood slivers of tree zones: near to pith, middle part and near to bark wood have been macerated in mixture of acetic acid and hydrogen peroxide at 60°C for 48 hours. Biometric coefficients of fibers in three zone and four species have been measured and analyzed by factorial, complete randomized block design. Result showed that, Zelkova carpinifolia has least lignin, ash and extractives and highest cellulose. The fibers of, Zelkova carpinifoliahas has highest Slenderness ratio, Runkel ratio and hence in Ulmacea family is most suitable species for paper industry. Fiber length, wall thickness in near to bark zone in comparison to near to pith was higher significantly. Therefore it is predicted that the mechanical properties of pulp of this three zones are different}, keywords = {Fiber morphology,Chemical components,Ulmus glabrar,Ulmus compestris,Zelkova carpinifolia,Celtis australis}, title_fa = {ویژگی‌های مورفولوژیکی و ترکیبات شیمیایی چوب ملج، اوجا، آزاد و داغداغان}, abstract_fa = {از طریق ویژگی­های مورفولوژیکی و ترکیبات شیمیایی می­توان کیفیت گونه­های چوبی و غیرچوبی را برای استفاده در صنایع خمیرکاغذ پیش­بینی نمود. در این مطالعه ویژگی­های مورفولوژیکی و ترکیبات شیمیایی چوب چهار گونه­ درختی بومی ایران از خانواده نارون­ها (Ulmaceae) که عبارتند از ملج (Ulmus glabra)، اوجا (Ulmus compestris)، آزاد (Zelkova carpinifolia) و داغداغان(Celtis australis)،  مورد مقایسه قرار گرفتند. سه درخت از هر گونه انتخاب و از هر کدام یک مقطع عرضی (دیسک) به ضخامت 5 سانتی­متر تهیه شد. از سه بخش نزدیک به مغز، میانه و نزدیک به پوست خلال­های چوبی تهیه و در محلول اسید استیک و آب اکسیژنه (نسبت 1 به 1)، در دمای60 درجه سانتی­گراد به مدت 48 ساعت گذاشته شدند تا دیفیبره شوند. به­طوری­که ضریب­های بیومتری الیاف در سه بخش و در چهار گونه اندازه­گیری و توسط طرح آماری فاکتوریل در قالب بلوک کامل تصادفی تجزیه و تحلیل شدند. نتایج نشان داد که گونه آزاد کمترین مقدار لیگنین، خاکستر و مواد استخراجی و بالاترین مقدار سلولز را داراست. همچنین الیاف این گونه از بالاترین ضریب درهم­رفتگی و ضریب رونکل برخوردار بوده، در نتیجه در میان خانواده نارون­ها (Ulmaceae) مناسب­ترین گونه مورد استفاده در کاغذسازی می­باشد. طول فیبر و همچنین ضخامت دیواره الیاف بخش نزدیک به پوست نسبت به بخش نزدیک به مغز به­صورت معنی­داری بیشتر بوده که پیش­بینی می­شود خواص مکانیکی خمیرکاغذ تولیدی در نواحی سه­گانه با یکدیگر متفاوت باشند.}, keywords_fa = {مورفولوژی الیاف,ترکیبات شیمیایی,ملج,اوجا,آزاد و داغداغان}, url = {https://ijwpr.areeo.ac.ir/article_117312.html}, eprint = {https://ijwpr.areeo.ac.ir/article_117312_bd6a6ad192848bc281584002d870036a.pdf} } @article { author = {Kshn dehghan, Afshin and Khademi eslam, Habibalah and Bazyar, Behzad}, title = {Evaluation of Natural durability of Horn beam (Carpinus betulus) wood against Coriolus Versicolor in case of Treated with CCA (Tanalith c)}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {25}, number = {2}, pages = {260-274}, year = {2010}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2010.117313}, abstract = { In this study, the influence of the fungus (Coriolus versicolor) on the durability of Horn beam (carpinus betulus) in natural state and treated with CCA (Copper/Chromium/Arsenic) was evaluated. CCA is a kind of water borne preservatives that was used to treat specimens under vacuum and pressure (Bethel procedure) with amount of 3.5 & 1.5 percent on the basis of oven dry wood. Specimens were contaminated with cultured fungus for eight weeks in incubator. After this period, weight reduction, compressive strength (parallel to grain) and hardness of specimens were measured. Weight reduction of treated samples with 3.5 & 1.5 percent CCA were 1.68 and 1.73 percent respectively. Weight reduction of control samples were much higher (22.87 percent) than treated ones. There was no significant difference between the Compressive strength (parallel to grain) of treated and control samples without effect of fungus but the samples with effect of fungus have significant difference. Compressive strength (parallel to grain) of treated samples with 3.5 & 1.5 percent of CCA were 64.33 and 60.10 (Mpa) respectively but Compressive strength (parallel to grain) of control samples were much lower (38.44 Mpa) than treated samples. There was no significant difference between the hardness of treated and control samples without effect of fungus. On the other hand, the hardness of treated samples was more than control samples slightly, but this difference was not significant in 5 percent level. The hardness of treated and control samples with effect of fungus have significant difference. Hardness of treated samples with 3.5 & 1.5 percent of CCA were 5788(N) and 5799(N) respectively. However the hardness of control samples were much lower (3139N) than treated samples. Eventually CCA (Tanalith c) increased the durability of Horn beam (Carpinus betulus) from nondurable level to durable level.}, keywords = {}, title_fa = {بررسی دوام چوب ممرز در حالت طبیعی و تیمار شده با نمک CCA (تانالیتc) دربرابر قارچ رنگین کمان}, abstract_fa = {در این تحقیق اثر قارچ رنگین‌کمان بر روی مقاومت چوب ممرزCarpinus betulus )  ( در حالت طبیعی و حفاظت شده با نمک محلول در آب CCA (تانالیت c)، با غلظت‌های 5/1 و 5/3 درصد با استفاده از ظروف کوله (kolle Flasks )  و طبق آزمون استاندارد بازیدیومیست  EN 113 ، Din واستاندارد  ASTMمورد مطالعه و بررسی قرار گرفت. برای انجام این بررسی از طرح فاکتوریل با بلوک‌های کاملاً تصادفی استفاده شد. نمونه‌های به دست آمده از سه اصله درخت ممرز درجنگل موزه کام ساری استحصال گردید و 270 نمونه‌ی کاملاً سالم از میان حدود 2000 نمونه ی استحصال شده انتخاب شد و نتایج عددی استخراج شده مورد بررسی قرار گرفت. نمونه‌ها با استفاده از روش خلا- فشار انجام گرفت. نمونه‌های تیمار شده و شاهد بر روی ریسه‌های قارچ رنگین کمان در ظروف کوله بر روی محیط کشت مالت اکستراکت آگار قرار داده شدند و ریسه‌های قارچ در شرایط حرارتی 22 درجه‌ی سانتی‌گراد و رطوبت نسبی 75 درصد در داخل انکوباتور(Incubator) به مدت 8 هفته روی نمونه‌های چوب به رشد خود ادامه دادند. سپس کاهش جرم، مقاومت فشار موازی الیاف و مقاومت به سختی نمونه‌ها اندازه‌گیری شد. کاهش جرم نمونه‌های اشباع شده با تانالیت c در مقایسه با نمونه‌های شاهد، در سطح 5 درصد معنی‌دار است، به طوری که چوب ممرز، مطابق طبقه بندی(Findlay) از حالت کم دوام به حالت بادوام تبدیل شد. در مقاومت فشارموازی الیاف، نمونه‌های اشباع شده و شاهد بدون تاثیر قارچ، تفاوت معنی‌دار نداشتند، اما مقاومت فشارموازی الیاف نمونه‌های اشباع شده و شاهد با تاثیر قارچ، تفاوت معنی‌دار داشتند. درمقاومت به سختی نیز نمونه‌های اشباع شده و شاهد بدون تاثیر قارچ، تفاوت معنی‌دار نداشتند ولی مقاومت به سختی نمونه‌های اشباع شده و شاهد با تاثیر قارچ دارای تفاوت معنی‌دار بودند. بنابراین ماده‌ی حفاظتی به تنهایی اثری در افزایش یا کاهش این دو مقاومت نداشت، اما بدون در نظر گرفتن اثرات تخریبی قارچ، این ماده‌ی حفاظتی در سطح معنی‌دار باعث افزایش مقاومت به فشارموازی الیاف و مقاومت به سختی نمونه‌ها شد.}, keywords_fa = {ممرز,تانالیت c,بازیدیومیست,قارچ رنگین کمان,مالت اکستراکت آگار,کوله,انکوباتور}, url = {https://ijwpr.areeo.ac.ir/article_117313.html}, eprint = {https://ijwpr.areeo.ac.ir/article_117313_a47a6ad3625e0d715a43266afe8dff29.pdf} } @article { author = {Sharari, Meraj and Jahan latibari, Ahmad and Rafiei, Gholamreza and Mirshokraei, Ahmad}, title = {Investigation on the influence of nutrients and treatment period on enzyme activities of Phanerochaete chrysosporium}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {25}, number = {2}, pages = {275-290}, year = {2010}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2010.117314}, abstract = {In the course of enhanced bioremediation, addition of nutrients such as carbon, nitrogen, phosphorous, etc, substrates, electron acceptors as well as vitamins (Thiamin, etc) and veratryl alcohol, increased metabolic activities, will influence the production of enzymes and enhances the deterioration of pollutants. In this study, the effect of 1% (V/V) of nutrients containing various mineral salts, carbon (glucose and malt), nitrogen (casein peptone yeast extract) and some enzyme inducer, such as veratryl alcohol and thiamin hydrochloride on production of laccase, peroxidase and xylanase enzymes by Phanerochaete chrysosporium in bagasse preparation effluent is investigated. The results showed that MSB+MCTV is the most effective additive which causes the highest lignolitic activity of  this fungus after 5 to 7 days in case of laccase and peroxidase and 3 days for xylanase, and maximizes the production of the enzymes. The production of these enzymes is measured at 78, 193 and 60 U/l respectively. However, in conditions without additives, the relevant values are 26, 54 and 16 U/l respectively. The relation between different stages of fungus growth and enzyme production and changes in lignin and carbohydrate of effluent after the period of nine days is also investigated.}, keywords = {Nutrients,laccase,peroxidase,xylanase,Phanerochaete chrysosporium,Bagasse preparation effluent}, title_fa = {بررسی تاثیر مواد مغذی و زمان تیمار بر فعالیت‌های آنزیمی قارچ Phanerochaete chrysosporium}, abstract_fa = {در فناوری تخریب‌زیستی تسهیل شده، توسط افزودن مواد مغذی (منابع کربن، نیتروژن، فسفر...)، سوبستراها، گیرنده‌های الکترون و ویتامین‌ها (تیامین، ...)، همراه با افزایش فعالیت‌های متابولیکی، می‌توان ترشح آنزیم‌ها را تحت تاثیر قرار داده و میزان تخریب آلاینده‌ها را افزایش داد. به همین منظور، با استفاده از (V/V) %1 ترکیبات مختلف مواد مغذی شامل نمک‌های معدنی، منابع کربن و نیتروژن (گلوکز، مالت و کازئین پپتون یست اکسترکت) و محرک‌های ترشح آنزیم نظیر وراتریل الکل و تیامین هیدروکلراید اثر این مواد بر فعالیت‌‌های آنزیم‌های لاکاز، پراکسیداز و زایلاناز ترشح شده توسط قارچ  Phanerochaete chrysosporiumدر محیط پساب آماده‌سازی باگاس بررسی شده است. نتایج نشان می‌دهند که MSB+MCTV  موثرترین ترکیب افزودنی است که در حداکثر فعالیت لیگنولیتیکی این قارچ (روزهای پنجم تا هفتم تیمار برای آنزیم‌های لاکاز و پراکسیداز و روز سوم برای آنزیم زایلاناز) ترشح این آنزیم‌ها را افزایش می‌دهد. به طوری ‌که مقادیر این آنزیم‌ها به ترتیب تا معادل 78، 193 و U/l60 خواهد شد. در حالی که، بدون افزودن مواد مغذی به محیط پساب، این مقادیر در حد 26، 54 و U/l 16 بوده‎اند. رابطه فازهای مختلف رشد قارچ و میزان ترشح آنزیم و همچنین تغییر میزان لیگنین و کربوهیدرات‌های موجود در پساب در طی تیمار 9 روزه مورد بررسی قرار گرفته است.}, keywords_fa = {مواد مغذی,لاکاز,پراکسیداز,زایلاناز,Phanerochaete chrysosporium,پساب آماده‌سازی باگاس,تصفیه زیستی}, url = {https://ijwpr.areeo.ac.ir/article_117314.html}, eprint = {https://ijwpr.areeo.ac.ir/article_117314_f789235919c04da4de133f4a3ea56301.pdf} } @article { author = {Tasoji, Mohamad and Tabrsa, Taghi and Mohammadi, Alireza}, title = {Making wheat straw particleboards by using mixture of MF and UF resins}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {25}, number = {2}, pages = {291-301}, year = {2010}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2010.117315}, abstract = {For making wheat straw particleboards, different mixtures of UF and MF resins were used. The ratio of UF : MF was 0:100,75:25,50:50,25:75 and 100:0 based on weight of resin and boards densities were set to 0.7 . The physical and mechanical properties such as Thickness Swelling(TS)(after 2 and 24 hours), Internal Bonding(IB) , Modulus Of Elasticity(MOE) ,Modulus Of Rupture(MOR) were determined and compared to EN 312-4 standard. The highest amounts of IB ,MOR and MOE are from the boards that were made from 50:50 (UF:MF) . All of The boards MOE and MOR amounts of all treatments except treatment 100:0 (UF:MF) were in range of EN 312-4 standard but the IB amounts were not. The TS amount was improved in the boards with more MF content but it was not in EN 312-4 range. Due to the thin waxy layer that covers the outer most layer of wheat straw surface, the non polar structure of this layer brings incompatibility between polar resins and wheat straw particles and this incompatibility will result in low physical and mechanical property for wheat straw particleboards. Also due to low porosity of waxy layer, the distribution of formaldehyde polar resins on straw particles surface, not well occur and this itself is an important factor in decrease of physical and mechanical resistance in wheat straw particleboards.}, keywords = {wheat straw particleboard,Urea formaldehyde resin,Melamine formaldehyde resin,waxy layer}, title_fa = {ساخت تخته‌خرد‌ه‌کاه با استفاده از مخلوط رزین‌های اوره و ملامین‌فرمالدهید}, abstract_fa = {با استفاده از مخلوط رزین­های اوره‌فرمالدهید و ملامین‌فرمالدهید, تخته­خرده­کاه­هایی ساخته شد. نسبت­های وزنی اوره‌فرمالدهید: ملامین‌فرمالدهید, 100: 0, 75 : 25, 50 : 50, 25 : 75 و0 : 100 انتخاب شدند و دانسیته تخته­ها 7/0 گرم بر سانتی­متر­مکعب در نظر گرفته شد. مقاومت­های فیزیکی و مکانیکی از جمله واکشیدگی ضخامت (بعد از 2 و 24 ساعت غوطه­وری در آب), چسبندگی‌داخلی, مدول‌الاستیسیته و مدول‌خمشی تخته­های حاصل اندازه‌گیری و با استاندارد4-312EN مقایسه شدند. بالاترین مقادیر چسبندگی‌داخلی, مدول‌خمشی و مدول‌الاستیسیته مربوط به تخته­های ساخته شده با نسبت وزنی اوره‌فرمالدهید : ملامین‌فرمالدهید( 50 : 50 ) بود. مقادیر مربوط به مدول‌الاستیسیته و مدول‌خمشی همه تیمارها به جز تیمار اوره‌فرمالدهید: ملامین‌فرمالدهید (100:0) در محدوده استاندارد 4-312EN بوده در حالی ­که مقادیر مربوط به چسبندگی‌داخلی تمام تیمارها, در محدوده این استاندارد نمی­باشند. مقدار واکشیدگی ضخامت, در تخته­های با مقدار ملامین‌فرمالدهید بیشتر, بهبود داشت اما این مقدار در محدوده استاندارد  4-312EN قرار نمی­گیرد. از آنجایی که لایه مومی‌نازکی سطح کاه گندم را پوشانده, ساختار آبگریز این لایه باعث ایجاد ناسازگاری بین رزین­های آبدوست فرمالدهیدی و ذرات کاه گندم می­شود و این ناسازگاری منجر به کاهش مقاومت­های فیزیکی و مکانیکی تخته­خرده­کاه­های حاصل خواهد شد. همچنین به دلیل نفوذپذیری پایین لایه مومی, پخش رزین آبدوست فرمالدهیدی, روی سطح ذرات کاه به خوبی صورت نگرفته که خود عاملی مهم در کاهش مقاومت­های فیزیکی و مکانیکی تخته­های حاصل از کاه گندم می‌باشد.   }, keywords_fa = {تخته‌خرده‌کاه,رزین ملامین‌فرمالدهید,رزین اوره‌فرمالدهید,لایه مومی}, url = {https://ijwpr.areeo.ac.ir/article_117315.html}, eprint = {https://ijwpr.areeo.ac.ir/article_117315_783e3ffed9c869981ad7eed943ad2f9e.pdf} } @article { author = {Roshanasan, Jalil and Dehghani firozabadi, Mohammadreza and Dahmardeh ghaleh no, Mohammad and Sharifi, Saeideh}, title = {Investigation lignin dissolution at pulping process of wheat straw}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {25}, number = {2}, pages = {302-308}, year = {2010}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2010.117316}, abstract = {The lignin dissolution in Kraft pulping for wheat straw was studied. Kraft pulping was carried out under the conditions: chemical charge of 18% (as NaOH, based on o.d. bagasse), sulfidity of 25% and liquor to wheat straw ratio of 10:1. Six cooking maximum temperatures of 85,100,110,120,130 and 150 ◦C, were selected and reaction time varied from 0 to 250 min. based on maximum temperature. The Klason lignin, acid soluble lignin, ash and extractive contents of wheat straw were 18.4%, 2.07%, 3.24% and 4.56 respectively. During alkaline pulping of wheat straw, about 64% and 52% of lignin was removed before reaching to the temperature 100 ◦C and 85 respectively. The values pulp and carbohydrates yield were, about 64%, 58% for 85 ◦C and 61%, 57% for 100◦C.}, keywords = {WHEAT STRAW,Klason lignin,Acid Soluble Lignin,Delignification and Kraft}, title_fa = {بررسی انحلال لیگنین در خمیرسازی کرافت از کاه گندم}, abstract_fa = {در این تحقیق چگونگی انحلال لیگنین در خمیرسازی کرافت از کاه گندم تجن، مورد بررسی قرار گرفت. در این مطالعه، زمان خمیرسازی (240-0 دقیقه) و دمای خمیرسازی (150-85 درجه سانتی‌گراد) به عنوان عوامل متغیر و سایر عوامل ثابت در نظر گرفته شد. در این تحقیق میزان لیگنین محلول در اسید و لیگنین کلاسون، مواد استخراجی و خاکستر کاه گندم اندازه‌گیری گردید که به‌ترتیب 07/2، 14/18 و 24/3 درصد محاسبه گردید. نتایج نشان می‌دهد که با افزایش دمای خمیرسازی از مقدار لیگنین باقیمانده در خمیر کاسته می‌شود، به طوری که تا دمای 85 درجه سانتی‌گراد در حدود 52 درصد لیگنین و تا دمای 100 درجه سانتی‌گراد در حدود 64 درصد لیگنین خارج می‌شود. بازده خمیر در دمای 85 درجه سانتی‌گراد حدود 64 درصد و بازده کربوهیدرات‌ها 58 درصد و در دمای 100 درجه سانتی‌گراد بازده خمیر 61 درصد و بازده کربوهیدرات‌ها در حدود 57 درصد به دست آمد.}, keywords_fa = {کاه گندم تجن,لیگنین کلاسون,لیگنین محلول در اسید,خمیرسازی و خمیر کرافت (کاه گندم)}, url = {https://ijwpr.areeo.ac.ir/article_117316.html}, eprint = {https://ijwpr.areeo.ac.ir/article_117316_0ff81c26940c5d9afec798c3815de8dd.pdf} } @article { author = {Ebrahimpoor kasmani, Jafar and Nazeri, Amir mohssen and Ashryeh, Ali}, title = {Investigation on the Effects of humidity and heat of combined papers on quality of CorrugatedBoard}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {25}, number = {2}, pages = {309-320}, year = {2010}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2010.117317}, abstract = {              In this investigation , effects of different humidity and heat on quality of Corrugated board , was studied , and optimum treatment indicated Variables in this Paper was : Corrugator speed (50,100,150m/min) ,wraping angle of the paper around preheaters (90,180,300 degree) and moisture of paper (6.5%,7%,8.5%). Papers that treated for this purpose was included : 125gsm kraft liner ,127 gsm medium paper and 140gsm test liner paper. A flut type of 3ply Corugated board was selected for this study.Moisture of paper was measured in 3 places : Paper on roll stand before single facer , paper after singlefacer preheater and paper before incoming doublefacer in hot plate unit. Also temprature was measured in corrugator rolls ,hot Plates in double facer and final Board after Exiting of the Machine.   Results show that , warp of final board decreased in speed 50 and 100m/min ,moisture 7% and 1800  wraping angle of the paper around preheater.   That means lower speeds and higher wraping angles cause to more heat on corrugated board and decreasing in warp content resulted.It should be noted that lower humidity more than 7% and increase wraping angle more than 180 degree cause to over drying and intensive moisture decrease in final board that cause to reverse warp in final board.}, keywords = {Corrugatedboard,humidity,heat,liner paper,Medium paper,warp}, title_fa = {بررسی تاثیر رطوبت ودرجه حرارت کاغذهای متشکله برکیفیت مقوای کنگره‌ای}, abstract_fa = {در این تحقیق با بکار بردن درجه حرارت‌ها و رطوبت‌های مختلف کاغذ، میزان تاثیرهای آنها برکیفیت ورق کارتن مورد بررسی قرارگرفت و بهترین حالت مشخص شد. متغیرهای مورد بررسی شامل سه متغیر سرعت(در سه سطح50-100 – 150 متر در دقیقه) زاویه پیچش کاغذ به دور سیلندرهای پیش گرمکن(در سه سطح 90-180-300 درجه) و رطوبت کاغذ( سه سطح 5/6-7- 5/8 درصد ) بودند. کاغذهایی که مجموعه تیمارهای مورد بررسی بر روی آنها اعمال شدند شامل: کرافت 125 گرمی‌– فلوتینگ 127گرمی‌و بازیافت 140گرمی‌بودند. ورق کارتن مورد مطالعه به‌صورت سه لایه و از نوع A فلوت در نظر گرفته شد. رطوبت کاغذ در سه محل شامل: رول کاغذ بر روی جک رول و بعد از پیش گرمکن کنگره‌ساز و همین‌طور قبل از واحد چسب‌زنی و پلاتهای گرم اندازه‌گیری شد. درجه حرارت نیز در نوردهای کنگره‌ساز و پلاتهای بخار و ورق نهایی خارج شده از دستگاه اندازه‌گیری شد. نتایج نشان داد که میزان کاسی در سرعتهای 50 و100 متربر دقیقه، رطوبت7% و میزان زاویۀ پیچش 180درجه به حداقل رسید، یعنی سرعت کمتر و زاویۀ پیچش بیشتر سبب اعمال حرارت بیشتر بر ورق مقوا و کاهش رطوبت می‌شود. البته، این نکته قابل ذکر است که کاهش رطوبت بیش از 7% و افزایش زاویۀ پیچش بیش از 180درجه سبب خشکی بیش از حد و کاهش رطوبت شدید و در نتیجه بروز کاسی بر عکس در ورق مقوا خواهد شد.}, keywords_fa = {مقوای کنگره‌ای,رطوبت,حرارت,کاغذ لاینر,کاغذ فلوتینگ,کاسی}, url = {https://ijwpr.areeo.ac.ir/article_117317.html}, eprint = {https://ijwpr.areeo.ac.ir/article_117317_773d9efdd1bc974d1354eb5d0433bd0e.pdf} } @article { author = {Fathi, Leila and Faezipoor, Mohammad mehdi and Bahmani, Mohsen}, title = {Effect of UF and MUF resins on the practical properties of particleboard produced from rice straw and aspen particles}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {25}, number = {2}, pages = {321-331}, year = {2010}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2010.117318}, abstract = {In this investigation the effect of using of UF and MUF Resins on Physical and mechanical Properties of Particleboards Produced  from Rice Straw and Aspen Particles has been studied. The aim of this study was to determine of physical and mechanical properties of rice straw– particleboard. Single-layer particleboard was produced. That was produced with 11% MUF and 11% UF. For using of UF and MUF 2% hardener was added to adhesives. The Press condition for MUF was: 1750C for 4 minutes and also for UF application was 1750C for 6 minutes. Another variable factor was the rice straw content in three levels (15%, 30% and 45%). Other factors such as board density (0/7gr/cm3), mat moisture (12%) were constant factors. The results indicate that increasing rice straw to wood particles cause some reduction in modulus of rupture , and internal bonding , and some increase in thickness swelling , and water absorption of manufactured boards. But comparing and grouping means by Duncan test showed that in the most case these effects were insignificant when rice straw add to wood particle up to 30%. Particleboard bonded with 11% MUF had the highest bending strength. Particleboards bonded with MUF had better bending strength, shear strength, thickness swelling and water absorption after 2, 24 hours immersion. Grouping the experimental data while using Duncan method was indicated of the fact that an optimum condition for manufacturing particleboard while using a mixture of rice straw and wood particles is to add 30% rice straw to the mixture , use 11% melamine urea formaldehyde resin and employ a pressing time of 4 minutes.                                                                                              }, keywords = {Particleboard,UF,MUF,Rice straw,MECHANICAL PROPERTIES}, title_fa = {بررسی اثر دو نوع چسب MUF و UFبر روی خواص کاربردی تخته خرده چوب ساخته شده از مخلوط کلش برنج و خرده چوب صنوبر}, abstract_fa = {در این بررسی، تاثیر استفاده از دو نوع چسب ملامین اوره فرمالدئید ( MUF) و اوره فرمالدئید(UF) بر روی خواص فیزیکی و مکانیکی تخته خرده چوبهای ساخته شده از مخلوط کلش برنج و خرده چوب صنوبر مورد مطالعه قرار گرفت. نوع چسب ، اوره‌فرمالدئید و ملامین اوره‌فرمالدئید و نسبت کلش برنج و خرده چوب صنوبر در چهار سطح (100:0، 85:15 ، 70:30 و 55:45) به عنوان عوامل متغیر در نظر گرفته شد. دمای پرس (175درجه سانتی گراد)، زمان پرس(4دقیقه برای ملامین اوره‌فرمالدئید و 6 دقیقه برای اوره‌فرمالدئید)، رطوبت کیک (12درصد)، دانسیته تخته‌ها (75/0گرم برسانتیمتر مکعب) عوامل ثابت این تحقیق بودند. جهت ارزیابی خواص کیفی نمونه‌ها میزان جذب آب و واکشیدگی ضخامت پس از 2 و 24 ساعت غوطه وری در آب، مقاومت خمشی( مدول گسیختگی ) و چسبندگی داخلی آنها بر اساس استانداردهای 16983 ISO  و 68763 DIN اندازه‌گیری شد.  نتایج این بررسی نشان می‌‌دهند که افزایش کلش برنج به خرده‌چوبهای صنوبر باعث افزایش جذب آب و واکشیدگی ضخامتی، کاهش مقاومت خمشی و چسبندگی داخلی تخته‌های ساخته شده می‌‌گردد. اما تجزیه و تحلیل آماری و گروه‌بندی می‌انگین ها بر اساس آزمون دانکن نشان داد که در اغلب موارد افزایش کلش برنج تا میزان 30درصد اثرات منفی قابل اغماض برجای می‌گذارد. نمونه‌های ساخته شده با چسب ملامین اوره‌فرمالدئید خواص مکانیکی (مقاومت خمشی و چسبندگی‌داخلی)، واکشیدگی ضخامت و جذب‌آب مطلوب‌تری از تخته‌های ساخته شده با چسب اوره‌فرمالدئید داشتند. براساس نتایج این تحقیق با افزودن 30 درصد کلش برنج به خرده چوب صنوبر و مصرف 11درصد رزین ملامین اوره‌فرمالدئید و زمان پرس 4 دقیقه با فشار پرس  kg/cm235 و حرارت پرس 175درجه سانتی‌گراد می‌توان تخته‌هایی تولید کرد که از نظر مقاومت خمشی، مدول الاستیسیته، چسبندگی داخلی، جذب آب و واکشیدگی ضخامتی مطلوب باشند.}, keywords_fa = {تخته خرده چوب,اوره‌فرمالدئید,ملامین اوره‌فرمالدئید,کلش‌برنج,خواص مکانیکی}, url = {https://ijwpr.areeo.ac.ir/article_117318.html}, eprint = {https://ijwpr.areeo.ac.ir/article_117318_1afd4bc3ec995379b2f82f82fce61384.pdf} }