Volume 39 (2024-2025)
Volume 38 (2023-2024)
Volume 37 (2022-2023)
Volume 36 (2021-2022)
Volume 35 (2020-2021)
Volume 34 (2019-2020)
Volume 33 (2018-2019)
Volume 32 (2017-2018)
Volume 31 (2016-2017)
Volume 30 (2015-2016)
Volume 29 (2014-2015)
Volume 28 (2013-2014)
Volume 27 (2012-2013)
Volume 26 (2011-2012)
Volume 25 (2010-2011)
Volume 24 (2009-2010)
Volume 23 (2008-2009)
Volume 22 (2007-2008)
Volume 21 (2006-2007)
Volume 20 (2005-2006)
Volume 19 (2004-2005)
Volume 18 (2003-2004)
Volume 17 (2002-2003)
Volume 16 (2002-2003)
Volume 15 (2001-2002)
Volume 14 (2001-2002)
Volume 13 (2001)
Volume 12 (2000-2001)
Volume 11 (2000-2001)
Volume 10 (2000-2001)
Volume 9 (2000)
Volume 8 (1999)
Volume 7 (1999)
Volume 6 (1998)
Volume 5 (1998)
Volume 4 (1997)
Volume 3 (1997)
Volume 2 (1996)
Volume 1 (1995)
Number of Articles: 6
RELATIONSHIP BETWEEN MOISTURE CONTENT AND ULTRASONIC WAVE SPEED DURING KILN DRYING OF BASSWOOD LUMBER
Volume 21, No., 1 , May 2006, Pages 1-8
Abstract
Ultrasonic wave speed was measured in the longitudinal direction of Basswood on the top and bottom surfaces and center of lumbers during kiln drying in 3 Kiln load programs with final dry bulb of 80oC and different relative humidities. On the surfaces, wave speed decreased rapidly with MC declining from ... Read MoreTHE EFFECT OF SIT CONDITION ON SOME MECHANICAL PROPERTIES OF PICEA ABIES WOOD IN TWO REGIONS
Volume 21, No., 1 , May 2006, Pages 9-21
Abstract
In this study, in order to achieve sufficient accuracy both quality and quantity factors in two forestry plantanation of Picea abies using 100% statistics were used. In order to investigate wood quality, fiber length, density and mechanical properties, 4 thick cross section trees were selected and cut ... Read MoreINVESTIGATION ON THE PROPERTIES OF MEDIUM DENSITY FIBERBOARDS FROM MIXTURE OF SAXAUL AND HORNBEAM WOOD
Volume 21, No., 1 , May 2006, Pages 22-32
Abstract
The property of MDF obtained the mixture of Haloxylon persicum wood (Saxaul) with Carpinus betulus (Hornbeam) at 100:0, 75:25, 50:50, 0:100 ratios is investigated in this study. The results of this study showed that there is significant statistical differences (1%) among combinations of woods for MOR, ... Read MoreTHE EFFECT OF PRODUCING METHOD ON THE MECHANICAL PROPERTIES OF WOOD PLASTIC COMPOSITES MADE FROM PARTICLEBOARD WASTE
Volume 21, No., 1 , May 2006, Pages 33-42
Abstract
The possibility of producing wood-plastic panels using two methods including melt blend and dry blend was studied in this research. Methods were compared with each other in order to select the best. Wood-Plastic panels were made from high density polyethylene (as resin) and particle board waste (as natural ... Read MoreTHE COMPARISON ON PULPING OF P.AUSTRALIS
Volume 21, No., 1 , May 2006, Pages 43-51
Abstract
The common reed, P.australis, covers vast region in south of Iran. Specially, there is possibility of executing harvest in Hoor-Alazim canebrake as a reed natural provenance. It has good properties for papermaking in comparison of typical nonwood materials. Chips were pulped using typical kraft, soda ... Read MoreINVETIGATION ON DURABILITY OF EUCALYPTUS WOOD (E. INTERTEXTA R. T.BAKER) BY FIELD TEST STAKES
Volume 21, No., 1 , May 2006, Pages 52-60