@article { author = {Hosseinzadeh, Abdolrahman and Fakhryan roghani, Abbas and Nourbakhsh, Amir and Golbabaei, Fardad}, title = {Comparative study on Pulping characteristics of Carpinus betulus and Parotia oersica woods}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {9}, number = {9- شماره 225}, pages = {1-33}, year = {2000}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2000.117492}, abstract = {In this investigation some anatomical, chemical and pulping suitability of two Iranian hardwood species which predominate in the Caspian forests were examined. The species are carpinus betulus (Hornbeam) and parotia persica (Ironwood).The results of this study revealed that:The average fiber length of carpinus betulus is 1.4 mm., fiber diameter 18 mm, and cell wall thickness 3.37 mm, while inparotia persica, fiber length, cell diameter and cell wall thickness are 1.34 mm, 17.3 mm and 3.48 mm respectively.The overall average of cellulose content: of carpinus betulus and Parotia persica were measured at 48.5, and 46.1 percent, and the lignin content at 17.5 and 21.5 percent respectively.The wood of each of the above species was cooked by means of a kraft process without difficulty but, there was a slight decrease in yield and kappa number with increase active alkali.The pulping yield with active alkali of14% was about 49.6 and with 20% was 43.44 percent, while the pulping yield of parotia persica in active alkali of 14% was 43.04 and in 20% about 37.79 percent. Thus, it may be concluded that for production of wrapping paper from carpinus betulus and parotia percica, using active alkali of 14% might give better quality paper and for production of printing paper from these two species active alkali of 20 percent might be desirable.}, keywords = {Carpinus betulus,Parotia oersica,anatomical,chemical and pulping suitability}, title_fa = {بررسی مقایسه ای ویژگیهای کاغذدهی چوب گونه های ممرز و انجیلی}, abstract_fa = {در این تحقیق ویژگی های آناتومیکی، شیمیایی و خمیر کاغذ چوب در دو گونه ممرز و انجیلی مورد مطالعه قرار گرفته است. میانگین طول الیاف چوب گونه ممرز 1.4 میلیمتر و میانگین قطر حفره سلولی و ضخامت دیواره الیاف آن به ترتیب 18 میکرون و 3.37 میکرون اندازه گیری شده است. میانگین طول الیاف، قطر حفره سلولی و ضخامت دیواره الیاف چوب گونه انجیلی به ترتیب 1.35 میلیمتر، 17.3 و 3.48 میکرون بدست آمده است. میزان سلولز چوب گونه ممرز به طور متوسط 48.5 درصد و لیگنین آن 17.5 درصد و میانگین سلولز و لیگنین چوب انجیلی به ترتیب 46.1 درصد و 21.5 درصد اندازه گیری شده است.نتایج این تحقیق نشان می دهد که در اثر افزایش قلیاییت فعال بازده خمیر کاغذ و عدد کاپا نیز کاهش می یابد. بازده خمیر کاغذ ممرز در قلیاییت فعال 14 درصد 49.6 و در 20 درصد 43.94 درصد و بازده خمیر کاغذ چوب انجیلی در قلیاییت فعال 14 درصد 43.04 درصد و در 20 درصد 37.79 درصد شده است.}, keywords_fa = {ممرز,انجیلی,ترکیب شیمیایی,ابعاد الیاف,خمیر کاغذ,فرایند کرافت,بازده,عدد کاپا}, url = {https://ijwpr.areeo.ac.ir/article_117492.html}, eprint = {} } @article { author = {Hajihassani, Reza and Hosseinzadeh, Abdolrahman and Nourbakhsh, Amir and Kargarfard, Abolfazl and Golbabaei, Fardad}, title = {INVESTIGATION ON THE POTENTIAL OF EUCALYPTUS CAMALDULENSIS WOOD IN PARTICLEBOARD INDUSTRY}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {9}, number = {9- شماره 225}, pages = {35-109}, year = {2000}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2000.117493}, abstract = {In this investigation Eucalyptus camaldulensis wood for particle -board production and determinating physical and mechanical properties of boards have been studied. Variable factors such as resin content in three levels (9, 10 and 11 percent) and press time in three levels (5, 6 and 7 minutes) were investigated.Other factors such as resin type, hardner type, closing press time, mat moisture, board density and etc. were assumed constant. Three boards were produced for each combination of variables. Based on the DIN-68763 standard physical and mechanical properties including Modulus of Rupture (MGR), Modulus of Elastisity (MOE), Internal Bonding (IB) and thickness swelling (TS2 and TS24) after 2 and 24 hours immersion in water were tested.Based on the factorial experimental design at completely random block test data was analysis. The rcsuHs showed that polymerization of resin could be better at the amount of 11 percent resin content and 7 minutes of press time for partideboard production from Eucalyptus camaldulensis wood.}, keywords = {}, title_fa = {امکان بالقوه استفاده از چوب اکالیپتوس کاملدولنسیس در صنایع تخته خرده چوب}, abstract_fa = {همگام با توسعه صنعت تخته خرده چوب لازم است که اقداماتی در جهت افزایش کیفیت محصول تولید شده (هم از لحاظ کیفی و هم از لحاظ کمی) و نیز کاهش هزینه های تولید صورت گیرد. دستیابی به چنین اهدافی تنها با تحقیقات گسترده و کاربردی در این صنعت میسر می باشد.در این بررسی از گونه چوبی اکالیپتوس کاملدولنسیس، تخته های آزمایشگاهی ساخته شده است. همچنین از سه میزان چسب 9، 10 و 11 درصد (بر اساس وزن خشک چسب) و سه زمان پرس 5 و 6 و 7 دقیقه به عنوان کامل متغیر استفاده گردیده و سپس اثر مستقل و متقابل این عوامل بر خواص فیزیکی و مکانیکی تخته های ساخته شده مورد ارزیابی قرار گرفته اند. نتایج حاصل از این بررسی ها به شرح زیر ارایه می شود: نتایج حاصل از اندازه گیری مقاومت خمشی تخته خرده چوب های ساخته شده از گونه اکالیپتوس نشان می دهد که تخته های تهیه شده در شرایط 11 درصد چسب و زمان پرس 7 دقیقه دارای بیشترین مقاومت خمشی و تخته هایی که در شرایط 9 درصد چسب و زمان پرس 5 دقیقه تهیه شده اند پایین ترین مقاومت خمشی را داشته اند.همچنین نتایج حاصل از اندازه گیری مدول الاستیسیته (MOE) تخته خرده چوب های ساخته شده نشان می دهند که تاثیر میزان چسب مصرفی و زمان پرس بر MOE تخته خرده چوب اثر معنی داری داشته، به طوری که میانگین MOE تخته خرده چوب های تهیه شده در شرایط 11 درصد چسب و زمان پرس 7 دقیقه در مقدار حداکثر بوده و در میزان چسب 9 درصد و زمان پرس 5 دقیقه به پایین ترین حد خود رسیده است.آزمایش های تعیین مقاومت چسبندگی داخلی (IB) تخته های تهیه شده نشان داده است که میزان چسب و زمان پرس تاثیر مستقل معنی داری بر IB داشته ولی دارای اثر متقابل معنی داری نمی باشند، به طوری که مقدار IB با افزایش میزان چسب افزایش یافته ولی با افزایش زمان پرس از 6 به 7 دقیقه مقاومت چسبندگی داخلی کاهش یافته است، به طوری که آرمانی ترین شرایط برای ساخت تخته هایی با مقاومت چسبندگی داخلی زیاد شرایط ساخت، 11 درصد چسب و زمان پرس 6 دقیقه به دست آمده است.نتایج آزمایش های واکشیدگی ضخامت بعد از 2 و 24 ساعت نشان داده است که افزایش میزان چسب و زمان پرس باعث کاهش واکشیدگی ضخامتی تخته های تهیه شده گردیده است به طوری که در شرایط ساخت 9 درصد چسب و زمان پرس 5 دقیقه بیشترین واکشیدگی ضخامتی و در شرایط 11 درصد چسب و زمان پرس 7 دقیقه کمترین واکشیدگی ضخامتی بدست آمده است.}, keywords_fa = {}, url = {https://ijwpr.areeo.ac.ir/article_117493.html}, eprint = {} } @article { author = {Hosseinzadeh, Abdolrahman and Toghraie, Nooshin and Golbabaei, Fardad}, title = {Engineering properties of Hornbeam wood in Veisar region}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {9}, number = {9- شماره 225}, pages = {109-149}, year = {2000}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2000.117494}, abstract = {To determine major engineering properties of Hornbeam wood (Carpinus betulus L.) in Vaisar region of Caspian Forests (North of Iran), adopting ASTM (D-143) Standard specifications, the matched small clear specimens were prepared. The test materials were derived from three randomly chosen trees. Mechanical and physical properties were measured on two moisture states: green and air - dried (at 12% moisture content).The influence of locations of specimens in the height of tree trunks and geographical directions were tested on target properties. From the results of this study it could be concluded that, there were no significant differences between the various heights and geographical directions from the pith for most of the properties investigated.Toughness was not influenced by moisture content. The average value of hardness of Hornbeam wood in transverse sections were the same as side_grain sections in green condition, but air-drying caused increasing the value of cross - sections about 30% The compression strength perpendicular r to the grain showed differences in wet and dry conditions.}, keywords = {HORNBEAM WOOD,Carpinus betulus L,Vaisar region,Mechanical and physical properties}, title_fa = {بررسی ویژگیهای فیزیکی و مکانیکی گونه ممرز از رویشگاه ویسر مازندران}, abstract_fa = {به منظور اندازه گیری خواص مهم مکانیکی چوب گونه ممرز Carpinus betulus L. در ناحیه ویسر، با رعایت اصول آیین نامه D-143 استاندارد ASTM برای آزمایش نمونه های کوچک و سالم جور از این گونه در منطقه ویسر از سه درخت نمونه به طور تصادفی، نمونه برداری و خواص مکانیکی آن در دو حالت سبز و خشک اندازه گیری گردید. اثر ارتفاع، جهات جغرافیایی و میزان رطوبت چوب، در نمونه های آزمایشی بوسیله تجزیه واریانس و آزمون F معین و جهت تعیین بهترین نمونه ها، گروه بندی دانکن در دو سطح 5% و 1% انجام گرفت. نتایج این بررسی نشان دهنده آن است که در این رویشگاه از نظر خواص مکانیکی، در جهات مختلف جغرافیایی و نیز ارتفاعات مختلف تنه از سطح زمین می توان از تفاوت های موجود چشم پوشی نمود. بررسی میانگین های بدست آمده نشان می دهد که اثر رطوبت به رغم اکثر موارد، در مورد مقاومت در برابر ضربه چوب بسیار ناچیز و در حد صفر است. همچنین سختی چوب در جهات جانبی و انتهایی در حالت سبز تفاوت چندانی ندارند در حالیکه بعد از خشک شدن سبب برتری سختی سطح عرضی به میزان 30% می گردد. اثر رطوبت در مقاومت به کشش عمود بر الیاف نیز در حد بسیار ناچیزی قرار دارد. تغییرات خواص مورد بررسی در طول تنه درخت و در دو حالت سبز و خشک در جدول ها و نمودارهای شماره 15-1 نشان داده شده است.}, keywords_fa = {ممرز,خواص مهندسی,مدول الاستیسیته,جرم ویژه نسبی}, url = {https://ijwpr.areeo.ac.ir/article_117494.html}, eprint = {} }