Document Type : Research Paper

Authors

1 PhD, Wood and forest products division, Research Institute of Forests and Rangelands, Agricultural Research Education and Extension Organization (AREEO), Tehran, Iran

2 Wood Science & Forest Products Research Division Research Institute of Forests & Rangelands Tehran, Iran

3 Wood and Forest Products Science Research Division, Research Institute of Forests and Rangelands, Tehran, Iran,

4 Wood and Forest Products Science Research Division, Research Institute of Forests and Rangelands, Agricultural Research Education and Extension Organization (AREEO) P.O. Box 13185-116, Tehran, Iran

Abstract

The impact of reeds residue addition on physical and mechanical properties of particleboard made from pomegranate pruning was investigated. Laboratory particleboard  was made applying one of the three levels of   press time (3, 4 and 5 minutes) and  one of the four levels of reed and pomegranate pruning mixture (1-100% reeds; 2- 75% reeds + 25% pomegranate pruning; 3- 50% reeds + 50% pomegranate pruning and 4- 25% reeds + 75% pomegranate pruning). Boards were made in three replicate and 36 boards were made. Boards were tested using relevant EN standard and results were analyzed based on complete randomized design (CRD) under factorial experiment. Results revealed that increasing of pomegranate pruning in the wood mixture imposed positive effect on MOR, MOE, IB and thickness swelling of the particleboard. The relevant values of MOR, and MOE of the boards produced using 25% reeds + 75% pomegranate pruning  were determined as 16.20 MPa and 2533 MPa respectively. Also thickness swelling after for 2 and 24 hours soaking in water decreased from 17.51 and 33.21% to 9.33 and 16.84% respectively. Internal bond strength (IB) of boards made applying 3 minutes press time (0.17 MPa.) was higher than boards made pressed for either 4 or 5 minutes, which indicates that 3 minutes press time is the appropriate time to approach maximum MOR and minimum thickness swelling after 24 hours soaking in water.

Keywords

- امیری، سعید. بررسی اقتصادی نیزارهای هورالعظیم برای استفاده در صنایع لیگنوسلولزی، مجله منابع طبیعی ایران، شماره 46، سال 1372.
- پارساپژوه، داود. بررسی امکان استفاده از نیزار هورالعظیم، خلاصه نتایج طرح تحقیقاتی وزارت صنایع، 1386.
- حبیبی،م ر. 1384. نشریه تحقیقات علوم چوب و کاغذ ایران. مؤسسه تحقیقات جنگلها و مراتع کشور. جلد 20، شماره 1.
-  خادمی اسلام : 1370استفاده از سر شاخه درختان میوه در صنایع تخته‌خرده‌چوب مجله منابع طبیعی ایران شماره 40
- فامیلیان، ح. 1373. بررسی مقایسه ای خصوصیات بیولوژیکی، آناتومیکی، فیزیکی و شیمیایی نی در نیزارهای هورالعظیم وتالاب انزلی، پایان نامه کارشناسی ارشد، دانشکده منابع طبیعی دانشگاه تهران.
- نوربخش و همکاران (1380). بررسی امکان ساخت تخته‌خرده‌چوب از منابع لیگنوسلولزی جنوب ایران(امکان تولید تخته‌خرده‌چوب از ضایعات نخل و سرشاخه‌های چوب کهور پاکستانی). مؤسسه تحقیقات جنگلها و مراتع کشور، نشریه تحقیقات چوب و کاغذ شماره 15، شماره انتشار 278-1380 صفحه 61 تا 88..
- Board on Science Technology for International Development, USA Making aquatic Weeds Useful, NationalAcademy of Sciences, 1976.
- EN 310, 1996. Wood based panels, determination of modulus of elasticity in bending and bending strength. European Standardization Committee, Brussell.
- EN 317, 1996. Particleboards and fiberboards, determination of swelling in thickness after immersion. European Standardization Committee, Brussell.
- EN 319, 1996. Wood based panels, determination of tensile strength perpendicular to plane of the board. European Standardization Committee, Brussell.
- Ezzat, s. 1974. Leaves of date palm tree as a technical feasible source of raw material for paper production, cellulose chemistry, techn.8: 627-34.
- Hakkila, P. (1971) . Branches, stumps, and roots as future raw material sources. In forest Buiomass studies, ed H. young orono: univ of maine press.
 
- Huaykan Zhou,E.Ngguo,Xiaoning, 1996Najing Forestry University, 210037.D.R.china 20th      session of the international poplar commission Budapest 1-4,Oct.1996.proceeE.Ng Volume(1).
- Ryner A.A 1968. particleboards manufacture and application p. 11-25 IVY Hatch. Sevenoaks, Kent.
- Xiaobo, L. 2004. Physical, chemical and mechanical properties of Bambo and its utilization potential for fiberboard manufacturing. M. S. Thesis, Faculty of the LouisinaStateUniversity and Agriculture and MechanicalCollege.
- Yugi, Yu.,1983.  Non-Wood Plant Fiber Pulping, Ministry of Light Industry,