@article { author = {Podinehpoor, Mohammad ali and Ebrahimi, Ghanbar and Tajvidi, Mehdi and Chahar mahali, Majid and Ramtin, Ali akbar}, title = {THE EFFECTS OF TWO KINDS OF AGRICULTURAL WASTES (WHEAT AND BARELY STRAWS) ON NRC% OF ASPEN PARTICLEBOARDS}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {21}, number = {شماره 2}, pages = {61-69}, year = {2006}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2006.117594}, abstract = {In this investigation, the influences of two kinds of agricultural wastes (wheat and barely straws) mixed with Aspen particles were studied for use as insulation boards. Barely and wheat straws were chosen because of their availability. The manufacturing parameters were: a specific gravity of 0.2, 0.4 and 0.6 gr/cm3, and residual agriculture contents (0/1 00, 10/90, 20/80 and 30/70 weight of residual agriculture/ wood particle) of 0, 10, 20 and 30wt%. A commercial urea-fonnaldehyde adhesive was used as composite binder. Sound absorption coefficients were measured at five frequencies (250, 500, 1000, 2000, and 4000 hertz).The results showed when frequencies increased, sound absorption increased until it reaches to 2000 hertz but in 4000 hertz, sound absorption decreased. Between manufacturing parameters, kind of straws didn't have significant influence on noise reduction coefficient. The best density for absorb waves under 1000 in hertz was 0.4 gr/cm3 with 30% of straws but for waves with frequency higher than 1000 in hertz the best density was 0.2 gr/cm3 with 30% of straws.}, keywords = {AGRICULTURAL WASTES,ASPEN,WHEAT AND BARELY STRAWS,SOUND ABSORPTION COEFFICIENT}, title_fa = {اثر ترکیب ضایعات کشاورزی (ساقه گندم و جو) و چوب صنوبر بر خواص صوتی تخته خرده چوب عایق}, abstract_fa = {در این بررسی تاثیر استفاده از ضایعات کشاورزی (ساقه گندم و جو) بر روی خاصیت جذب صوت تخته های ساخته شده توام با خرده های چوب صنوبر مورد مطالعه قرار گرفت. نوع ضایعات (ساقه گندم و ساقه جو)، با درصد اختلاط (0، 10، 20 و 30 درصد) و دانسیته (0.4, 0.2 و (gr/cm3 0.6 از عوامل متغیر در این تحقیق بودند. تخته ها همسان و با شرایط یکسان ساخته شده بودند. ضریب جذب صوت تخته ها در پنج فرکانس 250، 500، 1000، 2000 و 4000 هرتز اندازه گیری گردید. نتایج نشان دادند که با افزایش فرکانس، ضریب جذب صوت تخته ها تا سطح فرکانس 2000 هرتز افزایش می یابد ولی در فرکانس 4000 هرتز دچار افت می شود. در بین عوامل متغیر، اثر مشهود نوع ضایعات بر روی میزان جذب صوت تخته های آزمونی مشاهده نشده ولی درصد ضایعات و دانسیته نمونه ها بر میزان جذب صوت اثر مشهود داشت. در فرکانس های زیر 1000 هرتز درصد ضایعات و دانسیته اثر تشدید کننده مشهودی داشتند و به طور میانگین میزان جذب صوت را 23 درصد افزایش دادند اما در فرکانس های بیش از 1000 هرتز افزایش 30 درصدی ضایعات، میزان جذب را 25 درصد ارتقا داد.  }, keywords_fa = {ساقه گندم,ساقه جو,چوب صنوبر,ضریب جذب صوت}, url = {https://ijwpr.areeo.ac.ir/article_117594.html}, eprint = {https://ijwpr.areeo.ac.ir/article_117594_a70ae419870b1562ec914d348826525a.pdf} } @article { author = {Ramtin, Aliakbar and Doosthosseini, Kazem and Dadkhah tehrani, Behnaz and Podinehpoor, Mohammad ali and Chaharmahali, Majid}, title = {THE EFFECT OF RESIN AMOUNT AND ORIENTATION OF STRAND BOARD ON PHYSICAL AND MECHANICAL PROPERTIES}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {21}, number = {شماره 2}, pages = {70-77}, year = {2006}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2006.117595}, abstract = {The objective of this research was to characterize the physical and mechanical properties of Aspen OSB made with different percentage of resin as well as in different orientation of strand. Mechanical and physical properties such as bending strength. interlaminated shear strength, water absorption and thickness swell were measured on the resulting orientation strand board. Among sample boards with high percentage of resin amount showed superior mechanical and physical performance. Results also showed, when strand were oriented in boards) physical and mechanical properties were improved.}, keywords = {ORIENTED STRAND BOARD,ASPEN,RESIN (U.F.),PHYSICAL AND MECHANICAL PROPERTIES}, title_fa = {بررسی اثر جهت دهی و مقدار رزین (اوره فرمالدهید) بر خواص فیزیکی و مکانیکی تخته تراشه ساخته شده از صنوبر}, abstract_fa = {در این پروژه اثر جهت دهی تراشه ها و مقدار رزین بر برخی خواص فیزیکی و مکانیکی تخته تراشه های ساخته شده از چوب صنوبر مورد بررسی قرار گرفت. تخته ها از نظر جهت دهی به دو صورت تصادفی (بدون جهت) و جهت دار (لایه های سطحی و لایه مغزی عمود بر هم) و با مقدار رزین اوره فرم آلدهید در دو سطح 8 و 10 درصد ساخته شدند. شرایط ساخت برای همه تخته ها ثابت در نظر گرفته شد. خواص مکانیکی شامل مدول گسیختگی (MOR)، مقاومت برشی موازی با سطح و خواص فیزیکی شامل درصد جذب آب و واکشیدگی ضخامت بعد از 24 ساعت اندازه گیری شدند. نتایج به دست آمده نشان داد که جهت دار کردن تراشه ها باعث افزایش مدول گسیختگی و کاهش مقاومت برشی موازی با سطح تخته ها شده است. همچنین افزایش مقدار رزین اثر معنی داری بر کلیه خواص فیزیکی و مکانیکی نشان داد.  }, keywords_fa = {تراشه,صنوبر,اوره فرمالدهید,تخته جهت دار,تخته تصادفی,مقاومت برشی موازی سطح,مقاومت خمشی,جذب آب,واکشیدگی ضخامت}, url = {https://ijwpr.areeo.ac.ir/article_117595.html}, eprint = {https://ijwpr.areeo.ac.ir/article_117595_497fd5ae322b5df5c13cdfd2c4115097.pdf} } @article { author = {Amiri, Shamohammad and Jahan latibari, Ahmad}, title = {THE INVESTIGATION ON ANATOMICAL, CHEMICAL AND PHYSICAL CHARACTERISTICS OF SAXAUL WOOD (HALOXYLON PERSICUM) FROM HARESABAD-E-SABZEVAR}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {21}, number = {شماره 2}, pages = {78-94}, year = {2006}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2006.117596}, abstract = {For the determined of Anatomical, Chemical and Physical characteristics of SAXAUL wood (Haloxylon persicum) from Haresabad-e-Sabzevar research station located in Khorasan-e- Razavi province 4 trees from this specie were selected and cut. Samples transferred to the Chemical laboratory in Alborz-e-Karaj research center for studies. Anova-1 in mstat-c statistical software was used for statistical analysis. Anatomical characteristics measured Fiber length, Fiber diameter, lemun and cell wall thickness 336.22, 13.61, 3.68 and 4.99 micron, respectively. Paper making coefficients were also measured. Mix up coefficient; Flexibility coefficient and Rankle coefficient were 24.72, %27.05 and %2.71, respectively. Chemical characteristics measured cellulose, lignin, alcol-acetone soluble extractives, NaoH 1% soluble extractives, hot water soluble extractives and ash 46.50%, 29.54%, 7.37%, 16.25%, 6.92% and 1.27%, respectively. Physical characteristics measured of density, dry density and critical density 1024.25, 1003.83 and 913 gr. per cubic centimeter.  }, keywords = {SAXSUL,ANATOMICAL CHARACTERISTICS,CHEMICAL CHARACTERISTICS,PHYSICAL CHARACTERISTICS,Density}, title_fa = {بررسی خصوصیات آناتومیکی، شیمیایی و فیزیکی چوب زرد تاغ (Haloxylon persicum) منطقه حارث آباد سبزوار}, abstract_fa = {به منظور تعیین خصوصیات آناتومی، شیمیایی و فیزیکی چوب زرد تاغ Haloxylon persicum منطقه حارث آباد سبزوار تعداد 4 اصله از آن درختچه به طور تصادفی انتخاب و قطع گردید. نمونه ها جهت انجام مطالعات به آزمایشگاه شیمی بخش تحقیقات علوم چوب و کاغذ البرز کرج انتقال داده شد.در بررسی خصوصیات آناتومی طول الیاف چوب تاغ 336.2 میکرون، قطر کلی الیاف 13.61 میکرون، قطر حفره سلولی3.68 میکرون و ضخامت دیواره الیاف 4.99 میکرون اندازه گیری شد. بر اساس اندازه گیری های انجام گرفته ضریب در هم رفتگی (لاغری)، ضریب انعطاف پذیری (نرمش) و ضریب مقاومت در برابر پاره شدن (رانکل) به ترتیب برابر با 24.72 واحد،27.05 درصد و 2.71 درصد محاسبه شد.در بررسی خصوصیات شیمیایی چوب تاغ دارای میانگین سلولز %46.5، لیگنین %29.54، مواد استخراجی محلول در الکل- استن %7.37، مواد استخراجی محلول در سود سوزآور %16.25 (%1)، مواد استخراجی محلول در آب داغ %6.92و نیز خاکستر %1.27 می باشد.در بررسی خصوصیات فیزیکی چوب تاغ، جرم مخصوص ظاهری آن 1.02 گرم بر سانتیمتر مکعب، جرم مخصوص خشک آن1.004 گرم بر سانتیمترمکعب و جرم مخصوص بحرانی آن 0.913 گرم بر سانتیمتر مکعب تعیین گردید. با استفاده از طرح کامل تصادفی توسط نرم افزار آماری MSTAT-C میانگین اندازه گیری ها میان درختان محاسبه گردید. جهت تجزیه و تحلیل نهایی از آزمون دانکن در سطح اعتماد 5% استفاده شد.}, keywords_fa = {زرد تاغ,خصوصیات آناتومیکی,خصوصیات شیمیایی,خصوصیات فیزیکی,وزن مخصوص}, url = {https://ijwpr.areeo.ac.ir/article_117596.html}, eprint = {https://ijwpr.areeo.ac.ir/article_117596_f11a5de65a4cbcd351f3be183bb5101d.pdf} } @article { author = {Kargarfard, Abolfazl and Nourbakhsh, Amir and Golbabaei, Fardad}, title = {INVESTIGATION ON UTILIZATION OF COTTON STALK IN PARTICLEBOARD PRODUCTION}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {21}, number = {شماره 2}, pages = {95-104}, year = {2006}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2006.117597}, abstract = {The purpose of this study was to investigation the utilization of cotton stalk and Eucalyptus wood (E. Camaldulensis) in particleboard production. Experimental boards were produced with using of 0, 25, 50 and 75% cotton stalk particles with Eucalyptus wood particles, press time at 3, 4 and 5 minutes. 36 boards were produced and physical & mechanical properties of their tested and analyzed. The results indicated that the modulus of rupture (MOR) and modulus of elasticity (MOE) of boards with increasing of cotton stalk particles were modified significantly, and MOR and MOE of boards produced with 75% cotton stalk and 25% of Eucalyptus wood particles were maximum. The results indicated that the internal bonds (IB) of boards with increasing press time were improved and the IB of boards produced at 5 minutes of press time was maximum, in order to the lowest of thickness swelling (T.S) of boards observed in same conditions. However thickness swelling of boards produced with 50 and 75% cotton stalk were higher than other treatments, significantly. The results of this study showed that in conditions that apply of species with high density such as Eucalyptus is unavoidable in particleboard production. Between 50 to 75 percent of wood materials that utilized in particleboard production, can be obtained from cotton stalk and with apply of their in particleboards can be produced particleboards in standard levels.}, keywords = {}, title_fa = {بررسی امکان کاربرد ساقه پنبه در ساخت تخته خرده چوب}, abstract_fa = {هدف از این تحقیق، بررسی امکان استفاده از ساقه پنبه و چوب اکالیپتوس (E. Camaldulensis) در تولید تخته خرده چوب بوده است. بنابراین با اضافه کردن صفر، 25، 50 و 75 درصد ذرات ساقه پنبه به خرده چوب تهیه شده از اکالیپتوس کاملدولنسیس و استفاده از 3 زمان پرس 3، 4 و 5 دقیقه اقدام به ساخت تخته های آزمایشگاهی گردید و خواص فیزیکی و مکانیکی آنها اندازه گیری شد.نتایج حاصل از اندازه گیری مقاومت خمشی (MOR) و مدول الاستیسیته (MOE) تخته ها نشان داد که با افزایش مقدار ساقه پنبه به ترکیب چوبی در سطح معنی داری این ویژگی ها بهبود یافته است. به طوری که این دو ویژگی برای تخته های ساخته شده در شرایط استفاده از 75 درصد ساقه پنبه و 25 درصد چوب اکالیپتوس حداکثر بوده است. همچنین با افزایش زمان پرس، مقاومت خمشی تخته ها بهبود یافته است. نتایج حاصل از اندازه گیری چسبندگی داخلی (IB) تخته ها نشان داد که افزایش زمان پرس باعث بهبود چسبندگی داخلی گردیده است و تخته های ساخته شده با استفاده از زمان پرس 5 دقیقه دارای بالاترین چسبندگی داخلی بوده اند. به همین دلیل در این شرایط، حداقل واکشیدگی ضخامت در تخته ها مشاهده گردید، هر چند مقدار واکشیدگی ضخامتی تخته های ساخته شده از ترکیب چوبی دارای 50 و 75 درصد ساقه پنبه به طور معنی داری بالاتر از بقیه تیمارها بوده است.نتایج این بررسی نشان می دهد که در شرایطی که استفاده از گونه هایی مانند اکالیپتوس با جرم مخصوص بالا در ساخت تخته خرده چوب اجتناب ناپذیر می باشد کاربرد ساقه پنبه به عنوان یک مکمل بهبود دهنده خواص مکانیکی توصیه می گردد.}, keywords_fa = {تخته خرده چوب,ساقه پنبه,اکالیپتوس کاملدولنسیس,ویژگیهای فیزیکی و مکانیکی}, url = {https://ijwpr.areeo.ac.ir/article_117597.html}, eprint = {https://ijwpr.areeo.ac.ir/article_117597_dc5c490489ae84ab0c2fba54b577a295.pdf} } @article { author = {Mahdavi, Saeed and habibi, masoudreza and hossein, kermanian}, title = {INVESTIGATION OF PROPERTIES OF ETHANOL-ALKALI, KRAFT AND SODA PULPS PREPARED FROM WHEAT STRAW}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {21}, number = {شماره 2}, pages = {105-114}, year = {2006}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2006.117598}, abstract = {Global concerns for preservation of forests and elimination of pollution from pulping and papermaking processes has led us to explore alternate fibrous resources other than wood and new environmentally begin pulping and bleaching processes for papermaking without sacrificing quality. Various alternate fibrous resources such as agricultural residues are already in use in many countries and considerable research have been undertaken to produce pulps by conventional and non-conventional processes. Wheat straw has high quantity among agricultural residues in Iran. Kraft, Soda and Ethanol-alkali pulping were carried out after sampling and preparing of wheat straw. Retention of carbohydrates is improved compared to the alkaline pulping processes, resulting in about 8 to 15 % higher yield at the same level of residual lignin. There was lower energy consumption for refining Ethanol-alkali pulps. There were no statistical differences among the physical properties. The strengths of Ethanol-alkali pulps consist of tear index, burst index and breaking length were lower than alkaline pulps, but all of the strength properties were higher than kraft and liner paper except tear index that addition of some long fiber can solve the problem.}, keywords = {WHEAT STRAW,ETHANOL PULP,KRAFT,SODA,TEAR,BURST,BREAKING LENGTH}, title_fa = {بررسی ویژگیهای خمیر کاغذ اتانل- قلیا و با خمیر کاغذ کرافت و سودای تهیه شده از کاه گندم}, abstract_fa = {لزوم حفاظت از جنگل ها و رفع آلودگی های ناشی از بکارگیری فرآیندهای متداول تولید خمیر و کاغذ، چاش جدی را به منظور کاهش استفاده از چوب و بکارگیری فرآیندهای زیست سازگار همراه با حفظ کیفیت محصول، طلب می کند. در بسیاری از کشورها، استفاده از منابع غیر چوبی مانند پسماند گیاهان زراعی از مدت ها قبل برای تولید خمیر کاغذ به روش های متداول و غیرمتداول مطرح بوده است. از لحاظ کمیت، کاه گندم بیشترین مقدار را در میان سایر پسماندهای زراعی در ایران و جهان داراست.کاه گندم پس از آماده سازی، با استفاده از سه فرآیند کرافت، سودا و اتانل- قلیا به خمیر کاغذ تبدیل شد. در عدد کاپای مشابه، خمیر کاغذ اتانل- قلیا نسبت به دو خمیر کاغذ کرافت و سودا دارای بازده بعد از الک بیشتری (8.3 تا 15.8 درصد) بود. مدت زمان نسبتا کمتر برای پالایش خمیر کاغذ اتانل- قلیا به عنوان یک مزیت مطرح است. ویژگی های فیزیکی سه نوع خمیر کاغذ تهیه شده از کاه گندم، تفاوت محسوسی با هم نداشتند در حالی که ویژگی های مقاومتی خمیر کاغذ اتانل- قلیا به نحو عمده نسبت به دو نوع دیگر خمیر کاغذ کمتر بودند. البته به این ویژگی ها به جز شاخص پارگی کاغذ اتانل- قلیا در مقایسه با ویژگی های کاغذ کرافت و لاینر بیشتر بوده که برای جبران این ضعف، می توان از اختلاط مقداری خمیر کاغذ الیاف بلند استفاده نمود.}, keywords_fa = {کاه گندم,خمیر کاغذ,اتانل- قلیا,کرافت,سودا,شاخص پارگی,شاخص ترکیدن,طول پاره شدن}, url = {https://ijwpr.areeo.ac.ir/article_117598.html}, eprint = {https://ijwpr.areeo.ac.ir/article_117598_570f54abe34aceda033f3a1e728f73d3.pdf} } @article { author = {Nourbakhsh, Amir and Kargarfard, Abolfazl}, title = {THE EFFECTS OF DENSITY AND PRESS TIME ON POPLAR INSULATION PARTICLEBOARD PROPERTIES}, journal = {Iranian Journal of Wood and Paper Science Research}, volume = {21}, number = {شماره 2}, pages = {115-122}, year = {2006}, publisher = {Research Institute of Forests and Rangelands}, issn = {1735-0913}, eissn = {2383-112X}, doi = {10.22092/ijwpr.2006.117599}, abstract = {In this research utilization of Poplar Insulation particleboard at two different level of density (0.35, 40, 45 and 50gr/cm3) and press time (2, 3 and 4 min) were considered. Based on the DIN standard physical and mechanical properties including MOR, MOE, IB and thickness swelling (after 2 and 24 immersion in water) were tested. Based on the factorial experimental design at completely random test was analysis. The effect of density from 0.35 to 0.50gr/cm3, MOR, MOE and IB were increased and thickness swelling after two and 24 hours immersion in water were decreased .Moreover the effect of Press time from 2 to 4 min. MOR and MOE increased and at 3 min. IB was increased.}, keywords = {POPLAR INSULATION PARTICLEBOARD,Density,V.F,press time}, title_fa = {اثر دانسیته و زمان پرس بر ویژگیهای تخته خرده چوب عایقی از گونه صنوبر}, abstract_fa = {در این بررسی شرایط ساخت تهیه خرده چوب عایقی از گونه صنوبر با هدف تعیین ویژگی های فیزیکی و مکانیکی تخته ها مورد مطالعه قرار گرفته است. دانسیته تخته خرده چوب عایقی در چهار سطح 0.45, 0.40, 0.35 و 0.50 گرم بر سانتیمتر مکعب و زمان پرس 2، 3 و 4 دقیقه به عنوان عوامل متغیر در نظر گرفته شدند.افزایش دانسیته از 0.35 تا 0.50 گرم بر سانتیمتر مکعب باعث افزایش مقاومت و مدول خمشی و چسبندگی داخلی شده است. همچنین افزایش زمان پرس از 2 به 4 دقیقه باعث افزایش مقاومت و مدول خمشی و زمان پرس 3 دقیقه باعث افزایش چسبندگی داخلی تخته خرده چوب گردیده است. با افزایش دانسیته تخته خرده چوب از 0.35 به 0.50 گرم بر سانتیمترمکعب کاهش میزان واکشیدگی ضخامت در تخته های ساخته شده ملاحظه می گردد. همچنین با افزایش زمان پرس از 2 به 3 دقیقه سبب کاهش میزان واکشیدگی ضخامت پس از 2 و 24 ساعت غوطه وری در آب می گردد.}, keywords_fa = {تخته خرده چوب عایقی,صنوبر,دانسیته,اوره- فرم آلدئید,و زمان پرس}, url = {https://ijwpr.areeo.ac.ir/article_117599.html}, eprint = {https://ijwpr.areeo.ac.ir/article_117599_79710908ad88dfab43c42ef52f912169.pdf} }