Document Type : Research Paper

Authors

Associate Prof., Wood and forest products division, Research Institute of Forests and Rangelands, Agricultural Research Education and Extension Organization (AREEO), Tehran, Iran,

Abstract

In this study, the effect of type II and III Portland cement and the use of undepithed and depithed sunflower stalks particles (Helianthus Annuus) with percentages of different mixing ratio of the poplar wood particles (Populous alba) with 100:0, 75:25, 50:50, 25:75 and 0:100 respectively in the manufacturing of wood-cement composites were studied. Physical and mechanical properties of boards were measured as the effect of lignocellulosic material (sunflower stalks andpoplar wood) and Portland cement type (II and III) on the cement setting time. The results of the study showed that the lignocellulosic material reduced the hydration reaction and increased cement setting time. In this regard, sunflower stalks particles in comparison with poplar wood particles increased cement setting time intensively. The boards made from type III Portland cement had better mechanical strength and physical properties (water absorption and thickness swelling reduced) than with type II Portland cement. In comparison with poplar wood particles usage, the use of sunflower stalks particles and more amount of it caused to mechanical properties decreases and increased the water absorption and thickness swelling after 2 and 24 h water immersion. Therefore the best characteristics were obtained in boards made from 100 percent poplar wood particles. In other hands, using depithed sunflower stalks particles caused to improved the physical and mechanical characteristics. In general, it can be concluded that 25 percent of depithed sunflower stalks particles relative to poplar wood particles (relative to mass lignocellulosic materials( with type III Portland cement in the manufactured wood-cement boards has suitable physical and mechanical properties for usage of these boards in interior building applications.

Keywords

Main Subjects

-AbdolaliSarbandi, M., Safdari, V., Sepidehdam, S.M.J. and Gangian, E., 2012. Effect of nano-silica and bagasee fibers on bending strength and physical properties of cement fiberboard. Iranian Journal of Wood and Paper Science Research, 27(1): 167-177.
-Aggarwal, L. K. and Singh, J. 1990. Effect of plant fibre extractives on properties of cement. Cement and Concrete Composites, 12(2): 103-108.
-Ashori, A., Tabarsa, T., Azizi, K. and Mirzabeygi, R., 2011. Wood–wool cement board using mixture of eucalypt and poplar. Industrial Crops and Products, 34(1): 1146-1149.
-ASTM C191-82., Standard Test Method for Time of Setting of Hydraulic Cement by Vicat Needle.  Annual Book of ASTM Standards (2004).
-EN 310, Wood-based panels - Determination of modulus of elasticity in bending and of bending strength. European committee for standardization (1993).
-EN 317, Particleboards and fiberboards - Determination of swelling in thickness after immersion in water. European committee for standardization (1993).
-EN 319, Particleboards and fiberboards - Determination of tensile strength perpendicular to the plane of the board. European committee for standardization (1993).
-Fernandez, E. C. and Taja-on, V.P., 2000. The use and processing of rice straw in the manufacture of cement-bonded fibreboard. Proceedings of a Workshop held in Canberra. Australia, 10 December: 49-54.
-Golbabaei, F., Hosseinkhani, H., Hajihassani, R. and Rashnv, A., 2013. Investigation on properties of wood-cement panels on agricultural residues. Iranian Journal of Wood and Paper Science Research, 28 (3): 583-596.
-Karade, S.R., 2010. Cement-bonded composites from lignocellulosic wastes. Construction and building materials, 24(8): 1323-1330.
-Khorami, M. and Sobhani, J., 2013. An experimental study on the flexural performance of agro-waste cement composite boards. International Journal of Civil Engineering, 11(4): 207-216.
-Nazerian, M. andSadeghiipanah, V., 2013. Cement-bonded particleboard with a mixture of wheat straw and poplar wood. Journal of Forestry Research, 24(2): 381-390.
-Pehanich, J.L., Blankenhorn, P.R., and Silsbee, M.R., 2004. Wood fiber surface treatment level effects on selected mechanical properties of wood fiber–cement composites. Cement and Concrete Research, 34(1): 59-65.
-Rahmanivasokalaei, y., Mobasser, H. R., GhanbariMaliDareh, A., Andarkhor, A. and Dastan, S., 2010. Determination of the best distance and plant density Lakomka sunflower varieties in Mazandaran. Iranian Journal of Research in Crop Science, 7 (2): 29-36.
-Rowell, P.M., Youngquist, J.A. and Mcnatt, D., 1991. Agricultural fibers in composition panels. In Proceedings of the 27th International Particleboard Composite Materials Symposium.USA, 9-11 April: 301-314.
-Sedan, D., Pagnoux, C., Smith, A. and Chotard, T., 2008. Mechanical properties of hemp fibre reinforced cement: Influence of the fibre/matrix interaction. Journal of the European Ceramic Society, 28(1): 183-192.
-Torkaman, J., Ashori, A. and Momtazi, A.S., 2014. Using wood fiber waste, rice husk ash, and limestone powder waste as cement replacement materials for lightweight concrete blocks. Construction and Building Materials, 50(1): 432-436.
-Vaickelionis, G. and Vaickelioniene, R., 2006. Cement hydration in the presence of wood extractives and pozzolan mineral additives. Ceramics Silikaty, 50(2): 115-122.
-Wolfe, R. W.and Gjinolli, A., 1999. Durability and strength of cement-bonded wood particle composites made from construction waste. Forest Products Journal, 49(2):  24-31.