Research Paper
Composite wood products
Abdolrahman Hosseinzadeh; Amir Nourbakhsh; Abolfazl Kargarfard; Fardad Golbabaei; Morteza Nazeryan
Abstract
Decreasing availability of raw material for Iranian wood industries and the need to conserve our limited natural forests initiated research concerning the utilization of fast-growing species in particleboard production. The objective of this study was to investigate the possibility of particleboard production ...
Read More
Decreasing availability of raw material for Iranian wood industries and the need to conserve our limited natural forests initiated research concerning the utilization of fast-growing species in particleboard production. The objective of this study was to investigate the possibility of particleboard production from wood of two- year- old coppices of 17 experimental populus clones grown under intensive culture in the "Alborz Research Center" near Tehran. The furnish contained mixture of stem and branch wood with bark used to make 51 sample boards (3 board from each clone). Modulus of elasticity (MOE), modulus of rupture (MOR), internal bond strength (IB), thickness swelling and water absorption of the specimens were tested. The results indicate that sample boards made from Populus euramericana costanzo and populus euramericana 561.41 had significantly the highest MOR and MOE. But there was no significant differences in the internal bonding strength between different clones, while, those sample boards made from populus nigra betulifolia and Populus nigra nivea showed significantly the lowest percentages of thickness swelling. The average physical and mechanical properties of the particleboard samples produced from two- year- old coppices of poplar clones compared favourably to boards made from natural grown beech wood. Therefore, using UF resin, particleboard with acceptable quality particleboards can be produced from two- year- old poplar clones.
Research Paper
Physics and anatomy
Ahmad Jahan latibari; Fardad Golbabaei; Mohammad reza Amini
Abstract
Pinus teada, which was planted in Pelembera region, shows promising both in growth rate and adaptability. Even though the fiber geometry of P. teada wood in its native growth region is excellent, but for utilization of this wood in pulping, the knowledge of its technological characteristics especially ...
Read More
Pinus teada, which was planted in Pelembera region, shows promising both in growth rate and adaptability. Even though the fiber geometry of P. teada wood in its native growth region is excellent, but for utilization of this wood in pulping, the knowledge of its technological characteristics especially fiber geometry is required.Two trees of this species were randomly selected from Pelembera forests plantation in Gilan and after felling were cut in smaller bolts and transferred to wood &paper research laboratory, research institute of forests and rangelands. Five cross-sections with the thickness of 15 cm were cut from each tree and the cross-sections were used for selection of samples. Fiber geometry measurement samples were prepared from every five annual rings and from each sample, springwood (early wood) and summer wood (late wood) sample were cut separately. Preparations of fiber geometry samples were according to procedure developed by Franklin (1954) and from each sample the dimension of 30 complete and unbroken trachieds was measured.Trachied length, diameter, cell wall thickness and lumen diameter was measured for different elevation in tree and different growth rings in cross-section.Dimension of 3,00 trachieds were measured totally.Average trachied length, diameter, lumen diameter and cell wall thickness of early wood were measured at 3.65mm, 38.97 mm, 28.94 mm and 3.72 mm respectively. Related values for late wood is as follow: trachied length 3.84mm; diameter, 35.54 /lm; lumen diameter, 22.96 mm; and cell wall thickness, 6.29 mn. Average annual growths were measured at 5.66 mm and late wood percentage at 24.13. Felting, flexibility and runkel coefficients were calculated at 97.96, 73.48, and 26.74 respectively. The result of this study indicates that all measured properties increases with increasing the height of tree and from center (pith) toward outer regions (bark). However all the measured values decreased at highest as well as outer locations.Statistical analysis indicated that the difference in measured properties at different heights of trees from center to the bark is significantly different at 1% level.
Research Paper
Amir Nourbakhsh; Bohuslav V.Kokta; Abdolrahman Hosseinzadeh; Ahmad Jahan latibari; Abolfazl Kargarfard
Abstract
This study investigates the effect of maleic anhydride polypropylene (MAPP) addition as a coupling agent at four levels and also the type of cellulosic materials as a reinforcing component on processing and mechanical properties of modified Populus deltoides fiber and flour/ polypropylene composites.The ...
Read More
This study investigates the effect of maleic anhydride polypropylene (MAPP) addition as a coupling agent at four levels and also the type of cellulosic materials as a reinforcing component on processing and mechanical properties of modified Populus deltoides fiber and flour/ polypropylene composites.The results indicate that the interfacial bond between reinforcing-fiber/ flour and the matrix show great influence on the mechanical properties of composites. Furthermore it has been demonstrated that the addition of coupling agent during processing significantly improves the mechanical properties of fiber/ flour polypropylene composites. The results of this investigation indicates that the highest the mechanical properties of composites are as follow; The mechanical properties of the poplar fiber with 2% MAPP is higher than poplar flour without MAPP, which proves that the addition of functional group C=O acts as a good bonding agent. The notched Impact Izod strength value of poplar fiber with 2% MAPP is less than pure PP. But it is higher than other treatments. The results indicate that the interfacial bond between reinforcing fibers and flour with polymer matrix modified MAPP play a significant role in improving the measured mechanical properties of the composites.
Research Paper
Physics and anatomy
Saeed Mahdavi; Abdolrahman Hosseinzadeh; Hossein Familian; masoudreza habibi
Abstract
Cross sectional disks were cut at breast height from three 17-year-old trees of E.camaldulensis grown in Pasand research station in Mazandaran province. Ring width, wood density, and fiber dimension were measured for each two rings from pith to the bark. Overall average disks, fiber length, fiber width, ...
Read More
Cross sectional disks were cut at breast height from three 17-year-old trees of E.camaldulensis grown in Pasand research station in Mazandaran province. Ring width, wood density, and fiber dimension were measured for each two rings from pith to the bark. Overall average disks, fiber length, fiber width, lumen diameter, and cell wall thickness were measured at 758, 15.93, 8.63, and 3.65 micrometer respectively. Mean values for the oven dry and basic. Density was 0.708 g/cm3 and 0.552 g/cm3. Cross sectional \ growth rate and wood production for the trees were measured at 11.1 mm and 12.3 m3/ha./year respectively. Chemical compositions of the wood consist or cellulose, lignin, extractives (in acetone soluble) and ash were measured at 47.44%, 30.87%, 6.96%, and 0.27% respectively. The result showed that E.camaldulensis is classified as short fiber hardwood with low frequency. Fiber dimensions and density slightly increased from pith to the bark. There was high significant correlation between cell wall thickness and density, while; there was no significant correlation between ring width and the others. Among the properties studied, cell wall thickness and fiber length showed the most variations.
Research Paper
Management and Economics wood
Habib alah Arab tabar firoz jaei; Ali Reza nezhad; Abdolrahman Hosseinzadeh
Abstract
In this study, green round poles of Populus nigra L. var. italica were treated with Celcure by using Tire - Tube method. After felling and sizing trees, thick - end of poles (about 15 cm.) were debarked and a section of tire inner Tube was fastened around the debarked end of the fresh - cut poles and ...
Read More
In this study, green round poles of Populus nigra L. var. italica were treated with Celcure by using Tire - Tube method. After felling and sizing trees, thick - end of poles (about 15 cm.) were debarked and a section of tire inner Tube was fastened around the debarked end of the fresh - cut poles and bound tightly with rubber bands and the upper end of the tube was connected to the elevated solution container. Then the poles installed on slope and let them to absorb the solution. The results showed that sapwoods were completely penetrated but hartwood less after 8-24 hrs.
Research Paper
Management and Economics wood
Ali Reza nezhad; Habib alah Arab tabar firoz jaei; Abdolrahman Hosseinzadeh
Abstract
Four hardwood species including: Alder (Alnus subcordata), Oriental plane (Platanus orientalis), Eucalyptus camaldulensis and Babul (Acacia arabica) were treated with Creosote and Celcure. The dimension of samples was 20 x 7.5 x 2 cm. Both preservative treated and untreated samples were placed in seawater ...
Read More
Four hardwood species including: Alder (Alnus subcordata), Oriental plane (Platanus orientalis), Eucalyptus camaldulensis and Babul (Acacia arabica) were treated with Creosote and Celcure. The dimension of samples was 20 x 7.5 x 2 cm. Both preservative treated and untreated samples were placed in seawater (Boshehr in Persian Gulf) according to IRG/WP-4432 (1985). After 9, 15, 24, 29, 38, 47, 53, 58 and 64 months, the samples were inspected according with recommendation of IRG/WP-4432(1985) and ASTM D- 240. All the control samples (untreated wood) of Alder and Oriental plane over 9 months, Eucalyptus and Babul over 20 months, were seriously attacked. Treated samples with Celcure of Alder and Oriental plane after 38 months were completely damaged and Eucalyptus over 38 months were severely degraded. Creosote treated samples of Eucalyptus over 58 months and Babul over 38 months were seriously attacked. Creosote treated of Alder and Oriental plane samples after 64 months installation were sound. It can be concluded that treatment with Creosote using full cell process (Bethel) increased resistance of investigated wood species against marine borers.
